Influence of surface roughness and shape on microdamage of the osseous surface adjacent to titanium dental implants

Improving antibacterial ability of Ti-Cu thin films with co-sputtering method

Due to the resistance of some bacteria to antibiotics, research in the field of dealing with bacterial infections is necessary. A practical approach utilized in this study involves the preparation of an antibacterial thin film on the surfaces, which can effectively inhibit and reduce biofilm formation and bacterial adherence. In this study, we report the fabrication of bactericidal titanium (Ti) and copper (Cu) surfaces which involves a powerful co-sputtering method. This method provides a situation in which constituent elements are deposited simultaneously to control the composition of the thin film. Prepared samples were examined by energy-dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), X-ray diffraction (XRD), atomic force microscopy (AFM), and contact angle measurements. To evaluate antibacterial behavior, we used two bacterial strains Gram-negative Escherichia coli (E. coli) and Gram-positive Staphylococcus aureus (S. aureus). Antibacterial activity of the prepared sample was assessed by determining the number of colony-forming units per milliliter (CFU/ml) using a standard viable cell count assay. Results indicated that as the Cu concentration increased, the nanoscale surfaces became rougher, with roughness values rising from 11.85 to 49.65 nm, and the contact angle increased from 40 to 80 degrees, indicating a hydrophilic character. These factors play a significant role in the antibacterial properties of the surface. The Ti-Cu films displayed superior antibacterial ability, with a 99.9% reduction (equivalent to a 5-log reduction) in bacterial viability after 2 h compared to Ti alone against both bacterial strains. Field emission scanning electron microscopy (FE-SEM) images verified that both E. coli and S. aureus cells were physically deformed and damaged the bacterial cell ultrastructure was observed. These findings highlight that adding Cu to Ti can improve the antibacterial ability of the surface while inhibiting bacterial adherence. Therefore, the Ti14-Cu86 sample with the highest percentage of Cu had the best bactericidal rate. Investigation of toxicity of Cu-Ti thin films was conducted the using the MTT assay, which revealed their biocompatibility and absence of cytotoxicity, further confirming their potential as promising biomaterials for various applications.

Concentrations of co-administered vancomycin and meropenem in the internal dead space of a cannulated screw and in cancellous bone adjacent to the screw - Evaluated by microdialysis in a porcine model

BACKGROUND

Cannulated screws are often used in the management of open lower extremity fractures. These fractures exhibit broad contamination profiles, necessitating empirical Gram-positive and Gram-negative antibiotic coverage. To ensure full antibiotic protection of the cannulated screw and the bone tissue, it is generally accepted that target tissue antibiotic concentrations, as a minimum, reach and remain above relevant epidemiological cut-off minimal inhibitory concentrations (T>MIC) for a sufficient amount of time.

METHODS

8 female pigs were included. Microdialysis catheters were placed in the internal dead space of a cannulated screw placed in tibial cancellous bone, in tibial cancellous bone adjacent to the screw (mean distance to the screw: 3 mm), and in cancellous bone on the contralateral tibia. Following single-dose simultaneous intravenous administrations of vancomycin (1000 mg) and meropenem (1000 mg), microdialysates and plasma were dynamically sampled over 8 h. The applied MIC targets ranged from 1 to 4 µg/mL for vancomycin and 0.125-2 µg/mL for meropenem RESULTS: For both drugs, and for all MIC targets investigated (except for the high vancomycin target: 4 µg/mL), the internal dead space of the cannulated screw had the shortest T>MIC. At the low MIC targets T>MIC ranged between 88 and 449 min across sampling sites for vancomycin (1 µg/mL), and 148-406 min for meropenem (0.125 µg/mL). For the high MIC targets, T>MIC ranged between 3 and 446 min for vancomycin (4 μg/mL) and 17-181 min for meropenem (2 μg/mL). Vancomycin displayed longer T>MIC (2 and 4 μg/mL), higher area under the concentration time curve (AUC_0-last) and peak drug concentration in the proximal tibial cancellous bone without a screw nearby. For meropenem, only the cancellous bone AUC_0-last was significantly higher on the side with no screw.

