Hybrid blade and locking plate fixation for proximal humerus fractures: a comparative biomechanical analysis

Lateral Wall Integrity of the Greater Tuberosity Is Important for the Stability of Osteoporotic Proximal Humeral Fractures After Plate Fixation

BACKGROUND

Previous studies assessing surgical fixation of osteoporotic proximal humeral fractures have primarily focused on medial calcar support. In this study, we utilized a specific model for 2-part surgical neck fracture of the osteoporotic proximal humerus to investigate how severe comminution of the greater tuberosity (GT) lateral wall affects biomechanical stability after fixation with a plate.

METHODS

Ten matched pairs of cadaveric humeri (right and left) were assigned to either a surgical neck fracture alone (the SN group) or a surgical neck fracture with GT lateral wall comminution (the LW group) with use of block randomization. We removed 5 mm of the lateral wall of the GT to simulate severe comminution of the lateral wall. Axial compression stiffness, torsional stiffness, varus bending stiffness, and the single load to failure in varus bending were measured for all plate-bone constructs.

RESULTS

Compared with the SN group, the LW group showed a significant decrease in all measures, including torsional stiffness (internal, p = 0.007; external, p = 0.007), axial compression stiffness (p = 0.002), and varus bending stiffness (p = 0.007). In addition, the mean single load to failure in varus bending for the LW group was 62% lower than that for the SN group (p = 0.005).

CONCLUSIONS

Severe comminution of the GT lateral wall significantly compromised the biomechanical stability of osteoporotic, comminuted humeral surgical neck fractures.

CLINICAL RELEVANCE

Although the generalizability of this cadaveric model may be limited to the extreme clinical scenario, the model showed that severe comminution of the GT lateral wall significantly compromised the stability of osteoporotic humeral surgical neck fractures fixed with a plate and screws alone.

Dynamic biomechanical investigation of a novel sulcus bicipitalis plate in combination with a conventional locking plate for the treatment of complex proximal humerus fractures

BACKGROUND

Complex proximal humerus fractures place high demands on osteosynthetic treatment. In some cases, double plating has already been used to increase primary stability of the osteosynthesis. This approach was advanced in the present study by developing an additive plate for the sulcus bicipitalis. To demonstrate the superior primary stability of the newly developed plate osteosynthesis, a biomechanical comparison against a conventional locking plate with an additional calcar screw was performed.

METHODS

Ten pairs of cadaveric humeri were treated proximally with a locking plate (PENTA plate small fragment, INTERCUS). Each had a two-part fracture model with a fracture gap of 10 mm. All right humeri were treated with an additive novel plate that extends along the bicipital sulcus and encircles the lesser tuberosity proximally. First, the specimens were loaded sinusoidally at 250 N in 20° abduction for 5000 cycles. Afterwards quasi-static loading until failure was applied.

FINDINGS

The movement at the fracture gap due to the cyclic loading occurred mainly as rotation around the z-axis, corresponding to a tilt medially and distally. The double plate osteosynthesis reduces the rotation by approximately 39%. For all load cycles observed, except 5000 cycles, medial and distal rotation of the head was significantly reduced by the double plate. The failure loads showed no significant differences between the groups.

INTERPRETATION

In the tested scenario under cyclic loading, the novel double plate osteosynthesis showed a significant superiority of primary stability over the conventional treatment with one locking plate. Furthermore, the study showed the advantages of cyclic load application over quasi-static load application until failure.

Catastrophic failure of a titanium locking plate in a proximal humeral fracture: case report and literature review

Background

Angular stable locking plates have shown good clinical results in treating proximal humeral fractures, but complications are not uncommon. This study reported a rare case of catastrophic failure of a titanium locking plate. A retrieval analysis of the implants was performed using an optic microscope and a scanning electron microscope.

Case presentation

A 69-year-old male reported a right proximal humeral fracture at the surgical neck and was treated by open reduction and internal fixation with a locking plate system. Ninety-six days after surgery, the patient came to clinic for acute local pain over the shoulder without any trauma. The radiographs showed a complete breakage of the implant accompanying displaced fracture. Revision surgery was performed to restabilize the fracture with a longer locking plate. The follow-up radiographs at 9 months showed complete union of the bone fracture.

Conclusions

From the retrieval analysis, repetitive torsion loads on the vulnerable area of the implant are assumed to cause this catastrophic event. It is recommended that adequate activity restriction, such as reaching, be undertaken to avoid this rare complication. Current study also provides contributive information for the modification of plate design and pre-operative planning for device configuration to improve the success rate of locking plate fixation.

