Studies on dental high-speed cutting

Influence of oscillating and rotary cutting instruments with electric and turbine handpieces on tooth preparation surfaces

STATEMENT OF THE PROBLEM

Rotary and nonrotary cutting instruments are used to produce specific characteristics on the axial and marginal surfaces of teeth being prepared for fixed restorations. Oscillating instruments have been suggested for tooth preparation, but no comparative surface roughness data are available.

PURPOSE

To compare the surface roughness of simulated tooth preparations produced by oscillating instruments versus rotary cutting instruments with turbine and electric handpieces.

MATERIAL AND METHODS

Different grit rotary cutting instruments were used to prepare Macor specimens (n=36) with 2 handpieces. The surface roughness obtained with rotary cutting instruments was compared with that produced by oscillating cutting instruments. The instruments used were as follows: coarse, then fine-grit rotary cutting instruments with a turbine (group CFT) or an electric handpiece (group CFE); coarse, then medium-grit rotary cutting instruments with a turbine (group CMT) or an electric handpiece (group CME); coarse-grit rotary cutting instruments with a turbine handpiece and oscillating instruments at a low-power (group CSL) or high-power setting (group CSH). A custom testing apparatus was used to test all instruments. The average roughness was measured for each specimen with a 3-dimensional optical surface profiler and compared with 1-way ANOVA and the Tukey honestly significant difference post hoc test for multiple comparisons (α=.05).

RESULTS

Oscillating cutting instruments produced surface roughness values similar to those produced by similar grit rotary cutting instruments with a turbine handpiece. The electric handpiece produced smoother surfaces than the turbine regardless of rotary cutting instrument grit.

CONCLUSION

Rotary cutting instruments with electric handpieces produced the smoothest surface, whereas the same instruments used with a turbine and oscillating instruments achieved similar surface roughness.

The effect of cavity restoration variables on odontoblast cell numbers and dental repair

OBJECTIVES

Dentinal repair following cavity restoration is dependent on several parameters including the numbers of surviving odontoblasts. The purpose of this study was to examine the effects of cavity cutting and restoration treatments on post-operative odontoblast numbers.

METHODS

353 Standardised non-exposed rectangular Class V cavities, were cut into the buccal dentin of intact 1st or 2nd premolar teeth of 165 patients, aged between nine and 25 years of age. Composite cavity restorations with various etching treatments were compared with resin-modified glass ionomer cements, enamel bonding resins, as well as polycarboxylate, calcium hydroxide, and zinc oxide eugenol materials. Following tooth extraction (20-381 days) for orthodontic reasons, the area of the reactionary dentine and the area of the odontoblasts was measured histomorphometrically.

RESULTS

Odontoblast numbers and dentine repair activity were found to be influenced more by cavity restoration variables, than the choice of cavity filling materials or patient factors. The most important cavity preparation variable was the cavity remaining dentine thickness (RDT); below 0.25mm the numbers of odontoblasts decreased by 23%, and minimal reactionary dentine repair was observed.

CONCLUSIONS

Odontoblast injury increased as the cavity RDT decreased. In rank order of maintaining odontoblast numbers beneath restored cavities with a RDT below 0.5mm, and using calcium hydroxide for comparison; calcium hydroxide (100%), polycarboxylate (82.4%), zinc oxide eugenol (81.3%), composite (75.5%), enamel bonding resin (49.5%) and RMGIC (42.8%). The vitality and dentine repair capacity of the pulp is dependent on odontoblast survival. Variations in the extent of odontoblast injury caused during operative procedures, may be the major underlying reason for the success or failure of restorative treatments.

Human odontoblast cell numbers after dental injury

OBJECTIVES

The purpose of this study was to measure the changes in odontoblast cell numbers in response to cavity restoration variables and patient factors, and the effect these factors have on dental repair by tertiary dentinogenesis. The number of vital odontoblasts is a critical factor for pulpal repair following restorative surgery, and yet little information is available on these cell numbers.

METHODS

Class V non-exposed cavities were prepared in the buccal surface of intact first or second premolar teeth of 27 patients, between 9 and 17 years of age. Following tooth extraction (28-163 days) the area of reactionary dentine and the area of the odontoblasts were measured histomorphometrically.

RESULTS

Patient factors, as well as cavity preparation and restoration variables, had little effect on the numbers of odontoblasts per pulpal unit area. However, the age of the patient did appear to have an effect on the reactionary dentine secretory capacity of odontoblasts per unit area, and on the relative number of odontoblasts beneath cut dentinal tubules.

CONCLUSIONS

Odontoblast cell numbers were maintained following the preparation of cavities cut into dentine with a 0.5mm residual dentine thickness. The repair capacity of the pulp-dentine complex would appear to be age dependent, this may explain differences in the success of various restorative treatments between patients.