CONCLUSION

We found short T>MIC, particularly for the high MIC targets for vancomycin and meropenem, both inside the cannulated screw and in cancellous bone adjacent to the screw. The presence of a cannulated screw impaired the penetration of especially vancomycin into cancellous bone adjacent to the screw. More aggressive or different vancomycin and meropenem approaches may be considered to encompass contaminating differences and to ensure a theoretically more sufficient antibiotic protection of cannulated screws when used in the management of open lower extremity fractures.

Effect of macrogeometry and bone type on insertion torque, primary stability, surface topography damage and titanium release of dental implants during surgical insertion into artificial bone

This study investigated the influence of implant macrogeometry and bone type on insertion torque (IT), primary stability (ISQ), surface topography damage, and the amount of titanium (Ti) released during insertion. Forty implants with different macrogeometries (Facility - Cylindrical with spiral-shaped threads; Alvim - Tapered with buttress-shaped threads) were inserted into artificial bone types I-II and III-IV. Surface morphology was evaluated by Scanning Electron Microscope (SEM) and roughness parameters with Laser Scanning Confocal Microscopy (LSCM) before and after insertion (AI). Implant macrogeometry was characterized by LSCM. The chemical composition of bone beds was determined by SEM associated with Energy Dispersive X-Ray Spectroscopy. The amount of Ti released was analyzed with Energy Dispersive X-Ray Fluorescence. Alvim had greater IT and ISQ than Facility. Bone types I-II require higher IT of implants. Alvim also had greater internal threads angle, higher initial roughness, and significant reduction of roughness AI, compared to Facility. The functional surface height reduced AI, especially in flank and valley of threads. Height of surface roughness of Alvim and Facility implants was similar AI. Implants surface morphology changes and metallic particles on bone beds were observed after implant insertion, mainly into bone types III-IV. Implants inserted into bone types I-II showed less surface damage. Alvim implants released more Ti (37.52 ± 25.03 ppm) than Facility (11.66 ± 28.55 ppm) on bone types III-IV. The implant macrogeometry and bone types affect IT, ISQ, surface damage, and Ti amount released during insertion. Alvim implants were more wear susceptible, releasing higher Ti concentration during insertion into bone types III-IV.

Histomorphometric analysis of implant osseointegration using hydrophilic implants in diabetic rats

OBJECTIVES

To evaluate peri-implant bone formation of titanium implants using an in vivo rat model with and without uncontrolled diabetes mellitus (DM) to evaluate osseointegration of hydrophobic (Neoporos®) and hydrophilic (Acqua®) surfaces.

MATERIALS AND METHODS

54 rats were divided into two groups: DM group (DMG) (streptozotocin-induced diabetes) and a control group (CG). Implants with hydrophobic (Neoporos®) and hydrophilic surfaces (Acqua®) were placed in the left or right tibia of animals. Animals were further divided into three groups (n = 9) euthanized after 7, 14, or 28 days. Bone-to-implant contact (BIC) and bone area fraction occupancy (BAFO) were assessed in total, cortical, and medullary areas.

RESULTS

The DMG group, after a 7-day healing period, yielded with the Acqua implants presented significantly higher total BIC (+37.9%; p=0.03) and trabecular BIC (%) (+46.3%; p=0.02) values in comparison to the Neoporos implants. After 28 days of healing, the CG yielded that the cortical BAFO of Acqua implants to be significantly, 14%, higher (p=0.04) than Neoporos implants.

CONCLUSION

The positive effects of the Acqua surface were able to counteract the adverse impact of uncontrolled DM at early osseointegration periods. After 28 days in vivo, the metabolic systemic impairment caused by DM overcame the surface treatment effect, leading to impaired osseointegration in both hydrophilic and hydrophobic implants.

CLINICAL RELEVANCE

The adverse effects of diabetes mellitus with respect to bone healing may be minimized by deploying implants with strategically modified surfaces. This study evaluated the effects of implants with Acqua® and Neoporos® surfaces in both diabetic and healthy animals. During the initial healing period in diabetic animals, the hydrophilic surface was demonstrated to have beneficial effect on osseointegration in comparison to the hydrophobic surface. The results provide an insight into early healing, but the authors suggest that a future short-term and long-term clinical study is needed to assess the possible benefit of the Acqua® implant as well as in increasing the predictability of implant osseointegration.

