Porcine acellular lung matrix for wound healing and abdominal wall reconstruction: A pilot study

Remodeling and Regenerative Properties of Fully Absorbable Meshes for Abdominal Wall Defect Repair: A Systematic Review and Meta-Analysis of Animal Studies

Fully absorbable meshes can repair abdominal wall defects and effectively reduce the incidence of complications, but different types of fully absorbable meshes have different remodeling and regeneration effects. In order to investigate and compare the effects of different fully absorbable meshes on remodeling and regeneration in animals and reduce the biological risk of clinical translation, SYRCLE was adopted to evaluate the methodological quality of the included studies, and GRADE and ConQual were used to evaluate the quality of evidence. According to the inclusion and exclusion criteria, a total of 22 studies related to fully absorbable meshes were included in this systematic review. These results showed that fiber-based synthetic materials and fiber-based natural materials exhibited better restorative and regenerative effects indicated by infiltration and neovascularization, when compared with a porcine acellular dermal matrix. In addition, the human acellular dermal matrix was found to have a similar regenerative effect on the host extracellular matrix and scaffold degradation compared to the porcine acellular dermal matrix, porcine intestinal submucosa, and fiber-based natural materials, but it offered higher tensile strength than the other three. The quality of the evidence in this field was found to be poor. The reasons for downgrading were analyzed, and recommendations for future research included more rigor in study design, more transparency in result reporting, more standardization of animal models and follow-up time for better evaluation of the remodeling and regenerative performance of abdominal wall hernia repair meshes, and less biological risk in clinical translation.

Acellular dermal matrix decorated with collagen-affinity peptide accelerate diabetic wound healing through sustained releasing Histatin-1 mediated promotion of angiogenesis

Treating diabetic ulcers is a major challenge in clinical practice, persecuting millions of patients with diabetes and increasing the medical burden. Recombinant growth factor application can accelerate diabetic wound healing via angiogenesis. The local administration of recombinant growth factors has no robust clinical efficiency because of the degradation of append short duration of the molecules in the hostile inflammatoryenvironment.The present study focused on the pathophysiology of impaired neovascularization and growth factor short duration in the diabetic wound. We prepared a collagen-binding domain (CBD)-fused recombinant peptide (C-Histatin-1) that had both pro-angiogenesis capacity and collagen-affinity properties. Next, we created a biocompatible acellular dermal matrix (ADM) as a drug delivery carrier that featured collagen-richness, high porosity, and non-cytotoxicity. C-Histatin-1 was then tethered on ADM to obtain a sustained-release effect. Finally, a functional scaffold (C-Hst1/ADM) was developed. C-Hst1/ADM can sustain-release Histatin-1 to promote the adhesion, migration, and angiogenesisof vascular endothelial cells in vitro. Using a diabetic wound model, we showed that C-Hst1/ADM could significantly promote angiogenesis, reduce scar widths, and improve extracellular collagen accumulation. Therefore, the results of this study provide a foundation for the clinical application of C-Hst1/ADM covering scaffold in the treatment of diabetic wounds.

Decellularized Tissues for Wound Healing: Towards Closing the Gap Between Scaffold Design and Effective Extracellular Matrix Remodeling

The absence or damage of a tissue is the main cause of most acute or chronic diseases and are one of the appealing challenges that novel therapeutic alternatives have, in order to recover lost functions through tissue regeneration. Chronic cutaneous lesions are the most frequent cause of wounds, being a massive area of regenerative medicine and tissue engineering to have efforts to develop new bioactive medical products that not only allow an appropriate and rapid healing, but also avoid severe complications such as bacterial infections. In tissue repair and regeneration processes, there are several overlapping stages that involve the synergy of cells, the extracellular matrix (ECM) and biomolecules, which coordinate processes of ECM remodeling as well as cell proliferation and differentiation. Although these three components play a crucial role in the wound healing process, the ECM has the function of acting as a biological platform to permit the correct interaction between them. In particular, ECM is a mixture of crosslinked proteins that contain bioactive domains that cells recognize in order to promote migration, proliferation and differentiation. Currently, tissue engineering has employed several synthetic polymers to design bioactive scaffolds to mimic the native ECM, by combining biopolymers with growth factors including collagen and fibrinogen. Among these, decellularized tissues have been proposed as an alternative for reconstructing cutaneous lesions since they maintain the complex protein conformation, providing the required functional domains for cell differentiation. In this review, we present an in-depth discussion of different natural matrixes recently employed for designing novel therapeutic alternatives for treating cutaneous injuries, and overview some future perspectives in this area.

