HPMC/PVP Dissolving Microneedles: a Promising Delivery Platform to Promote Trans-Epidermal Delivery of Alpha-Arbutin for Skin Lightening

Minoxidil Nanosuspension-Loaded Dissolved Microneedles for Hair Regrowth

Minoxidil (MIN) is used topically to treat alopecia. However, its low absorption limits its use, warranting a new strategy to enhance its delivery into skin layers. The objective of this study was to evaluate the dermal delivery of MIN by utilizing dissolved microneedles (MNs) loaded with MIN nanosuspension (MIN-NS) for hair regrowth. MIN-NS was prepared by the solvent-antisolvent precipitation technique. The particle size of MIN-NS was 226.7 ± 9.3 nm with a polydispersity index of 0.29 ± 0.17 and a zeta potential of -29.97 ± 1.23 mV. An optimized formulation of MIN-NS was selected, freeze-dried, and loaded into MNs fabricated with sodium carboxymethyl cellulose (Na CMC) polymeric solutions (MIN-NS-loaded MNs). MNs were evaluated for morphology, dissolution rate, skin insertion, drug content, mechanical properties, ex vivo permeation, in vivo, and stability studies. MNs, prepared with 14% Na CMC, were able to withstand a compression force of 32 N for 30 s, penetrate Parafilm M® sheet at a depth of 374-504 µm, and dissolve completely in the skin within 30 min with MIN %recovery of 95.1 ± 6.5%. The release of MIN from MIN-NS-loaded MNs was controlled for 24 h. MIN-NS-loaded MNs were able to maintain their mechanical properties and chemical stability for 4 weeks, when kept at different storage conditions. The in vivo study of the freeze-dried MIN-NS and MIN-NS-loaded MNs proved hair regrowth on rat skin after 11 and 7 days, respectively. These results showed that MIN-NS-loaded MNs could potentially improve the dermal delivery of MIN through the skin to treat alopecia.

Targeted intradermal delivery of alpha-arbutin-loaded dissolving polymeric microneedles visualized by three-dimensional Orbitrap secondary ion mass spectrometry (3D OrbiSIMS)

Hyperpigmentation, a prevalent dermatological condition characterized by melanin overproduction, poses treatment challenges due to the hydrophilicity of alpha-arbutin, a widely utilized tyrosinase inhibitor. This study investigates the efficacy of dissolving microneedles (DMNs) in augmenting skin permeation for alpha-arbutin delivery to the targeted epidermal site. Porcine full-thickness skin was employed in a 24-hour Franz cell study, commencing with the assessment of commercial alpha-arbutin-containing products. Solid steel microneedles (CMNs) from Dermapen® were utilized as both pre- and post-treatment modalities to evaluate the influence of different applications on alpha-arbutin delivery. Additionally, alpha-arbutin-loaded polyvinylpyrrolidone-co-vinyl acetate (PVPVA) DMNs, containing 2 % w/w alpha-arbutin, were fabricated and examined for their permeation-enhancing capabilities. HPLC analysis and 3D Orbitrap Secondary Ion Mass Spectrometry (OrbiSIMS) were employed to quantify and visualize alpha-arbutin in various Franz cell components. Results indicate that alpha-arbutin permeation to the skin was restricted (less than 1 %) without microneedle application and significantly increased by 6-fold (4-5 %) with post-treatment CMNs and DMNs, but not with pre-treatment CMNs. Notably, DMNs exhibited a more sustainable and robust capacity than post-treatment CMNs. OrbiSIMS imaging analysis revealed that DMNs visually enhance skin permeation of alpha-arbutin by delivering the compound to the basal layer of the targeted skin location. Overall, this study underscores the potential of DMNs as a promising delivery system for promoting targeted intradermal delivery of alpha-arbutin, providing a comprehensive exploration of various methodologies to identify innovative and improved microneedle approaches for alpha-arbutin permeation.