Insertion torque/time integral as a measure of primary implant stability

The goal of this in vitro study was to determine the insertion torque/time integral for three implant systems. Bone level implants (n = 10; BLT - Straumann Bone Level Tapered 4.1 mm × 12 mm, V3 - MIS V3 3.9 mm × 11.5 mm, ASTRA - Dentsply-Sirona ASTRA TX 4.0 mm × 13 mm) were placed in polyurethane foam material consisting of a trabecular and a cortical layer applying protocols for medium quality bone. Besides measuring maximum insertion torque and primary implant stability using resonance frequency analysis (RFA), torque time curves recorded during insertion were used for calculating insertion torque/time integrals. Statistical analysis was based on ANOVA, Tukey's honest differences test and Pearson product moment correlation (α = 0.05). Significantly greater mean maximum insertion torque (59.9 ± 4.94 Ncm) and mean maximum insertion torque/time integral (961.64 ± 54.07 Ncm∗s) were recorded for BLT implants (p < 0.01). V3 showed significantly higher mean maximum insertion torque as compared to ASTRA (p < 0.01), but significantly lower insertion torque/time integral (p < 0.01). Primary implant stability did not differ significantly among groups. Only a single weak (r = 0.61) but significant correlation could be established between maximum insertion torque and insertion torque/time integral (p < 0.01) when all data from all three implant groups were pooled. Implant design (length, thread pitch) seems to affect insertion torque/time integral more than maximum insertion torque.

Patient-specific in silico models can quantify primary implant stability in elderly human bone

Secure implant fixation is challenging in osteoporotic bone. Due to the high variability in inter- and intra-patient bone quality, ex vivo mechanical testing of implants in bone is very material- and time-consuming. Alternatively, in silico models could substantially reduce costs and speed up the design of novel implants if they had the capability to capture the intricate bone microstructure. Therefore, the aim of this study was to validate a micro-finite element model of a multi-screw fracture fixation system. Eight human cadaveric humerii were scanned using micro-CT and mechanically tested to quantify bone stiffness. Osteotomy and fracture fixation were performed, followed by mechanical testing to quantify displacements at 12 different locations on the instrumented bone. For each experimental case, a micro-finite element model was created. From the micro-finite element analyses of the intact model, the patient-specific bone tissue modulus was determined such that the simulated apparent stiffness matched the measured stiffness of the intact bone. Similarly, the tissue modulus of a small damage region around each screw was determined for the instrumented bone. For validation, all in silico models were rerun using averaged material properties, resulting in an average coefficient of determination of 0.89 ± 0.04 with a slope of 0.93 ± 0.19 and a mean absolute error of 43 ± 10 μm when correlating in silico marker displacements with the ex vivo test. In conclusion, we validated a patient-specific computer model of an entire organ bone-implant system at the tissue-level at high resolution with excellent overall accuracy. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:954-962, 2018.

A review of biomarkers in peri-miniscrew implant crevicular fluid (PMICF)

Background

The temporary anchorage devices (TADs) which include miniscrew implants (MSIs) have evolved as useful armamentarium in the management of severe malocclusions and assist in complex tooth movements. Although a multitude of factors is responsible for the primary and secondary stability of miniscrew implants, contemporary research highlights the importance of biological interface of MSI with bone and soft tissue in augmenting the success of implants.

The inflammation and remodeling associated with MSI insertion or loading are reflected through biomarkers in peri-miniscrew implant crevicular fluid (PMICF) which is analogous to the gingival crevicular fluid. Analysis of biomarkers in PMICF provides indicators of inflammation at the implant site, osteoclast differentiation and activation, bone resorption activity and bone turnover. The PMICF for assessment of these biomarkers can be collected non-invasively via paper strips, periopaper or micro capillary pipettes and analysed by enzyme-linked immunosorbent assay (ELISA) or immunoassays. The markers and mediators of inflammation have been previously studied in relation to orthodontic tooth movement include interleukins (IL-1β, IL-2, IL-6 and IL-8), growth factors and other proteins like tumour necrosis factor (TNF-α), receptor activator of nuclear factor kappa-B ligand (RANKL), chondroitin sulphate (CS) and osteoprotegerin (OPG).

