Development of a subject-standing-type cone-beam computed tomography for chest and orthopedic imaging

The way we were (and how we got here): fifty years of technology changes in dental and maxillofacial radiology

The history of the last 50 years (1970-2020) of technological changes and progresses for equipment and procedures in dental and maxillofacial radiology is related from the insider perspective of an industrial physicist and technologist who has been instrumental at innovating and developing medical equipment in different parts of the world. The onset and improvement of all major categories of dental and maxillofacial radiographic equipment is presented, from the standpoint of their practical acceptance and impact among common dentists and maxillofacial radiologists: X-ray sources and detectors for intraoral radiography, and panoramic systems, both film-based and digital (including photo-stimulated phosphor plates); and cone beam CT.

Accuracy and reliability of cone-beam computed tomography for measuring alveolar bone height and detecting bony dehiscences and fenestrations

INTRODUCTION

The purpose of this study was to evaluate the accuracy and reliability of cone-beam computed tomography (CBCT) in the diagnosis of naturally occurring fenestrations and bony dehiscences. In addition, we evaluated the accuracy and reliability of CBCT for measuring alveolar bone margins.

METHODS

Thirteen dry human skulls with 334 teeth were scanned with CBCT technology. Measurements were made on each tooth in the volume-rendering mode from the cusp or incisal tip to the cementoenamel junction and from the cusp or incisal tip to the bone margin along the long axis of the tooth. The accuracy of the CBCT measurements was determined by comparing the means, mean differences, absolute mean differences, and Pearson correlation coefficients with those of direct measurements. Accuracy for detection of defects was determined by using sensitivity and specificity. Positive and negative predictive values were also calculated.

RESULTS

The CBCT measurements showed mean deviations of 0.1 +/- 0.5 mm for measurements to the cementoenamel junction and 0.2 +/- 1.0 mm to the bone margin. The absolute values of the mean differences were 0.4 +/- 0.3 mm for the cementoenamel junction and 0.6 +/- 0.8 mm for the bone margin. The sensitivity and specificity of CBCT for fenestrations were both about 0.80, whereas the specificity for dehiscences was higher (0.95) and the sensitivity lower (0.40). The negative predictive values were high (>or=0.95), and the positive predictive values were low (dehiscence, 0.50; fenestration, 0.25). The reliability of all measurements was high (r >or=0.94).

CONCLUSIONS

By using a voxel size of 0.38 mm at 2 mA, CBCT alveolar bone height can be measured to an accuracy of about 0.6 mm, and root fenestrations can be identified with greater accuracy than dehiscences.

Using a flat-panel detector in high resolution cone beam CT for dental imaging

OBJECTIVES

Cone beam CT (CBCT) requires a two-dimensional X-ray detector. In the several CBCT systems developed for dental imaging, detection has been by the combination of an X-ray image intensifier and charge-coupled device (CCD) camera. In this paper, we propose a new CBCT system in which the detector is of the flat-panel type and evaluate its performance in dental imaging.

METHODS

We developed a prototype CBCT that has a flat-panel-type detector. The detector consists of a CsI scintillator screen and a photosensor array. First, the flat panel detector and image intensifier detector were compared in terms of the signal-to-noise ratio (SNR) of projected images. We then used these data and a theoretical formula to evaluate noise in reconstructed images. Second, reconstructed images of a bar pattern phantom were obtained as a way of evaluating the spatial resolution. Then, reconstructed images of a skull phantom were obtained.

RESULTS

The SNR of the developed system was 1.6 times as high as that of a system with an image intensifier detector of equal detector pitch. The system was capable of resolving a 0.35 mm pattern and its field of view almost completely encompassed that of an image intensifier detector which is used in dentomaxillofacial imaging. The fine spatial resolution of the detector led to images in which the structural details of a skull phantom were clearly visible.

CONCLUSIONS

The system's isotropically fine resolution will lead to improved precision in dental diagnosis and surgery. The next stage of our research will be the development of a flat panel detector system with a high frame acquisition rate.

Characteristics of a newly developed dentomaxillofacial X-ray cone beam CT scanner (CB MercuRay): system configuration and physical properties

OBJECTIVE

The purpose of this paper is to present the system configuration and physical properties of a new dentomaxillofacial X-ray cone beam CT system (CB MercuRay) being developed.

METHODS

The system consists of an image intensifier and a cone beam X-ray source. There are two different models of this system, each with a different size image intensifier, 9" or 12". Each system has three field of view (FOV) modes. The 12" system has facial (F), panoramic (P) and implant (I) FOV modes. The 9" system has P, I and dental (D) modes. Images produced by these systems consist of 512 x 512 x 512 isotropic voxels. Physical properties such as resolution, noise and distortion of the images were evaluated in this study. Modulation transfer function (MTF) was measured using Boone's method. Image noise was measured as the standard deviation of the CT value in water. Circularity of the axial images yielded by the two models was measured using an 8 mm diameter acrylic pipe phantom.

RESULTS

The resolving power at a MTF of 0.1 in the D mode was over 2.0 lp mm(-1), suggesting that this system yields images of high resolution. The standard deviation of the CT value in water was approximately 80, which is thought to be greater than that of conventional CT. The circularity of images of the pipe phantom was 99% of the ideal value.

CONCLUSION

This study shows that our newly developed cone beam CT system produces high resolution three-dimensional volumetric images that will be useful for the examination of dentomaxillofacial disorders.