Haemolysis induced by mechanical circulatory support devices: unsolved problems

Since the use of continuous flow blood pumps as ventricular assist devices is standard, the problems with haemolysis have increased. It is mainly induced by shear stress affecting the erythrocyte membrane. There are many investigations about haemolysis in laminar and turbulent blood flow. The results defined as threshold levels for the damage of erythrocytes depend on the exposure time of the shear stress, but they are very different, depending on the used experimental methods or the calculation strategy. Here, the results are resumed and shown in curves. Different models for the calculation of the strengths of erythrocytes are discussed. There are few results reported about tests of haemolysis in blood pumps, but some theoretical approaches for the design of continuous flow blood pumps according to low haemolysis have been investigated within the last years.

In Vivo and in Vitro Experience with the PUCA-II, a Single-Valved Pulsatile Catheter-Pump

The Pulsatile Catheter (PUCA) pump is a trans-arterial pulsatile ventricular assist device that can be used for short-term left ventricular support. The separate inflow and outflow valves in the first version of the device (PUCA-I) were replaced by a single inflow/outflow valve in the latest PUCA pump version (PUCA-II). The new combined valve was tested during in vitro (mock circulation) and in vivo experiments for valve leakage, flow resistance, and thrombus formation. During the in vitro experiments a maximum valve leakage of 6% during ejection and 21% during aspiration was found. The maximum flow resistance coefficient (K) was 4. The animal experiments demonstrated that the PUCA-II could be positioned within a few minutes into the left ventricle without X-ray guidance and without using a vascular graft. Thrombi were not found in the combined valve after total pump time of 3 hours, which proved the good washout of the valve. Initial experiments to position the pump in the right ventricle through the pulmonary artery were successful and contributed to the development of a new application for the device.

Numerical Simulation of the Influence of a Left Ventricular Assist Device on the Cardiovascular System

The PUCA (pulsatile catheter) pump is a left ventricular assist device (LVAD) capable of unloading the left ventricle (LV) and improving coronary flow by providing a counterpulsation effect. It consists of an extracorporeal located membrane pump, coupled to a transarterial catheter that enters the body via a superficial artery and ends in the LV. Blood is aspirated from the LV and pumped in the ascending aorta through the same catheter guided by a valve system. Timing and frequency of the PUCA pump influence its efficacy. To study the influence of several pump parameters a numerical model of the device and the circulatory system has been developed. Results of animal experiments were used to validate the model.

Optimization studies resulted in a pump configuration with a stroke volume of 50 cc and pump:heart frequency mode of 1:2 that starts ejection at the beginning of diastole.

Design and test of a vascular access device

Transarterial left ventricular assist devices (LVADs), such as the Hemopump, IABP, and PUCA-pump, are meant to be introduced into the body via the femoral or axillary artery without major surgery. For certain applications, introduction is performed directly into the aorta via an open thorax procedure. A prototype of a vascular access device has been realized that allows direct access into the aorta as an alternative for the common surgical graft anastomosis suturing technique. The device consists of a metal tube acting as a circular knife to cut a hole in the aortic wall, a screw to store the removed part of the aortic wall, and a plastic tube that is introduced through the hole and tightly connected to the aortic wall. The device could be placed without aortic clamping. The device has been tested on a slaughterhouse porcine aorta. A low-pressurized aorta appeared to be the worst case; thus, two animal experiments in the low-pressurized pulmonary artery were performed. No leakage occurred for pressures between 40 and 300 mm Hg.

Numerical simulation of the pulsating catheter pump: A left ventricular assist device

The pulsating catheter (PUCA) pump, a left ventricular assist device, consists of a hydraulically or pneumatically driven membrane pump, extracorporeally placed and mounted to a valved catheter. The catheter is introduced into an easily accessible artery and positioned with its distal tip in the left ventricle. Blood is aspirated from the left ventricle during systole and ejected into the ascending aorta during diastole. A numerical model of the PUCA pump has been developed to determine the internal diameter of the PUCA pump catheter that allows a certain blood flow. The model considers a limitation of mechanical blood damage and determines the accompanying pressure and flow profile for driving the pump. For a flow of 5 L/min, a catheter with an internal diameter of at least 6. 95 mm is required. For 3 L/min, the minimal diameter is 5.50 mm. The latter catheter can be introduced in the axillary artery, the former via the aorta during an open thorax surgical procedure. To validate the numerical model, 2 different PUCA pump configurations were tested in vitro. Results showed a good resemblance between model and in vitro behavior of the PUCA pump.