Natural herb wormwood-based microneedle array for wound healing

Artemisia argyi, commonly known as wormwood, is a traditional Chinese herbal food and medicine celebrated for its notable antibacterial and anti-inflammatory properties. This study explores a novel delivery method for wormwood, aiming for more convenient and versatile applications. Specifically, we present the first investigation into combining wormwood with microstructures to create a microneedle (MN) patch for wound healing. The wormwood microneedle (WMN) patch is formulated with milled wormwood sap, calcium carbonate, and sodium hyaluronate. The addition of 0.3% (w/v) sodium hyaluronate enhances the mechanical strength of the WMN patch. Pectin, derived from wormwood, is combined with calcium carbonate to create a gelatinous and solidified substance. The WMN patch exhibits a well-defined shape and sufficient mechanical strength to penetrate the epidermis, as confirmed by our results. In vitro experiments demonstrate the biocompatibility of the WMN patch with fibroblasts and highlight its antibacterial and anti-inflammatory properties. Furthermore, the patch facilitates collagen deposition at the wound site. In an excisional rat model, the WMN patch significantly accelerates the wound closure rate compared to the control group. Our findings suggest that the WMN patch has the potential to serve as a natural treatment for wound healing. Additionally, this approach can be extended to other biologically active substances with similar physiochemical characteristics in future applications.

Collagen-Based Dissolving Microneedles with Flexible Pedestals: A Transdermal Delivery System for Both Anti-Aging and Skin Diseases

Biocompatible polymer microneedles (MNs) are emerging as a promising platform for transdermal drug delivery, especially for facial treatments. Therefore, an MN patch in this study uses hydrolyzed collagen (HC) contained in skin cells as the main raw material and adopts a two-step cast method to develop a rapidly dissolving microneedle (DMN) to deliver collagen in a simple and minimally invasive way, allowing the release of the encapsulated drug in the skin. By optimizing the formulation and proportion of HC and auxiliary support materials, the mechanical strength required to pierce the skin is obtained, while the soft pedestal allows for flexibility in application. The DMNs can dissolve completely in the skin within 15 min and release within ≈ 8 h, and do not cause toxicity or irritation when being applied. In contrast to the ineffectiveness of oral and external application, and the high risk of dermal injection, drug-loaded DMNs overcome the drawbacks of traditional methods with direct penetration and minimally invasive manner, enabling efficient and safe treatment. The successful preparation and research of HC DMNs have innovative and practical significance in this field, and it is expected to become a simple, effective, and popular transdermal drug delivery platform for cosmetics.

Fabrication of polyvinyl pyrrolidone-K90/Eudragit RL100-based dissolving microneedle patches loaded with alpha-arbutin and resveratrol for skin depigmentation

Alpha-arbutin (AA) and resveratrol (Res) are widely used in skin-lightening products. However, current topical formulations have minimal skin-lightening effects due to the low absorption and poor solubility of these active compounds. This study investigated the efficacy and safety of using dissolving microneedle (DMN) patches to improve the delivery of AA and Res for skin depigmentation. The DMN patches (F0-F3) fabricated from polyvinyl pyrrolidone-K90 (PVP-K90)/Eudragit RL100 blends successfully penetrated excised porcine skin and showed sufficient mechanical strength to resist compression forces. Loading DMNs with 10% AA and 2% Res at a ratio of 5 : 1 (F3) resulted in a synergistic interaction between the drugs with desirable dissolving ability, drug loading, and stability. Furthermore, both in vitro and in vivo studies revealed that the use of F3 DMN patches successfully enhanced the intradermal delivery of AA and Res over a 24 h period, with the delivered amount being higher (∼2.6 times) than that provided by a cream formulation (P < 0.05). After removing the DMN patches, the mice's skin was spontaneously and completely resealed within 12 h. In clinical studies, F3 DMN patches slightly decreased the melanin index of the participants without causing skin irritation or erythema at any time during the 24 h period when the patches were applied (P < 0.05). Moreover, application of the patches for 24 h was not found to affect skin hydration, transepidermal water loss, or skin elasticity. Therefore, AA/Res-loaded DMN patches could offer a promising approach for the effective local delivery of cosmetic agents for skin depigmentation.

