Selective removal of dental caries with a diode-pumped Er:YAG laser

LED-pumped Er:Cr:YSGG light sources

For, what we believe is, the first time, an Er:Cr:YSGG crystal is pumped by LEDs through a Ce:YAG luminescent concentrator. We demonstrate both laser emission at 2.79 µm and strong spontaneous emission at 1.6 µm. The luminescent concentrator delivers 1.5 ms pulses at 10 Hz in the visible (550-650 nm) to the Er:Cr:YSGG crystal, in a transverse pumping configuration. The Er:Cr:YSGG laser produces up to 6.8 mJ at 2.79 µm in a biconcave cavity. The Er:Cr:YSGG also stands out as a bright broadband incoherent source around 1.6 µm with a unique combination of peak power (351 mW) and brightness (1.4 W/sr/cm2).

Selective removal of dental calculus with a diode-pumped Er:YAG laser

Selective removal of dental calculus with high precision is best accomplished using lasers operating at high pulse repetition rates focused to a small spot size to limit damage to sound tissues. Conventional flash-lamp pumped Er:YAG lasers are poorly suited for this purpose, but new diode-pumped solid state (DPSS) Er:YAG lasers have become available operating at high pulse repetition rates. The purpose of this study was to determine if image-guided laser ablation can be used to selectively remove calculus from tooth surfaces with minimal damage to the underlying sound cementum and dentin. A DPSS Er:YAG laser system was used to selectively remove calculus from ten extracted teeth using sequential SWIR images at 1500-1750-nm. The selectivity of removal was assessed using digital microscopy and optical coherence tomography. Calculus was removed with minimal damage to the underlying sound cementum and dentin.

Use of a DPSS Er:YAG laser for the selective removal of composite from tooth surfaces

New diode-pumped solid state (DPSS) Er:YAG lasers have become available operating at high pulse repetition rates. These lasers are ideally suited for integration with laser scanning systems for the selective removal of dental decay and composite restorative materials from tooth surfaces. The purpose of this study was to determine if a DPSS Er:YAG laser system is suitable for the selective removal of composite from tooth surfaces. Relative ablation rates of composite and enamel were determined and composite was removed from tooth surfaces using a DPSS Er:YAG laser. Composite was removed very rapidly with ablation rates approaching 50-µm per pulse. A fluence of ~50 J/cm² appeared optimal for the removal of composite and damage to the enamel was limited to less than 100-µm after the removal of composite as thick as 700-800-µm; however, dentin is removed at similar rates to composite. The DPSS Er:YAG laser appears to be better suited for the removal of composite than conventional flash-lamp pumped Er:YAG lasers since composite is ablated at higher rates than dental enamel and the high pulse repetition rates enable greater selectivity while maintaining high removal rates.

Selective removal of natural caries lesions from dentin and tooth occlusal surfaces using a diode-pumped Er:YAG laser

Selective removal of caries lesions with high precision is best accomplished using lasers operating at high pulse repetition rates utilizing small spot sizes. Conventional flash-lamp pumped Er:YAG lasers are poorly suited for this purpose, but new diode-pumped solid-state (DPSS) Er:YAG lasers have become available operating at high pulse repetition rates. Microradiography was used to determine the mineral content of the demineralized dentin of 200-μm thick sections with natural caries lesions prior to laser ablation. The purpose of this study was to explore the use of a DPSS Er:YAG laser for the selective removal of demineralized dentin and natural occlusal lesions on extracted teeth.

Microindentation hardness and calcium/phosphorus ratio of dentin following excavation of dental caries lesions with different techniques

BACKGROUND

The aim of this in vitro study was to evaluate the microindentation hardness and chemical composition of residual dentin left at the cavity bottom following removal of carious dentin using the Carisolv chemomechanical and Er:YAG laser caries excavation methods in comparison with the conventional tungsten-carbide bur excavation.

METHODS

Sixty-nine extracted permanent teeth with occlusal dentin caries were assigned into three groups according to caries removal technique. Carious dentin excavation was guided by tactile method and a caries-staining dye. In stereomicroscope images (100×) of the samples, the presence or absence of residual caries was defined. The Knoop hardness value of the cavity floor was determined and atomic analysis of treated cavities was performed by energy dispersive X-ray spectroscopy.

RESULTS

The Knoop hardness value of residual dentin left at the cavity bottom was lower (One-way ANOVA, Dunnett-C, p < 0.05) and the percentage of samples with remaining carious dentin was higher after Carisolv excavation than those obtained after conventional and laser excavations (Kruskal-Wallis, Mann-Whitney U, p < 0.05). No significant differences were found between the quantities of calcium content (Ca wt%), phosphorus content (P wt%) and calcium/phosphorus ratio of the cavities treated by three techniques (Kruskal-Wallis, Mann-Whitney U, p > 0.05).

CONCLUSION

The results indicated that Er:YAG laser was more comparable to conventional bur excavation than chemomechanical method in the efficacy of caries removal with regard to microindentation hardness of remaining dentin and both Carisolv gel and Er:YAG laser did not alter chemical composition of residual dentin in the treated cavities.

Selective removal of dental composite with a diode-pumped Er:YAG laser

Selective removal of dental composite with high precision is best accomplished using lasers operating at high pulse repetition rates focused to a small spot size. Conventional flash-lamp pumped Er:YAG lasers are poorly suited for this purpose, but new diode-pumped Er:YAG lasers have become available operating at high pulse repetition rates. The purpose of this study was to compare the ablation rates and selectivity of enamel and composite for a 30 W diode-pumped Er:YAG laser operating with a pulse duration of 30-50-μs and evaluate it's suitability for the selective removal of composite from tooth surfaces. The depth of ablation and changes in surface morphology were assessed using digital microscopy. The fluence range of 30-50 J/cm² appeared optimal for the removal of composite, and damage to sound enamel was limited to less than 100-μm after the removal of composite as thick as 700-800-μm. Future studies will focus on the use of methods of feedback to further increase selectivity.