Using self-drilling screws in volar plate osteosynthesis for distal radius fractures: a feasibility study

Extensor Tendon Injury After Volar Locking Plating for Distal Radius Fractures: A Systematic Review

Distal radius fractures are common orthopedic injuries. Treatment has varied historically, but volar locking plating currently predominates. Although flexor tendon injury is a well-studied complication of this operation, extensor tendon injury is less well studied. The purpose of this review is to search the literature and present the epidemiology, presentation, and treatment of this complication. The Cochrane, EMBASE, PubMed, and SCOPUS databases were searched for the terms "volar" + "radius" + ("plate" OR "plating") + "extensor." Ninety final studies were included for analysis in this review. The incidence of extensor tendon rupture varies from 0% to 12.5%; the extensor pollicis longus is most commonly ruptured. The presentation and management of extensor tendon injury after injury, intraoperatively, and postoperatively are summarized. Radiographic views are described to detect screw prominence and minimize intraoperative risk. Extensor tendon injury after volar locking plate for distal radius fractures is an uncommon injury with several risk factors including dorsal screw prominence and fracture fragments. Removal of hardware and tendon transfers or reconstruction may be necessary to prevent loss of extensor mechanism.

Power-Tool Use in Orthopaedic Surgery: Iatrogenic Injury, Its Detection, and Technological Advances: A Systematic Review

Power tools are an integral part of orthopaedic surgery but have the capacity to cause iatrogenic injury. With this systematic review, we aimed to investigate the prevalence of iatrogenic injury due to the use of power tools in orthopaedic surgery and to discuss the current methods that can be used to reduce injury.

Distal radius fracture fixation using volar plate: A comparative study evaluating the biomechanical behavior of uni and bicortical distal screws

Extensor tendon ruptures caused by bicortical screws impingement following distal radius fracture fixation with volar plates are extensively reported in the literature. Thus, a biomechanical study comparing unicortical and bicortical fixations in intra-articular distal radius fracture models is critical in decision-making regarding distal radius fracture management. Forty-two synthetic radius models were fixed using a variable angle volar distal locking plate with seven screws. They were divided into 6 groups (n = 7): G1/G3/G4 unicortical fixation (75% of anteroposterior distal radius lenght); G2/G4/G6 bicortical fixation. Each group underwent a different mechanical test: axial compression (G1/G2), dorsal flexion (G3/G4), and volar flexion (G5/G6). The load application rate was 5 mm/min and 1000 cycles of 50 to 250 N at 1 Hz were performed between both static tests. Comparative results in the first static test, in the second static test, and in failure generally showed a very similar behavior. Models depicted similar behavior in the second static test when cyclic load was performed. Therefore, one can realize that stiffness differed during dorsal flexion only in the first static test. Maximum force to break the model in axial compression was greater in bicortical than in unicortical construct. Since biomechanical properties are similar, we recommend using unicortical distal locking screws in distal radius fracture fixation with volar plates to prevent extensor tendon ruptures.

Towards optimization of volar plate fixations of distal radius fractures: Using finite element analyses to reduce the number of screws

BACKGROUND

Using fewer distal screws in volar plate fixation of distal radius fractures could reduce treatment costs and complications. However, there is currently no consensus on the ideal screw configuration, likely due to experimental limitations and its subject-specific nature. In this study, finite element analysis was used to investigate (1) if reducing the number of screws is biomechanically feasible and (2) if an optimal screw configuration is subject-specific.

METHODS

Validated subject-specific finite element models of 16 human radii with extra articular distal radius fractures and volar plate fixation with six distal screws were used as a baseline. 41 additional configurations with three to six distal screws were simulated for each subject. Axial stiffness and peri-implant strains around the distal screws were evaluated. Subject-specific optimum configurations were determined using a lower bound for the axial stiffness and minimizing peri-implant strains.

FINDINGS

Even using three distal screws led to only minor deterioration of the biomechanical properties in the best configuration (axial stiffness: -11.2%, peri-implant strains: -35.0%), but a considerable deterioration in the worst configuration (axial stiffness: -46.2%, peri-implant strains: +112.4%). The optimization showed that the ideal screw configuration is subject-specific and on average 1.9 screws could be saved based on the herein used optimization criterion.

INTERPRETATION

This study highlights that not only how many, but which screws are used in volar plate fixation of distal radius fractures is critical. Using a patient-specific selection of distal screws bears potential to save costs and reduce complications.

Computerized anatomy of the distal radius and its relevance to volar plating, research, and teaching

Distal radius fractures are common and fracture patterns and fixation can be complex. Computerized anatomy evaluation (CAE) might offer non-invasive and enhanced anatomy assessment that might help with implant selection and placement and screw length determination. Our goal was to test the accuracy of two CAE methods for anatomical volar plate positioning and screw lengths measurement of the distal radius. We included 56 high-resolution peripheral quantitative computed tomography scans of intact, human distal radii. Plates were placed manually onto 3D printed models (method 1), which was compared with automated computerized plate placement onto the 3D computer models (method 2). Subsequently, screw lengths were determined digitally for both methods. Screw lengths evaluations were compared via Bland-Altman plots. Both CAE methods resulted in identical volar plate selection and in anatomical plate positioning. For screw length the concordance correlation coefficient was ≥0.91, the location shift ≤0.22 mm, and the scale shift ≤0.16. The differences were smaller than ±1 mm in all samples. Both CAE methods allow for comparable plate positioning and subsequent screw length measurement in distal radius volar plating. Both can be used as a non-invasive teaching environment for volar plate fixation. Method 2 even offers fully computerized assessments. Future studies could compare our models to other anatomical areas, post-operative volar plate positioning, and model performance in actual distal radius fracture instead of intact radii. Clin. Anat. 32:361-368, 2019. © 2018 The Authors. Clinical Anatomy published by Wiley Periodicals, Inc. on behalf of American Association of Clinical Anatomists.