Bioactive Materials Based on Hydroxypropyl Methylcellulose and Silver Nanoparticles: Structural-Morphological Characterization and Antimicrobial Testing

The progress achieved in recent years in the biomedical field justifies the objective evaluation of new techniques and materials obtained by using silver in different forms as metallic silver, silver salts, and nanoparticles. Thus, the antibacterial, antiviral, antifungal, antioxidant, and anti-inflammatory activity of silver nanoparticles (AgNPs) confers to newly obtained materials characteristics that make them ideal candidates in a wide spectrum of applications. In the present study, the use of hydroxypropyl methyl cellulose (HPMC) in the new formulation, by embedding AgNPs with antibacterial activity, using poly(N-vinylpyrrolidone) (PVP) as a stabilizing agent was investigated. AgNPs were incorporated in HPMC solutions, by thermal reduction of silver ions to silver nanoparticles, using PVP as a stabilizer; a technique that ensures the efficiency and selectivity of the obtained materials. The rheological properties, morphology, in vitro antimicrobial activity, and stability/catching of Ag nanoparticles in resulting HPMC/PVP-AgNPs materials were evaluated. The obtained rheological parameters highlight the multifunctional roles of PVP, focusing on the stabilizing effect of new formulations but also the optimization of some properties of the studied materials. The silver amount was quantified using the spectroscopy techniques (energy-dispersive X-ray fluorescence (XRF), energy-dispersive X-ray spectroscopy (EDX)), while formation of the AgNPs was confirmed using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), transmission electron microscopy (TEM), and dynamic light scattering (DLS). Also, the morphological examination (Atomic Force Microscopy (AFM) and Scanning electron microscopy (SEM)) by means of the texture roughness parameters has evidenced favorable characteristics for targeted applications. Antibacterial activity was tested against Escherichia coli and Staphylococcus aureus and was found to be substantially improved was silver was added in the studied systems.

The Skin-Whitening and Antioxidant Effects of Protocatechuic Acid (PCA) Derivatives in Melanoma and Fibroblast Cell Lines

The skin is the most voluminous organ of the human body and is exposed to the outer environment. Such exposed skin suffers from the effects of various intrinsic and extrinsic aging factors. Skin aging is characterized by features such as wrinkling, loss of elasticity, and skin pigmentation. Skin pigmentation occurs in skin aging and is caused by hyper-melanogenesis and oxidative stress. Protocatechuic acid (PCA) is a natural secondary metabolite from a plant-based source widely used as a cosmetic ingredient. We chemically designed and synthesized PCA derivatives conjugated with alkyl esters to develop effective chemicals that have skin-whitening and antioxidant effects and enhance the pharmacological activities of PCA. We identified that melanin biosynthesis in B16 melanoma cells treated with alpha-melanocyte-stimulating hormone (α-MSH) is decreased by PCA derivatives. We also found that PCA derivatives effectively have antioxidant effects in HS68 fibroblast cells. In this study, we suggest that our PCA derivatives are potent ingredients for developing cosmetics with skin-whitening and antioxidant effects.

Transdermal delivery of allopurinol to acute hyperuricemic mice via polymer microneedles for the regulation of serum uric acid levels

Allopurinol (AP) is widely used to treat hyperuricemia which may cause severe side effects upon oral administration. Alternative means for the treatment of hyperuricemia are demanded to simultaneously facilitate drug absorption, patient compliance, and fewer side effects. In this study, a new polymer microneedle (MN) system was developed for the transdermal delivery of AP to acute hyperuricemic mice. This study aims to achieve the controllable regulation of serum uric acid (SUA) levels with fewer side effects compared with oral administration. The matrix of polymer MNs consisted of polyvinylpyrrolidone (PVP) and polycaprolactone (PCL), in which the rapid dissolution of PVP offers a rapid dissolution of AP into the blood and the biodegradability of PCL resulting in a sustainable drug release behavior. An in vivo study demonstrated that the AP-loaded MN system can effectively reduce the SUA levels as oral administration with lower side effects, which will be conducive to reducing the adverse reactions and improving the bioavailability of AP. This MN-mediated strategy can facilitate transcutaneous hyperuricemia treatment and provide a new alternative for the exploration of clinical treatment of hyperuricemia and improvement of patient compliance.