Studies have indicated that successful and failed MSIs have different concentrations of biomarkers in PMICF. However, there is a lack of comprehensive information on this aspect of MSIs. Therefore, a detailed review was conducted on the subject.

Results

A literature search revealed six relevant studies: two on IL-1β; one on IL-2, IL-6 and IL-8; one on TNF-α; one on CS; and one on RANKL/OPG ratio. One study showed an increase in IL-1β levels upon MSI loading, peak in 24 hours (h), followed by a decrease in 21 days to reach baseline in 300 days. A 6.87% decrease in IL-2 levels was seen before loading and a 5.97% increase post-loading. IL-8 showed a 6.31% increase after loading and IL-6 increased by 3.08% before MSI loading and 15.06% after loading. RANKL/OPG ratio increased in loaded compared to unloaded MSIs.

Conclusions

Cytokines (mainly ILs and TNF-α) and RANKL/OPG ratio showed alteration in PMICF levels upon loading of MSIs as direct or indirect anchorage.

A novel in silico method to quantify primary stability of screws in trabecular bone

Insufficient primary stability of screws in bone leads to screw loosening and failure. Unlike conventional continuum finite-element models, micro-CT based finite-element analysis (micro-FE) is capable of capturing the patient-specific bone micro-architecture, providing accurate estimates of bone stiffness. However, such in silico models for screws in bone highly overestimate the apparent stiffness. We hypothesized that a more accurate prediction of primary implant stability of screws in bone is possible by considering insertion-related bone damage. We assessed two different screw types and loading scenarios in 20 trabecular bone specimens extracted from 12 cadaveric human femoral heads (N = 5 for each case). In the micro-FE model, we predicted specimen-specific Young's moduli of the peri-implant bone damage region based on morphometric parameters such that the apparent stiffness of each in silico model matched the experimentally measured stiffness of the corresponding in vitro specimen as closely as possible. The standard micro-FE models assuming perfectly intact peri-implant bone overestimated the stiffness by over 330%. The consideration of insertion related damaged peri-implant bone corrected the mean absolute percentage error down to 11.4% for both loading scenarios and screw types. Cross-validation revealed a mean absolute percentage error of 14.2%. We present the validation of a novel micro-FE modeling technique to quantify the apparent stiffness of screws in trabecular bone. While the standard micro-FE model overestimated the bone-implant stiffness, the consideration of insertion-related bone damage was crucial for an accurate stiffness prediction. This approach provides an important step toward more accurate specimen-specific micro-FE models. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:2415-2424, 2017.

Influence of femtosecond laser on the osteogenetic efficiency of polyetheretherketone and its composite

Objective:

This study aimed to evaluate the effect of a femtosecond laser on the osteogenetic efficiency of polyetheretherketone (PEEK) and its composite for clinical applications.

Methods:

One hundred pieces of PEEK and its composite (6 × 4 × 2 mm3) were randomly divided into four groups and treated as follows: group A1, PEEK; group A2, PEEK + femtosecond laser; group B1, PEEK composite; and group B2, PEEK composite + femtosecond. The surface morphology of the pieces of each group was observed through scanning electron microscopy. The surface roughness and wettability, which were considered as the main parameters affecting cell adhesion characteristics of implants, were measured. The animals whose mandibles were implanted with the four groups of materials were killed at the end of 6 and 12 weeks. Various characterization tests, such as Cone Beam Computed Tomography (CBCT), push-out test, microscope test, and bone implant contact , were conducted to investigate the healing effect between materials and bones.

Results:

In group B1, the nanoparticles in PEEK were uniformly distributed. In groups A2 and B2, many periodic nanostructures were observed. The surface roughness and wettability of group B2 were significantly increased compared to those of the other groups ( p < 0.05). At each time point, the number of trabecular bones, contact strength, and BIC of group B2 were higher than those of the three other groups ( p < 0.05). Compared with those of group A1, the test results of group B1 were significantly improved.