Amniotic fluid allograft enhances the host response to ventral hernia repair using acellular dermal matrix

Ventral hernia repair (VHR) with acellular dermal matrix (ADM) has high rates of recurrence that may be improved with allogeneic growth factor augmentation such as amniotic fluid allograft (AFA). We hypothesized that AFA would modulate the host response to improve ADM incorporation in VHR. Lewis rats underwent chronic VHR with porcine ADM alone or with AFA augmentation. Tissue harvested at 3, 14, or 28 days was assessed for region-specific cellularity, and a validated histomorphometric score was generated for tissue incorporation. Expression of pro-inflammatory (Nos1, Tnfα), anti-inflammatory (Arg1, Il-10, Mrc1) and tissue regeneration (Col1a1, Col3a1, Vegf, and alpha actinin-2) genes were quantified using quantitative reverse-transcription polymerase chain reaction. Amniotic fluid allograft treatment caused enhanced vascularization and cellularization translating to increased histomorphometric scores at 14 days, likely mediated by upregulation of pro-regeneration genes throughout the study period and molecular evidence of anti-inflammatory, M2-polarized macrophage phenotype. Collectively, this suggests AFA may have a therapeutic role as a VHR adjunct.

Platforms to test the temporospatial capabilities of carrier systems in delivering growth factors to benefit vascular bioengineering

In this study we produced a set of in vitro culture platforms to model vascular cell responses to growth factors and factor delivery vehicles. Two of the systems (whole vessel and whole lung vascular development) were supported by microfluidic systems facilitating media circulation and waste removal. We assessed vascular endothelial growth factor (VEGF) delivery by Pluronic F-127 hydrogel, 30 nm pore-sized microparticles (MPs), 60 nm pore-sized MP or a 50/50 mixture of 30 and 60 nm pore-sized MP. VEGF was delivered to porcine acellular lung vascular scaffolds (2.5 cm² square pieces or whole 3D segments of acellular blood vessels) as well as whole acellular lung scaffolds. Scaffold-cell attachment was examined as was vascular tissue formation. We showed that a 50/50 mixture of 30 and 60 nm pore-sized silicon wafer MPs allowed for long-term release of VEGF within the scaffold vasculature and supported vascular endothelial tissue development during in vitro culture.

Sterilization and disinfection methods for decellularized matrix materials: Review, consideration and proposal

Sterilization is the process of killing all microorganisms, while disinfection is the process of killing or removing all kinds of pathogenic microorganisms except bacterial spores. Biomaterials involved in cell experiments, animal experiments, and clinical applications need to be in the aseptic state, but their physical and chemical properties as well as biological activities can be affected by sterilization or disinfection. Decellularized matrix (dECM) is the low immunogenicity material obtained by removing cells from tissues, which retains many inherent components in tissues such as proteins and proteoglycans. But there are few studies concerning the effects of sterilization or disinfection on dECM, and the systematic introduction of sterilization or disinfection for dECM is even less. Therefore, this review systematically introduces and analyzes the mechanism, advantages, disadvantages, and applications of various sterilization and disinfection methods, discusses the factors influencing the selection of sterilization and disinfection methods, summarizes the sterilization and disinfection methods for various common dECM, and finally proposes a graphical route for selecting an appropriate sterilization or disinfection method for dECM and a technical route for validating the selected method, so as to provide the reference and basis for choosing more appropriate sterilization or disinfection methods of various dECM.

•

Asepsis is the prerequisite for the experiment and application of biomaterials.

•

Sterilization or disinfection affects physic-chemical properties of biomaterials.

•

Mechanism, advantages and disadvantages of sterilization or disinfection methods.

•

Factors influencing the selection of sterilization or disinfection methods.

•

Selection of sterilization or disinfection methods for decellularized matrix.