Comparison of locking plates and intramedullary nails in treatment of three-part or four-part proximal humeral neck fractures in elderly population: A randomized trial protocol

BACKGROUND

Locking plate and intramedullary nail are two commonly applied methods to fix proximal humeral fractures. There are limited randomized studies that specifically evaluate the results of proximal humeral neck fractures with three-part or four-part treated by locking plates or intramedullary nails. Our goal was to compare functional outcomes, complications, and imaging features between the two groups.

METHODS

This single-center, prospective, randomized controlled test will be conducted in Tengzhou Central People's Hospital. Patients with these conditions will be included: age between 55 and 80 years; are able to communicate normally and agree to participate in our study; with the radiological evidence of proximal humeral fractures with three-part or four-part; surgical treatment was performed within twenty-one days after the acute fracture. Consecutive patients with proximal humeral fractures will be stochastic to be dealt with a locking plate or a bone nail. The informed consent will be acquired in each patients. Two groups will use the same postoperative rehabilitation protocol. Clinical outcomes include Intraoperative blood loss, operation time, Constant-Murley score, Disability, Arm, Shoulder and Hand score, shoulder range of motion (such as external rotation), and postoperative complications. The significance level was defaulted as P < .05.

RESULTS

This study will provide a solid theoretical basis for exploring which technique is better in treatment of 3-part or 4-part proximal humeral neck fractures in elderly population.

TRIAL REGISTRATION

This study protocol was registered in Research Registry (number: researchregistry6047).

Recent Trends, Technical Concepts and Components of Computer-Assisted Orthopedic Surgery Systems: A Comprehensive Review

Computer-assisted orthopedic surgery (CAOS) systems have become one of the most important and challenging types of system in clinical orthopedics, as they enable precise treatment of musculoskeletal diseases, employing modern clinical navigation systems and surgical tools. This paper brings a comprehensive review of recent trends and possibilities of CAOS systems. There are three types of the surgical planning systems, including: systems based on the volumetric images (computer tomography (CT), magnetic resonance imaging (MRI) or ultrasound images), further systems utilize either 2D or 3D fluoroscopic images, and the last one utilizes the kinetic information about the joints and morphological information about the target bones. This complex review is focused on three fundamental aspects of CAOS systems: their essential components, types of CAOS systems, and mechanical tools used in CAOS systems. In this review, we also outline the possibilities for using ultrasound computer-assisted orthopedic surgery (UCAOS) systems as an alternative to conventionally used CAOS systems.

Biomechanical comparison of screw-based zones of a spatial subchondral support plate for proximal humerus fractures

Stabilisation of proximal humerus fractures remains a surgical challenge. Spatial subchondral support (S3) plate promises to overcome common complications associated with conventional proximal humerus plates. This study compared the biomechanical performance of S3 plate with a fixed-angle hybrid blade (Equinoxe Fx) plate and a conventional fixed-angle locking plate (PHILOS). The effects of removal of different S3 plate screws on the humeral stability were also investigated. A total of 20 synthetic left humeri were osteotomised transversely at the surgical neck to simulate a two-part fracture and were each treated with an S3 plate. Head screws were divided into three zones based on their distance from the fracture site. Specimens were divided into four equal groups where one group acted as a control with all screws and three groups had one of the screw zones missing. With humeral head fixed, humeral shaft was first displaced 5 mm in extension, flexion, valgus and varus direction (elastic testing) and then until 30 mm varus displacement (plastic testing). Load-displacement data were recorded to determine construct stiffness in elastic tests and assess specimens' varus stability under plastic testing. Removal of the screw nearest to the fracture site led to a 20.71% drop in mean elastic varus bending stiffness. Removal of the two inferomedial screw above it resulted in a larger drop. The proximal screw pair had the largest contribution to extension and flexion bending stiffness. Varus stiffness of S3 plate constructs was higher than PHILOS and Fx plate constructs. Stability of humeri treated with S3 plate depends on screws' number, orientation and location. Varus stiffness of S3 plate construct (10.54 N/mm) was higher than that of PHILOS (6.61 N/mm) and Fx (7.59 N/mm) plate constructs. We attribute this to S3 plates' thicker cross section, the 135° inclination of its screws with respect to the humeral shaft and the availability of pegs for subchondral support.