A Systematic Overview of Eudragit® Based Copolymer for Smart Healthcare

Eudragit, synthesized by radical polymerization, is used for enteric coating, precise temporal release, and targeting the entire gastrointestinal system. Evonik Healthcare Germany offers different grades of Eudragit. The ratio of methacrylic acid to its methacrylate-based monomers used in the polymerization reaction defines the final product's characteristics and consequently its potential range of applications. Since 1953, these polymers have been made to use in a wide range of healthcare applications around the world. In this review, we reviewed the "known of knowns and known of unknowns" about Eudragit, from molecule to material design, its characterization, and its applications in healthcare.

PVP-microneedle array for drug delivery: mechanical insight, biodegradation, and recent advances

Microneedle arrays are micron-sized needles usually attached to a supporting base or patch facilitated drug delivery for systemic effects. Polyvinylpyrrolidone (PVP) is a lactam polymer containing an internal amide linkage. Because of its versatility and biocompatibility, it has been widely utilized to treat several skin, bone and eye problems. Due to its specific and unique properties, the researchers realize its utility as a polymer of tremendous potential. PVP-based dissolvable microneedles have widely been utilized as a carrier for delivering DNAs, proteins, vitamins, and several biological macromolecules transdermally. However, it does not get biodegraded into the body. Therefore, the presence of its fragments in the body post-treatment needs proper justification. The adequate justification for the fate of the fragment's end products in the body will allow even better utilization of PVP. This review analyses and illustrates various experimental findings to highlight the most recent advancements and applications of PVP microneedles in drug delivery systems and cosmetology and the potential for PVP microneedles in treating dermal and systemic disorders. This review presents the expected mode of PVP biodegradation in aqueous and soil environments as a waste material, its inertness, biocompatibility, and the importance of PVP as a fabricating material, pharmaceutical uses, and non-toxic profile.

Polymeric Biomaterials for Topical Drug Delivery in the Oral Cavity: Advances on Devices and Manufacturing Technologies

There are several routes of drug administration, and each one has advantages and limitations. In the case of the topical application in the oral cavity, comprising the buccal, sublingual, palatal, and gingival regions, the advantage is that it is painless, non-invasive, allows easy application of the formulation, and it is capable of avoiding the need of drug swallowing by the patient, a matter of relevance for children and the elderly. Another advantage is the high permeability of the oral mucosa, which may deliver very high amounts of medication rapidly to the bloodstream without significant damage to the stomach. This route also allows the local treatment of lesions that affect the oral cavity, as an alternative to systemic approaches involving injection-based methods and oral medications that require drug swallowing. Thus, this drug delivery route has been arousing great interest in the pharmaceutical industry. This review aims to condense information on the types of biomaterials and polymers used for this functionality, as well as on production methods and market perspectives of this topical drug delivery route.

Chitosan-based microneedle arrays for dermal delivery of Centella Asiatica

Centella asiatica, a medicinal herb used for wound healing, has a limited effect when delivered as an ointment. Centella asiatica's active component asiatic acid (AA) increases extracellular matrix development and reduces inflammation but cannot penetrate the stratum corneum to access deeper skin layers. To bypass the stratum corneum, we formulated two types of AA-loaded microneedle arrays. We fabricated, characterised and optimised a dissolving array made from chitosan and PVA and a hydrogel array made from chitosan and PVP. Both needles were strong and long enough to pierce the epidermis without breaking. Both were biocompatible with keratinocytes and fibroblasts (>75% viability at 100% concentration) and showed a sustained drug release over 48 hours. The hydrogel microneedle released more AA (52.2%) than the dissolving formulation (26.4%); thus, we evaluated them in an excisional rat model. The hydrogel microneedle arrays significantly increased the rate of wound closure compared to the control. This research has shown that the chitosan-PVA hydrogel microneedles could penetrate the epidermis, effectively release AA, and increase the wound closure rate. This AA-loaded delivery system shows promise as a natural treatment for wound healing and may be applied to other bioactive compounds with similar physiochemical properties in the future.