Conclusion:

Femtosecond lasers can effectively enhance the biological activity of PEEK and its composite; PEEK composite exhibits better biological activity than PEEK.

Evaluation of local cancellous bone amelioration by poly-L-DL-lactide copolymers to improve primary stability of dental implants: a biomechanical study in sheep

OBJECTIVES

The aim of this study was to evaluate the clinical performance of local cancellous bone amelioration by a 70:30 poly-(L-lactide-co-D,L-Lacide) copolymer with two different implant designs on primary stability and after 4 and 12 weeks of healing time.

MATERIAL AND METHODS

In six sheep, n = 36 implants (TH) with a conditioned, sandblasted, thermal acid-etched micro-rough surface and n = 36 implants (NB) with a highly crystalline and phosphate-enriched anodized titanium oxide surface were placed in the pelvic bone. Using an ultrasound-based process named Constant Amelioration Process (CAP), half of peri-implant trabecular bone structures were locally tested with 70:30 poly-(L-lactide-co-D,L-Lacide) copolymer in both implant groups, TH and NB. The CAP technology employs ultrasonic energy to liquefy 70:30 poly-(L-lactide-co-D,L-Lacide) which enters the inter-trabecular space, leading to local reinforcement of the cancellous bone structure after solidification of the copolymer. The CAP test group was compared with reference implants placed with the conventional site preparation according to the manufacturers' description. Primary stability was assessed by the measurement of torque-in values and implant stability quotient (ISQ; n = 18 per group). Secondary stability was analyzed by biomechanical removal torque testing after 4 and 12 weeks (n = 9 per group).

RESULTS

Insertion torque value (23.3 N cm ± 13.6) of reference TH implants demonstrated a statistically significant (P = 0.00) difference in comparison with test TH implants (41.9 N cm ± 19.5). Reference NB implants revealed a statistically significant (P = 0.03) lower insertion torque value (23.7 N cm ± 13.5) than test NB implants (39.7 N cm ± 18.6). ISQ values increased for all implants from initial implant placement until sacrifice at 12 weeks. Reference TH implants tended to result in an increase in torque values from 4 weeks (181.9 N cm ± 22.8) to 12 weeks (225.7 N cm ± 47.4). This trend could be also proven for implants of test sites (4 week: 176.8 N cm ± 24.1; 12 week: 201.5 N cm ± 53.4). For reference, NB implants a non-significant increase in removal torque values from 4 weeks (146. 7 N cm ± 18.0) to 12 weeks (170.2 N cm ± 40.4) was observed. Removal torque values of test NB implants did not increase from 4 weeks (153.3 N cm ± 21.5) to 12 weeks (146.1 N cm ± 37.5).

CONCLUSION

Biomechanical data proved significantly enhanced primary stability of dental implants after local amelioration without long-term sequelae and irrespective of implant design. After 4- and 12-week healing time, removal torque of locally test implants was as high as for control implants, and osseointegration was therefore not influenced by the CAP process. No correlation between ISQ values and torque values was found.

Comparison of two dental implant surface modifications on implants with same macrodesign: an experimental study in the pelvic sheep model

OBJECTIVES

The aim of this study was to compare two different surfaces of one uniform macro-implant design in order to focus exclusively on the osseointegration properties after 2, 4 and 8 weeks and to discuss the animal model chosen.

MATERIAL AND METHODS

In six mature sheep, n = 36 implants with a highly crystalline and phosphate-enriched anodized titanium oxide surface (TiU) and n = 36 implants with a hydrophilic, sandblasted, large grit and acid-etched surface (SLA) were placed in the pelvic bone. TiU implants were custom-made to match the SLA implant design. The implant stability and bone-to-implant contact (BIC) were assessed by resonance frequency (ISQ), backscatter scanning electron microscopy (B-SEM), light microscopy (LM), micro-CT and intravital fluorochrome staining. Biomechanical removal torque testing was performed.

