3D Graphene Oxide Hydrogel Derived from Waste Toner as Adsorbent

A new strategy for utilization of gasification ash: Manganese oxides-modified activated carbon for efficient copper citrate removal

To address the challenges posed by solid waste generated from coal gasification ash, a pyrolysis self-activation method was employed to prepare activated carbon by gasification ash, followed by the modification with manganese oxide to enhance its adsorption performance. Subsequently, the removal efficiency and mechanism for copper citrate were investigated. The results demonstrated the successful preparation of manganese oxides modified gasification ash-derived activated carbon (GAC-MnOx), exhibiting a specific surface area of 158.3 m2/g and a pore volume of 0.1948 cm³/g. The kinetic process could be described by the pseudo-second-order kinetic model (R2 = 0.958). High removal efficiency and low concentration of dissolved Mn were observed within the pH range of 3-10, where the adsorption capacity of GAC-MnOx for copper citrate exhibited an inverse relationship with pH. Notably, the fitting results of the Langmuir model demonstrated that the maximum adsorption capacity of GAC-MnOx for copper citrate is determined to be 7.196 mg/g at pH 3. The adsorption capacity of GAC-MnOx was found to be significantly reduced to 0.26 mg/g as the pH decreased below 2, potentially attributed to the dissolution of Mn. The findings of the Dual-Mode model demonstrated that the copper citrate removal mechanism by GAC-MnOx involved both surface adsorption and precipitation processes as follows: the porous structure of activated carbon enables physical adsorption of copper citrate, the MnOx or oxygen-containing functional groups establish chemical bonds with copper citrate and subsequently precipitate onto the surface of the adsorbent. The physical adsorption remains predominant in the removal of copper citrate, despite a gradual decrease in its proportion with increasing pH and equilibrium concentrations. Moreover, the X-ray photoelectron spectroscopy results indicated that copper citrate might be oxidized by MnOx to release copper ions and be retained on the surface of the adsorbent, meaning the adsorption efficiency of Cu(II)-Cit by GAC was enhanced through MnOx oxidation. This study could provide a new strategy for the high-value resource utilization of gasification ash.

Transformation of Waste Toner Powder into Valuable Fe2O3 Nanoparticles for the Preparation of Recyclable Co(II)-NH2-SiO2@Fe2O3 and Its Applications in the Synthesis of Polyhydroquinoline and Quinazoline Derivatives

Ecological recycling of waste materials by converting them into valuable nanomaterials can be considered a great opportunity for management and fortification of the environment. This article deals with the environment-friendly synthesis of Fe₂O₃ nanoparticles (composed of α-Fe₂O₃ and γ-Fe₂O₃) using waste toner powder (WTP) via calcination. Fe₂O₃ nanoparticles were then coated with silica using TEOS, functionalized with silane (APTMS), and immobilized with Co(II) to get the desired biocompatible and cost-effective catalyst, i.e., Co(II)-NH₂-SiO₂@Fe₂O₃. The structural features in terms of evaluation of morphology, particle size, presence of functional groups, polycrystallinity, and metal content over the surface were determined by Fourier transform infrared spectroscopy (FTIR), powder X-ray diffraction (P-XRD), field emission gun-scanning electron microscopy (FEG-SEM), energy-dispersive X-ray analysis (EDX), high resolution-transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), vibrating sample magnetometry (VSM), Brunauer-Emmett-Teller (BET) analysis, and inductively coupled plasma-atomic emission spectroscopy (ICP-AES) studies. XPS confirmed the (II) oxidation state of Co, and ICP-AES and EDX supported the loading of Co(II) over the surface of the support. P-XRD proved the polycrystalline nature of the Fe₂O₃ core and even after functionalization. In comparison to previously reported methods, Co(II)-NH₂-SiO₂@Fe₂O₃ provides an eco-friendly procedure for the synthesis of polyhydroquinoline and quinazoline derivatives with several advantages such as a short reaction time and high yield. Polyhydroquinoline and quinazoline derivatives are important scaffolds in pharmacologically active compounds. Moreover, the developed nanocatalyst was recyclable, and HR-TEM and P-XRD confirmed the agglomeration in the recycled catalyst resulted in a decrease in yield after the fifth run. The present protocol provides a new strategy of recycling e-waste into a heterogeneous nanocatalyst for the synthesis of heterocycles via multicomponent reactions. This made the synthesized catalyst convincingly more superior to other previously reported catalysts for organic transformations.

Graphene and graphene-based materials in axonal repair of spinal cord injury

Graphene and graphene-based materials have the ability to induce stem cells to differentiate into neurons, which is necessary to overcome the current problems faced in the clinical treatment of spinal cord injury. This review summarizes the advantages of graphene and graphene-based materials (in particular, composite materials) in axonal repair after spinal cord injury. These materials have good histocompatibility, and mechanical and adsorption properties that can be targeted to improve the environment of axonal regeneration. They also have good conductivity, which allows them to make full use of electrical nerve signal stimulation in spinal cord tissue to promote axonal regeneration. Furthermore, they can be used as carriers of seed cells, trophic factors, and drugs in nerve tissue engineering scaffolds to provide a basis for constructing a local microenvironment after spinal cord injury. However, to achieve clinical adoption of graphene and graphene-based materials for the repair of spinal cord injury, further research is needed to reduce their toxicity.

Waste Egg Tray and Toner-Derived Highly Efficient 3D Solar Evaporator for Freshwater Generation

With the advancement of civilization, water purification, as well as management and disposal of ever-increasing municipal solid waste (MSW), and e-waste, have become global concerns. To address these issues in a sustainable way, a 3D solar evaporator has been proposed in this paper by repurposing recycled paper from MSW in the form of egg trays and waste dry toner (e-waste) using a facile fabrication method. The unique 3D porous structure, fibrous surface, superior water absorbing capability as well as low thermal conductivity of wastepaper-derived egg trays make them an excellent candidate for an efficient solar evaporator, while the waste toner powder coating significantly enhances the optical absorbance capacity. Under 1 sun illumination, the proposed solar evaporator demonstrates an excellent evaporation rate and efficiency of 1.3 kg/m² h and 78.5%, respectively. Moreover, the competitive advantage of the 3D structure in collecting solar irradiance at various light incident angles in comparison to a 2D structure, excellent cycle stability, low processing temperature, and the use of low-cost waste materials enable its use for large-scale water purification systems.