Feasibility of Enhancing Skin Permeability of Acyclovir through Sterile Topical Lyophilized Wafer on Self-Dissolving Microneedle-Treated Skin

Acyclovir is an antiviral drug that is frequently prescribed for the herpes virus. However, the drug requires frequent dosing due to limited bioavailability (10–26.7%). The rationale of the present study was to develop a self-dissolving microneedle system for local and systemic delivery of acyclovir using a topical lyophilized wafer on microneedle-treated skin to provide the drug at the site of infection. The microneedles prepared with hydroxypropyl methylcellulose (HPMC) (8% w/w) or HPMC (8% w/w)-polyvinyl pyrrolidone (PVP) (30% w/w) penetrated excised rat skin, showing sufficient mechanical strength and rapid polymer dissolution. The topical wafer was prepared with acyclovir (40% w/w; equivalent to 200 mg of drug), gelatin (10% w/w), mannitol (5% w/w), and sodium chloride (5% w/w). The uniform distribution of acyclovir within the wafer in an amorphous form was confirmed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). No polymer–drug interaction was evident in the lyophilized wafer as per Fourier transform infrared spectroscopy (FTIR) analysis. The wafer showed a sufficiently porous structure for rapid hydration as per scanning electron microscopy (SEM) analysis. During ex-vivo analysis, the skin was pre-treated with a self-dissolving microneedle array for 5 minutes, and the wafer was placed on this microporated-skin. Topical wafer provided ∼7–11 times higher skin concentration than the ID₉₉ reported with a lower lag-time. Based on in-vivo testing, ∼2.58 µg/ml of Cmax was achieved in rabbit plasma during 24 hours’ study. Our findings suggest that the self-dissolving microneedle-assisted topical wafer, proposed for the first time, would be efficacious against the infection residing in the skin layer and for systemic therapy.

Recent advances in polymer microneedles for drug transdermal delivery: Design strategies and applications

In recent years, the transdermal drug delivery based on microneedles (MNs) technology has received extensive attention, which offers a safer and painless alternative to hypodermic needle injection. They can pierce the stratum corneum and deliver drugs to the epidermis and dermis-structures of skin, showing prominent properties such as minimally invasive, bypassing first-pass metabolism, and self-administered. A range of materials have been used to fabricate MNs, such as silicon, metal, glass, and polymers. Among them, polymer MNs have gained increasing attention from pharmaceutical and cosmetic companies as one of the promising drug delivery methods. Microneedle products have recently become available on the market, and some of them are under evaluation for efficacy and safety. This paper focuses on current state of polymer MNs in the drug transdermal delivery. The materials and methods for the fabrication of polymer MNs and their drug administration are described. The recent progresses of polymer MNs for treatment of cancer, vaccine delivery, blood glucose regulation, androgenetic alopecia, obesity, tissue healing, myocardial infarction and gout are reviewed. The challenges of MNs technology are summarized and the future development trend of MNs is also prospected. This article is protected by copyright. All rights reserved.

Design and fabrication of r-hirudin loaded dissolving microneedle patch for minimally invasive and long-term treatment of thromboembolic disease

Cardiovascular disease is the leading cause of global mortality, with anticoagulant therapy being the main prevention and treatment strategy. Recombinant hirudin (r-hirudin) is a direct thrombin inhibitor that can potentially prevent thrombosis via subcutaneous (SC) and intravenous (IV) administration, but there is a risk of haemorrhage via SC and IV. Thus, microneedle (MN) provides painless and sanitary alternatives to syringes and oral administration. However, the current technological process for the micro mould is complicated and expensive. The micro mould obtained via three-dimensional (3D) printing is expected to save time and cost, as well as provide a diverse range of MNs. Therefore, we explored a method for MNs array model production based on 3D printing and translate it to micro mould that can be used for fabrication of dissolving MNs patch. The results show that r-hirudin-loaded and hyaluronic acid (HA)-based MNs can achieve transdermal drug delivery and exhibit significant potential in the prevention of thromboembolic disease without bleeding in animal models. These results indicate that based on 3D printing technology, MNs combined with r-hirudin are expected to achieve diverse customizable MNs and thus realize personalized transdermal anticoagulant delivery for minimally invasive and long-term treatment of thrombotic disease.

