A novel artificial vertebral implant with Gyroid porous structures for reducing the subsidence and mechanical failure rate after vertebral body replacement

Design and study of additively manufactured Three periodic minimal surface (TPMS) structured porous titanium interbody cage

Objective

TPMS porous structures have adjustable stiffness, a smooth surface, and highly connected pores, which help avoid stress concentration within the dot-matrix structure and promote cell adhesion and proliferation. A cervical interbody cage based on this type of porous structure was designed and fabricated, and its mechanical properties and biocompatibility were evaluated.

Methods

TPMS porous structures have adjustable stiffness, a smooth surface, and highly connected pores, which help avoid stress concentration within the dot-matrix structure and promote cell adhesion and proliferation. A cervical interbody cage based on this type of porous structure was designed and fabricated, and its mechanical properties and biocompatibility were evaluated.

Results

The volume fraction of the 3D-printed TC4-based Tubular-G structure was linearly related to compressive strength. Adjusting the volume fraction resulted in a Tubular-G structure with a modulus and yield strength similar to human bone, without stress concentration within the structure. The designed and fabricated TC4-based Tubular-G porous cervical interbody cage demonstrated excellent anti-sagging properties and biocompatibility.

Conclusions

The volume fraction of the 3D-printed TC4-based Tubular-G structure was linearly related to compressive strength. Adjusting the volume fraction resulted in a Tubular-G structure with a modulus and yield strength similar to human bone, without stress concentration within the structure. The designed and fabricated TC4-based Tubular-G porous cervical interbody cage demonstrated excellent anti-sagging properties and biocompatibility.

Porous versus solid shoulder implants in humeri of different bone densities: A finite element analysis

Porous metallic prosthesis components can now be manufactured using additive manufacturing techniques, and may prove beneficial for promoting bony ingrowth, for accommodating drug delivery systems, and for reducing stress shielding. Using finite element modeling techniques, 36 scenarios (three porous stems, three bone densities, and four held arm positions) were analysed to assess the viability of porous humeral stems for use in total shoulder arthroplasty, and their resulting mechanobiological impact on the surrounding humerus bone. All three porous stems were predicted to experience stresses below the yield strength of Ti6Al4V (880 MPa) and to be capable of withstanding more than 10 million cycles of each loading scenario before failure. There was an indication that within an 80 mm region of the proximal humerus, there would be a reduction in bone resorption as stem porosity increased. Overall, this study shows promise that these porous structures are mechanically viable for incorporation into permanent shoulder prostheses to combat orthopedic infections.

Parametric Design of Porous Structure and Optimal Porosity Gradient Distribution Based on Root-Shaped Implants

Porous structures can reduce the elastic modulus of implants, decrease stress shielding, and avoid bone loss in the alveolar bone and aseptic loosening of implants; however, there is a mismatch between yield strength and elastic modulus as well as biocompatibility problems. This study aimed to investigate the parametric design method of porous root-shaped implants to reduce the stress-shielding effect and improve the biocompatibility and long-term stability and effectiveness of the implants. Firstly, the porous structure part was parametrically designed, and the control of porosity gradient distribution was achieved by using the fitting relationship between porosity and bias and the position function of bias. In addition, the optimal distribution law of the porous structure was explored through mechanical and hydrodynamic analyses of the porous structure. Finally, the biomechanical properties were verified using simulated implant-bone tissue interface micromotion values. The results showed that the effects of marginal and central porosity on yield strength were linear, with the elastic modulus decreasing from 18.9 to 10.1 GPa in the range of 20-35% for marginal porosity, with a maximum decrease of 46.6%; the changes in the central porosity had a more consistent effect on the elastic modulus, ranging from 18.9 to 15.3 GPa in the range of 50-90%, with a maximum downward shift of 19%. The central porosity had a more significant effect on permeability, ranging from 1.9 × 10-7 m2 to 4.9 × 10-7 m2 with a maximum enhancement of 61.2%. The analysis showed that the edge structure had a more substantial impact on the mechanical properties. The central structure could increase the permeability more effectively. Hence, the porous structure with reasonable gradient distribution had a better match between mechanical properties and flow properties. The simulated implantation results showed that the porous implant with proper porosity gradient distribution had better biomechanical properties.