Aesthetic Rehabilitation of a Patient with Bruxism Using Ceramic Veneers and Overlays Combined with Four-Point Monolithic Zirconia Crowns for Occlusal Stabilization: A 4-Year Follow-Up

Effect of preparation design and endodontic access on fracture resistance of zirconia overlays in mandibular molars: An in vitro study

PURPOSE

To evaluate the fracture resistance of zirconia overlays, considering various preparation designs and the presence of endodontic access.

MATERIALS AND METHODS

Ninety translucent zirconia (5Y-PSZ) overlay restorations were divided into six groups (n = 15/group) based on different preparation designs, with and without endodontic access: chamfer margin 4 mm above the gingival level without (group 1) and with endodontic access (group 2); margin 2 mm above the gingival level without (group 3) and with endodontic access (group 4); overlay with no chamfer margin without (group 5) and with endodontic access (group 6). Restorations were bonded to mandibular first molar resin dies, and the groups with endodontic access were sealed with flowable resin composite. All restorations underwent 100,000 cycles of thermal cycling between 5°C and 55°C, followed by loading until fracture. Maximum load and fracture resistance were recorded. ANOVA with Tukey post-hoc tests were used for statistical comparison (α < 0.05).

RESULTS

Fracture resistance significantly varied among overlay designs with and without endodontic access (p < 0.001), except for the no-margin overlays (groups 5 and 6). Overlays with a 2 mm margin above the gingival margin with endodontic access (group 4) exhibited significantly higher fracture resistance compared to both the 4-mm supragingival (group 2) and no-margin (group 6) designs, even when compared to their respective intact groups (groups 1 and 5). There were no significant differences between the no-margin and 4-mm supragingival overlays.

CONCLUSION

The more extensive zirconia overlay for mandibular molars is the first choice since the 2 mm margin above the gingival level design withstood considerable loads even after undergoing endodontic access. A no-margin overlay is preferred over the 4-mm supragingival design as it preserves more tooth structure and there was no outcome difference, irrespective of endodontic access. Caution is warranted in interpreting these findings due to the in vitro nature of the study.

Transforming smiles: Aesthetic rehabilitation with layered zirconia veneers and crowns for spaced dentition and faulty crowns-A case report

The objective of this case report was to provide a plan for aesthetic rehabilitation of a patient utilizing layered zirconia restorations to produce a homogeneous, pleasing smile. In this case, a female patient, aged 38 years, presented in dental clinic with a spaced dentition and faulty crowns that were causing functional and aesthetic concerns. She was a banker by profession and socially active. The treatment plan involved layered zirconia indirect restorations to enhance her natural teeth appearance. The aim of this case report was to propose an effective strategy for addressing her concerns, with the potential to achieve a desired aesthetic outcome. Additionally, the implementation of this treatment approach had a positive influence on self-esteem and confidence of the patient.

Semidirect Resin Composite Veneers in a Patient with Bruxism

This case report details the esthetic rehabilitation of a 32-year-old male patient suffering from sleep bruxism, primarily manifesting as a fracture and significant loss of tooth structure in the anterior maxillary central incisors. To address these concerns, the patient underwent a restorative treatment involving the application of semidirect resin composite veneers on the maxillary incisors and direct resin composite restoration on the incisal regions of the maxillary canines. This approach not only restored the functional integrity of the teeth but also significantly enhanced the patient's esthetic appearance.

Rehabilitation of a deep bite patient with worn dentition using minimally invasive approach: A 3-year follow-up

Full mouth rehabilitation of severely worn teeth represents a challenging situation for dental clinicians. This case report describes the minimally invasive interdisciplinary approach for treatment of severely worn dentition with a loss of vertical dimension of occlusion. After 3 years of follow-up, no complication was observed.

Silane Heat Treatment Could Eliminate the Hydrofluoric Acid Etching of Lithium Disilicate Overlays: A Four-Year Follow-Up

A four-year follow-up of a novel silane heat treatment method for bonding lithium disilicate overlays to tooth structures without hydrofluoric acid etching of the ceramic surface is presented in this case report. Silane heat treatment modifies the silane layer and thus enhances resin ceramic bond strength without hydrofluoric acid etching. The standard ceramic preparation technique prior to bonding silicate ceramics to tooth structure is hydrofluoric acid etching and applying a silane coupling agent, followed by dental adhesive. In this case, the micromechanical roughening of the ceramic surface was performed by air abrasion with Al₂O₃. Silane heat treatment with constant 120°C airflow, applied for 60 sec, followed by dental adhesive application enhanced the resin-ceramic bond strength. After a four-year follow-up, the restorations' clinical appearance could be defined as excellent/very good according to the FDI clinical criteria for the evaluation of direct and indirect restorations. This clinical result supports many in vitro studies regarding the resin-ceramic bond strength and durability obtained through postsilanization heat treatment.