Hydrophobically Grafted Pullulan Nanocarriers for Percutaneous Delivery: Preparation and Preliminary In Vitro Characterisation

Polymeric colloidal nanocarriers formulated from hydrophobically grafted carbohydrates have been the subject of intensive research due to their potential to increase the percutaneous penetration of hydrophilic actives. To this goal, a series of hydrophobically grafted pullulan (BMO-PUL) derivatives with varying degree of grafting (5–64%) was prepared through functionalisation with 2-(butoxymethyl)oxirane. The results demonstrated that monodispersed BMO-PUL nanocarriers (size range 125–185 nm) could be easily prepared via nanoprecipitation; they exhibit close-to-spherical morphology and adequate stability at physiologically relevant pH. The critical micellar concentration of BMO-PUL was found to be inversely proportional to their molecular weight (Mw) and degree of grafting (DG), with values of 60 mg/L and 40 mg/L for DG of 12.6% and 33.8%, respectively. The polymeric nanocarriers were loaded with the low Mw hydrophilic active α-arbutin (16% loading), and the release of this active was studied at varying pH values (5 and 7), with a slightly faster release observed in acidic conditions; the release profiles can be best described by a first-order kinetic model. In vitro investigations of BMO-PUL nanocarriers (concentration range 0.1–4 mg/mL) using immortalised skin human keratinocytes cells (HaCaT) evidenced their lack of toxicity, with more than 85% cell viability after 24 h. A four-fold enhance in arbutin permeation through HaCaT monolayers was recorded when the active was encapsulated within the BMO-PUL nanocarriers. Altogether, the results obtained from the in vitro studies highlighted the potential of BMO-PUL nanocarriers for percutaneous delivery applications, which would warrant further investigation in vivo.

Formulation and In-Vitro Characterisation of Cross-Linked Amphiphilic Guar Gum Nanocarriers for Percutaneous Delivery of Arbutin

Nano-colloidal systems formulated from amphiphilically-modified polysaccharides (degree of modification 16.6%) are focus of prominent study due to their potential to augment active penetration across the skin. Here we report the synthesis of amphiphilically-modified guar gum (GBE-GG) prepared by grafting with glycidol butyl ether (GBE), which were subsequently formed into nanocarriers and loaded with α-arbutin (22.3% loading). The monodispersed and close-to-spherical nanocarriers (size range 239-297 nm) formed via cross-linking were adequately stable mainly at low temperature (4 °C) under physiological pH condition. α-arbutin was released from GBE-GG NPs in a more sustained manner and the release profiles can be accurately represented by the 1^st order kinetic model. In-vitro interactions on immortalised human keratinocytes (HaCaT) cells revealed an increase in biological membrane permeability as well as the absence of cellular toxicity at application pertinent concentrations. No substantial haemolytic activity appeared and flow cytometry analysis revealed effective cellular uptake, suggesting their potential as promising nanocarriers for percutaneous delivery that warrants further comprehensive research.

Arbutin as a Skin Depigmenting Agent with Antimelanogenic and Antioxidant Properties

Arbutin is a compound of hydroquinone and D-glucose, and it has been over 30 years since there have been serious studies on the skin lightening action of this substance. In the meantime, there have been debates and validation studies about the mechanism of action of this substance as well as its skin lightening efficacy and safety. Several analogs or derivatives of arbutin have been developed and studied for their melanin synthesis inhibitory action. Formulations have been developed to improve the stability, transdermal delivery, and release of arbutin, and device usage to promote skin absorption has been developed. Substances that inhibit melanin synthesis synergistically with arbutin have been explored. The skin lightening efficacy of arbutin alone or in combination with other active ingredients has been clinically evaluated. Combined therapy with arbutin and laser could give enhanced depigmenting efficacy. The use of arbutin causes dermatitis rarely, and caution is recommended for the use of arbutin-containing products, especially from the viewpoint that hydroquinone may be generated during product use. Studies on the antioxidant properties of arbutin are emerging, and these antioxidant properties are proposed to contribute to the skin depigmenting action of arbutin. It is hoped that this review will help to understand the pros and cons of arbutin as a cosmetic ingredient, and will lead to future research directions for developing advanced skin lightening and protecting cosmetic products.