RESULTS

Overall, no statistically significant differences in BIC total (trabecular + cortical) between TiU and SLA were found via LM and B-SEM. BIC values (B-SEM; LM) in both groups revealed a steady rise in trabecular bone attachment to the implant surface after 2, 4 and 8 weeks. In the 2- to 4-week time interval in the TiU group (P = 0.005) as well as in the SLA group (P = 0.01), a statistically significant increase in BIC trabecular could be observed via LM. B-SEM values confirmed the statistically significant increase for TiU (P = 0.001). In both groups, BIC trabecular values after 8 weeks were significantly higher (P ≤ 0.05) than after 2 weeks (B-SEM; LM). Biomechanical data confirmed the histological data.

CONCLUSION

The two surfaces proved comparable osseointegration in this sheep model.

Assessing bone's adaptive capacity around dental implants: a literature review

BACKGROUND

Increased stress (force) on prostheses induces strain (deformation) in the peri-implant bone. Elevated stress and strain could result in the failure of implants that support prostheses. However, the survival rate of implants supporting prostheses under increased stress is high. Either the bone is stronger than expected or it adapts to increased stress. Concepts regarding bone's adaptive capacity continue to evolve and are the focus of this literature review.

TYPES OF STUDIES REVIEWED

The authors searched the literature to find studies that addressed the bone's capacity to adjust to increased stress and strain. They assessed experimental and clinical trials in which investigators monitored healing after placement of dental implants.

RESULTS

The data indicate that forces greater than the bone's adaptive ability can induce loss of osseointegration, as well as osseous resorption. In contrast, it is possible that increased stress on prostheses initiates a reparative process, thereby facilitating retention of implants experiencing increased stress. Numerous lines of evidence support the concept that bone can modify itself to withstand increased mechanical forces.

PRACTICAL IMPLICATIONS

The authors provide an explanation for the high success rate of prostheses and implants in bone that are exposed to increased stress and strain.

Potential risk of asymptomatic osteomyelitis around mandibular third molar tooth for aged people: a computed tomography and histopathologic study

The purpose of this study was to explore the relationship between bone mineral density and histopathological features of mandibular alveolar bone evaluated quantitatively by Hounsfield units [HU] and by histopathology in human subjects. Fifty-six mandibular molars were extracted in 50 patients. Computed tomography was obtained preoperatively, and a cortical bone biopsy was obtained on the extracted sites for histopathological evaluation. The mean cortical and cancellous bone radiodensity was 1846 ± 118 HU and 926 ± 436 HU, respectively. There was no correlation between age and cortical bone HU (r = -0.004, P = 0.976); however, the correlation between age and cancellous bone HU was significant (r = 0.574, P<0.0000). Significant differences in the cancellous bone between young (0-30 years), middle (31-60 years) and old patient groups (61< years) were evident (P<0.05), whereas the cortical bone presented no significant differences. The histopathological evaluation showed that the young patient group had relatively few osteomyelitis, whereas the old patient group showed 100% focal sclerotic osteomyelitis regardless of the fact that the patients had no clinical symptoms. The mean osteocyte number/unit bone area was 170.7 ± 82.2. Negative correlation between age and osteocyte number was significant (r = -0.51, P<0.0001). Mean lacunae numbers/unit cortical bone area were 413.1 ± 130 with non-significant negative correlation (r = -0.257, P = 0.056). The mean empty lacunae numbers/cortical bone were 242.5±145, with no correlation (r = 0.081, P = 0.559). The young patients had high osteocyte number, whereas the old patients showed reduction of the osteocytes in the cortical bone (P < 0.05). Bone quality might correlate better to viable cell numbers, which influenced the osseous healing. It is suggested that the outermost layer of cortical bone may have lost its cellular activities over the years due to chronic infection, which may have provoked sclerotic changes in the cancellous bone around tooth.

Histological and biomechanical analysis of porous additive manufactured implants made by direct metal laser sintering: a pilot study in sheep

OBJECTIVES

It was the aim of this study to analyze osseointegrative properties of porous additive manufactured titanium implants made by direct metal laser sintering in a sheep model after an implantation period of 2 and 8 weeks.