The application possibility of acellular dermal matrix decorated with nano-silver in the reconstruction of contaminated abdominal wall

Acellular dermal matrix (ADM) is a biomaterial, which commonly used for repair of tissue defects; however, infection is the main factor underlying the failure of treatments involving ADM. To enhance the anti-infection ability of ADM, we constructed a new form of ADM that was decorated with nano-silver ('NS-ADM'). The introduction of nano-silver did not destroy the decellularized structure of ADM, and no significant difference was detected with regards to the maximum tensile force when compared between NS-ADM and ADM (P = 0.351). NS-ADM was not cytotoxic to cell growth when the concentration of nano-silver solution ≤ 25 ppm and exhibited strong antibacterial activity in vitro. Besides, when rats were inoculated with 10⁴ CFU/mL, there were significantly lower bacterial counts in the NS-ADM group than in the ADM group when assessed seven days after surgery (P = 0.047); no significant differences were detected on days 14 and 28. Although there were no significant differences in bacterial counts on days 7, 14, or 21 between the two groups (rats were inoculated with 10⁶ CFU/mL), the number of rats showing reduced bacterial counts or clearing was higher in the NS-ADM group than in the ADM group. Rats that were inoculated with 10⁸ CFU/mL showed repair failure. Overall, NS-ADM is a promising antibacterial biomaterial for repairing contaminated soft-tissue defects, in which antibacterial properties are superior to ADM. The antibacterial activity of NS-ADM was limited for severe infections, and further in vivo studies are needed to evaluate its efficacy and biosafety.

One-year follow-up study of iBTA-induced allogenic biosheet for repair of abdominal wall defects in a beagle model: a pilot study

PURPOSE

We evaluated the usefulness of biosheet, an in-body tissue-engineered collagenous membrane, as a novel repair material for abdominal wall defects in a beagle model.

METHODS

Biosheets were prepared by embedding molds into subcutaneous pouches in two beagle dogs for 2 months, with subsequent storage in 70% ethanol. The obtained biosheets (thickness 0.5 mm, size 25 cm²) were implanted to replace same-size defects in the abdominal wall of two beagles in an allogenic manner.

RESULTS

The biosheets were not stressed during suturing and did not split; moreover, patch implantation into the defective wound was easy. No complications such as anastomotic leaks or infections occurred during implantation. One year post-implantation, the thickness of the biosheet implantation section increased to approximately 2.5 mm, corresponding to approximately 70% of the native abdominal wall. A section of the abdominal wall muscle elongated from the periphery of the newly formed collagen layer, and the peritoneum was entirely formed on the peritoneal cavity surface, resulting in partial regeneration of the three-layered abdominal wall. The mechanical strength of the newly formed wall was approximately fivefold higher than the native wall. The elasticity of the biosheet in the low-strain region decreased to approximately 10% post-implantation, similar to the native wall.

CONCLUSIONS

This pilot study demonstrated that biosheet maintained the abdominal wall without any complications for 1 year post-implantation, and partial regeneration was observed. Although this experiment was limited to two cases, the results indicated that biosheet may serve as a reliable abdominal wall restorative material.

How to build a lung: latest advances and emerging themes in lung bioengineering

Chronic respiratory diseases remain a major cause of morbidity and mortality worldwide. The only option at end-stage disease is lung transplantation, but there are not enough donor lungs to meet clinical demand. Alternative options to increase tissue availability for lung transplantation are urgently required to close the gap on this unmet clinical need. A growing number of tissue engineering approaches are exploring the potential to generate lung tissue ex vivo for transplantation. Both biologically derived and manufactured scaffolds seeded with cells and grown ex vivo have been explored in pre-clinical studies, with the eventual goal of generating functional pulmonary tissue for transplantation. Recently, there have been significant efforts to scale-up cell culture methods to generate adequate cell numbers for human-scale bioengineering approaches. Concomitantly, there have been exciting efforts in designing bioreactors that allow for appropriate cell seeding and development of functional lung tissue over time. This review aims to present the current state-of-the-art progress for each of these areas and to discuss promising new ideas within the field of lung bioengineering.

Biomaterials and Culture Technologies for Regenerative Therapy of Liver Tissue

Regenerative approach has emerged to substitute the current extracorporeal technologies for the treatment of diseased and damaged liver tissue. This is based on the use of biomaterials that modulate the responses of hepatic cells through the unique matrix properties tuned to recapitulate regenerative functions. Cells in liver preserve their phenotype or differentiate through the interactions with extracellular matrix molecules. Therefore, the intrinsic properties of the engineered biomaterials, such as stiffness and surface topography, need to be tailored to induce appropriate cellular functions. The matrix physical stimuli can be combined with biochemical cues, such as immobilized functional groups or the delivered actions of signaling molecules. Furthermore, the external modulation of cells, through cocultures with nonparenchymal cells (e.g., endothelial cells) that can signal bioactive molecules, is another promising avenue to regenerate liver tissue. This review disseminates the recent approaches of regenerating liver tissue, with a focus on the development of biomaterials and the related culture technologies.