Design and Evaluation of Dissolving Microneedles for Enhanced Dermal Delivery of Propranolol Hydrochloride

Oral propranolol hydrochloride has been the first-line treatment for infantile hemangioma (IH), whereas systemic exposure to propranolol has the potential of causing serious adverse reactions. Dermal delivery of propranolol is preferable due to high local drug concentration and fewer adverse effects. However, propranolol hydrochloride (BCS class I) is highly hydrophilic and has difficulty in penetrating the stratum corneum (SC) barrier. Dissolving microneedles (MNs) are an efficient tool for overcoming the barrier of the SC and enhancing dermal drug delivery. In this study, propranolol hydrochloride-loaded dissolving MNs were fabricated by using hyaluronic acid and polyvinyl pyrrolidone as matrix materials. Controllable drug loading in needle tips was achieved by a two-step casting procedure. The needles were good in mechanical strength for penetrating the SC while presented excellent dissolving capability for releasing propranolol hydrochloride. In comparison with the solution counterpart, irrespective of being applied to intact skin or solid MNs-pretreated skin, dissolving MNs significantly increased the permeability and skin retention of propranolol. In conclusion, dissolving MNs could be a potential approach for enhancing dermal delivery of propranolol to treat IH.

Engineering Microneedle Patches for Improved Penetration: Analysis, Skin Models and Factors Affecting Needle Insertion

Transdermal microneedle (MN) patches are a promising tool used to transport a wide variety of active compounds into the skin. To serve as a substitute for common hypodermic needles, MNs must pierce the human stratum corneum (~ 10 to 20 µm), without rupturing or bending during penetration. This ensures that the cargo is released at the predetermined place and time. Therefore, the ability of MN patches to sufficiently pierce the skin is a crucial requirement. In the current review, the pain signal and its management during application of MNs and typical hypodermic needles are presented and compared. This is followed by a discussion on mechanical analysis and skin models used for insertion tests before application to clinical practice. Factors that affect insertion (e.g., geometry, material composition and cross-linking of MNs), along with recent advancements in developed strategies (e.g., insertion responsive patches and 3D printed biomimetic MNs using two-photon lithography) to improve the skin penetration are highlighted to provide a backdrop for future research.

Combination and efficiency: preparation of dissolving microneedles array loaded with two active ingredients and its anti-pigmentation effects on guinea pigs

Hyperpigmentation is a common skin disorder caused by excessive melanogenesis and uneven dispersion of melanin in the skin. To combine multiple active agents with an efficient transdermal drug delivery system is an effective strategy to combat UV induced skin pigmentation. In this work, Arbutin (Arb) and Vitamin C (Vc) mixed in 1:1 were found to have the greatest inhibition effects on melanogenesis and tyrosinase activity in B16 murine melanoma cells. And hyaluronic acid (HA) based dissolving microneedles array (DMNA) was employed to overcome the skin barriers for improved topical drug delivery, which exhibited the most desirable features, including morphology, mechanical properties, dissolving ability, and the highest drug loading. Furthermore, DMNA could greatly increase the stability of Vc during storage without adding any antioxidant which is an important issue for Vc administration. Pharmacodynamics study showed that DMNA loaded with Arb and Vc could synergistically suppress UVB-induced hyperpigmentation in guinea pig skin. This work provides a promising treatment strategy and solution for skin pigmentation and other skin problems.