MATERIAL AND METHODS

Three different types of implants were placed in the pelvis of six sheep. In each sheep were placed three standard machined (M), three sandblasted and etched (SE), and three porous additive manufactured (AM) implants. Of these three implants (one per type) were examined histologically and six implants were tested biomechanically. Additionally a semiquantitative histomorphometrical and qualitative fluorescent microscopic analysis were performed.

RESULTS

After 2 and 8 weeks bone-to-implant-contact (BIC) values of the AM surface (2w: 20.49% ± 5.18%; 8w: 43.91% ± 9.69%) revealed no statistical significant differences in comparison to the M (2w: 20.33% ± 11.50%; 8w: 25.33% ± 4.61%) and SE (2w: 43.67 ± 12.22%; 8w: 53.33 ± 8.96%) surfaces. AM surface showed the highest increase of the BIC between the two observation time points. Considering the same implantation period histomorphometry and fluorescent labelling disclosed no significant differences in the bone surrounding the three implants groups. In contrast Removal-torque-test showed a significant improve in fixation strength (P ≤ 0.001) for the AM (1891.82 ± 308, 44 Nmm) surface after eight weeks in comparison to the M (198.93±88,04 Nmm) and SE (730.08 ± 151,89 Nmm) surfaces.

CONCLUSION

All three surfaces (M, SE, and AM) showed sound osseointegration. AM implants may offer a possible treatment option in clinics for patients with compromised bone situations.

Three-dimensional morphology of microdamage in peri-screw bone: a scanning electron microscopy of methylmethacrylate cast replica

Screw implantation inevitably causes microdamage in surrounding bone. However, little is known about the detailed characteristics of microdamage in peri-screw bone. In this study, we developed a method to construct microdamage cast with methylmethacrylate (MMA) and observed the cast using scanning electron microscopy (SEM). In basic fuchsin stained bone sections observed by bright-field and fluorescence microscopy, diffuse damage, cross-hatched damage, and linear cracks were all presented in peri-screw bone. Using MMA casting/SEM method, we found numerous densely packed microcracks in the areas with diffuse damage. The osteocyte canaliculi and the microcracks consisting of diffuse damage had a similar diameter (or width), usually <0.5 μm, but their morphology was largely different. In the area with cross-hatched damage, the orientation of microcracks was similar to that in diffuse damage, but the number was significantly decreased. Many microcracks were thicker than 1 μm and associated with a rough surface. Large linear cracks (∼10 μm in diameter) occurred in different areas. Plenty of microcracks were present on the surface of some linear cracks. In conclusion, the MMA casting/SEM method can demonstrate the three-dimensional morphology of different types of microdamage, particularly the microcracks in diffuse damage, which are unable to be shown by light microscopy.

Bone damage associated with orthodontic placement of miniscrew implants in an animal model

INTRODUCTION

The purposes of this study were to quantify bone damage associated with insertion of 2 types of miniscrew implants and to relate the amount of bone damage to monocortical plate thickness.

METHODS

Nondrilling (n = 28) and self-drilling (n = 28) miniscrew implants (6 × 1.6 mm, Dentaurum, Newtown, Pa), and pilot holes (n = 26) were placed bilaterally in the maxillae and the mandibles of 5 adult dogs immediately after death. Bone blocks were cut, bulk stained with 1% basic fuchsin, embedded in methyl methacrylate, sectioned, and mounted. Monocortical plate thickness was measured adjacent to the miniscrew implant insertion site. Damage amounts were quantified at distances of 0 to 0.5 mm (adjacent region) and 0.5 to 1 mm (distant region) from the bone-implant interface. Total fractional damaged area (%), fractional microcracked area (%), and fractional diffuse damaged area (%) were quantified by using standard histomorphometric methods.

RESULTS

The mean monocortical plate thickness of the specimens from the mandible (2.2 mm) was significantly (P <0.001) greater than that of the maxillary specimens (0.9 mm). In the mandible, the 3 damage parameters were greater with self-drilling miniscrew implants than with nondrilling miniscrew implants; however, there were no differences in the damage parameters in the maxilla.

CONCLUSIONS

Bone damage accumulation is related to the type of miniscrew implant and the thickness of the bone.