Pharmaceutical assessment of polyvinylpyrrolidone (PVP): As excipient from conventional to controlled delivery systems with a spotlight on COVID-19 inhibition

Polyvinylpyrrolidone (PVP) is a water-soluble polymer obtained by polymerization of monomer N-vinylpyrrolidone. PVP is an inert, non-toxic, temperature-resistant, pH-stable, biocompatible, biodegradable polymer that helps to encapsulate and cater both hydrophilic and lipophilic drugs. These advantages enable PVP a versatile excipient in the formulation development of broad conventional to novel controlled delivery systems. PVP has tunable properties and can be used as a brace component for gene delivery, orthopedic implants, and tissue engineering applications. Based on different molecular weights and modified forms, PVP can lead to exceptional beneficial features with varying chemical properties. Graft copolymerization and other techniques assist PVP to conjugate with poorly soluble drugs that can inflate bioavailability and even introduces the desired swelling tract for their control or sustained release. The present review provides chemistry, mechanical, physicochemical properties, evaluation parameters, dewy preparation methods of PVP derivatives intended for designing conventional to controlled systems for drug, gene, and cosmetic delivery. The past and growing interest in PVP establishes it as a promising polymer to enhance the trait and performance of current generation pharmaceutical dosage forms. Furthermore, the scrutiny explores existing patents, marketed products, new and futuristic approaches of PVP that have been identified and scope for future development, characterization, and its use. The exploration spotlights the importance and role of PVP in the design of Povidone-iodine (PVP-I) and clinical trials to assess therapeutic efficacy against the COVID-19 in the current pandemic scenario.

Applications of Natural, Semi-Synthetic, and Synthetic Polymers in Cosmetic Formulations

Cosmetics composed of synthetic and/or semi-synthetic polymers, associated or not with natural polymers, exhibit a dashing design, with thermal and chemo-sensitive properties. Cosmetic polymers are also used for the preparation of nanoparticles for the delivery of, e.g., fragrances, with the purpose to modify their release profile and also reducing the risk of evaporation. Besides, other cosmetically active nutrients, dermal permeation enhancers, have also been loaded into nanoparticles to improve their bioactivities on the skin. The use of natural polymers in cosmetic formulations is of particular relevance because of their biocompatible, safe, and eco-friendly character. These formulations are highly attractive and marketable to consumers, and are suitable for a plethora of applications, including make-up, skin, and hair care, and as modifiers and stabilizers. In this review, natural synthetic, semi-synthetic, and synthetic polymers are discussed considering their properties for cosmetic applications. Their uses in conventional and novel formulations are also presented.

Rapid biodegradable microneedles with allergen reservoir for skin allergy test

With the increasing allergy cases worldwide, this study introduces a biodegradable microneedle system to facilitate allergy testing process. Dissolving microneedle provides a minimally invasive manner to go through skin barrier while avoiding needle phobia among patents, especially children. The microneedles were fabricated using copolymer polyvinylpyrrolidone-co-methacrylic acid (PVP-MAA) material. To ensure the successful insertion of microneedles into the skin, we tailored the mechanical strength of the copolymer by adjusting the weight ratio of two constituted polymers. A reservoir was designed to load allergy specimen for the allergy test. This system is expected to offer a simple and effective allergy testing that can facilitate the allergy testing protocol.

Fabrication, characterization and comparison of α-arbutin loaded dissolving and hydrogel forming microneedles

In this study, polyacrylic acid-co-maleic acid (PAMA) and polyvinyl alcohol (PVA) (1:4) were used to fabricate dissolving microneedles (DMNs) and hydrogel forming microneedles (HMNs) which incorporated α-arbutin. Αlpha-arbutin is commonly used as a skin lightening agent. However, it has poor penetration ability due to its hydrophilic properties. The purpose of this study was to compare the permeation of α-arbutin into the skin using DMNs and HMNs. Both types of microneedles (MNs) were sharp, strong with elegant appearance and approximately 100% penetrated the neonatal porcine skin. All needles of α-arbutin loaded DMNs were completely dissolved within 45 min, whereas maximum swelling of HMNs was observed at 4 h. In vitro permeation studies showed that α-arbutin loaded DMNs and HMNs provided significantly about 4.5 and 2.8 times, respectively, greater α-arbutin permeability than gel and commercial cream (P < 0.05). In vivo study also showed high intradermal delivery of α-arbutin levels using DMNs (5.33 µg/mL) and HMNs (1.47 µg/mL) when compared to that of commercial cream 0.15 µg/mL. Moreover, the micro-holes caused by applying MNs can reseal within 1 h. MNs were also stable at 25 °C for 3 months. The results suggested that DMNs and HMNs developed have a promising platform for transdermal delivery.