Failure of the Ring polyethylene uncemented acetabular cup

Pseudotumor and Subsequent Implant Loosening as a Complication of Revision Total Hip Arthroplasty with Ceramic-on-Metal Bearing: A Case Report

Pseudotumors are not uncommon complications after total hip arthroplasty (THA) and may occur due to differences in bearing surfaces of the head and the liner ranging from soft to hard articulation. The most common causes of pseudotumors are foreign-body reaction, hypersensitivity and wear debris. The spectrum of pseudotumor presentation following THA varies greatly-from completely asymptomatic to clear implant failure. We report a case of pseudo-tumor formation with acetabular cup aseptic loosening after revision ceramic-on-metal hip arthroplasty. The patient described herein underwent pseudotumor excision and re-revision complex arthroplasty using a trabecular metal shell and buttress with ceramic-on-polyethylene THA. Surgeons should be aware of the possibility of a pseudotumor when dealing with revisions to help prevent rapid progression of cup loosening and implant failure, and should intervene early to avoid complex arthroplasty procedures.

A rare case of pseudotumor formation associated with methyl methacrylate hypersensitivity in a patient following cemented total knee arthroplasty

Hypersensitivity to orthopedic implant materials has been well documented with potential catastrophic consequences if not addressed pre-operatively. The spectrum of reactions is wide, from mild non-specific pain with localized erythema to severe periprosthetic inflammatory destruction and pseudotumor formation. It is therefore essential to identify patients who have or are at risk for implant-associated hypersensitivity. Although metal sensitivity is commonly cited as the cause of these reactions, methyl methacrylate (MMA) has rarely been implicated. To the best of our knowledge, methyl methacrylate-associated pseudotumor formation has not yet been described. The following is a case report of a 68-year-old female who, after undergoing a routine cemented right total knee arthroplasty, developed a painless, enlarging mass during a 13-year period. This mass was found to be a pseudotumor in association with methyl methacrylate hypersensitivity. A review of pseudotumor pathogenesis, methyl methacrylate hypersensitivity, and preoperative preventative care is discussed.

Bone remodeling around the tibial component of distal femoral expandable endoprosthesis

Radiographs of 33 patients who had an expandable prosthesis inserted after tumor resection in the distal femur were evaluated. We hypothesized that, when a sleeve was present, there was greater stem migration and cortical reaction. The thickness of medial and lateral cortices of the tibia was measured at 6 months and on the last follow-up radiograph. The distance from the edge of the prosthesis to the cortical edge was also compared. When a sleeve was present, there was greater stem migration (P < .001) and a greater increase in lateral cortical thickness (P < .001). There was a higher revision rate when a sleeve was used, but this was not statistically significant. There was no difference in function according to the Toronto Extremity Salvage Score (TESS) between the 2 groups. This is the first study to demonstrate that the presence of a polyethylene sleeve is associated with a tendency for the tibial prosthesis to migrate laterally and cause a greater sclerotic reaction.

Primary total hip arthroplasty using a grit-blasted, press-fit femoral prosthesis.Long-term results with survivorship analysis

BACKGROUND

This report presents the initial experience with the use of a grit-blasted, press-fit femoral prosthesis.

METHODS

The first 300 consecutive primary total hip arthroplasty procedures using a collarless, three-dimensional tapered, straight, titanium alloy stem with a grit-blasted surface (performed in 299 patients) were evaluated with independent clinical and radiographic follow-up examinations up to sixteen years. Eight different types of acetabular components, including a cementless all-polyethylene socket in 80 percent of the cases, were used. Radiographic evaluation, performed by an independent observer using a zonal analysis method, included assessment of component migration, Enghs implant-bone femoral fixation score, implant-bone demarcations, and periprosthetic osteolysis. The average duration of long-term radiographic follow-up was 12.6 years (range; 10 to 16 years).

RESULTS

At last examination only five hips were lost to follow-up and 69 patients were deceased. The overall mechanical failure rate (i.e. unstable with or without revision) of the femoral component was 2 percent. The femoral revision rate was 7 percent (two hips for aseptic loosening, five hips for septic loosening, and twelve hips with osseointegrated stems for severe progressive femoral osteolysis) and the acetabular revision rate was 27 percent (revised for either socket migration or progressive peri-acetabular osteolysis or both). Survivorship, based on any revision (femoral or acetabular) was 89 percent at ten years and 62 percent at fourteen years; survivorship of the femoral component was 95 percent at ten years and 90 percent at fourteen years. The incidence of femoral periprosthetic osteolysis, by radiographic examination at ten years or more was 47 percent, including 12 hips (5 percent) with distal endosteal osteolysis. Femoral implant-bone fixation was stable, bone-ongrowth in 97 percent; stable, fibrous-fixation in 1 percent, and unstable, fibrous-fixation in 2 percent of the cases.

CONCLUSIONS

The grit-blasted, press-fit, collarless, tapered femoral component continued to per-form well clinically and radiographically up to sixteen years of follow-up despite the challenging environment of periprosthetic osteolysis associated with the acetabular component design. The high incidence of failure among the cementless all-polyethylene sockets was not unexpected and the use of this acetabular implant was discontinued in 1985. While considered a "first-generation" cementless stem, this implant is still in use virtually without design modifications. This study demonstrates the durability of the results of the grit-blasted femoral component and indicates that such an implant offers a viable alternative for fixation without bone cement. (Hip International 2002; 2: 55-72).

Metal on metal bearings in hip arthroplasty

Periprosthetic osteolysis caused by wear debris released from the bearing surface of polyethylene components is the major problem in contemporary hip arthroplasty. Several types of metal on metal prostheses were developed in the 1960s, but by the mid 1970s they were completely displaced by polyethylene bearings. There have been several generations of all metal components with significant variation in design, tolerances, and bearing surface quality. A number of these hips have survived for more than 25 years because of low wear rates and minimal osteolysis. Identification of the characteristics that contributed to long term function is important. The historical development and clinical results of metal on metal hip arthroplasties are presented. Factors that led to the abandonment of the metal on metal bearings are related to: (1) the early success of the Charnley prosthesis; (2) the frictional torque issue; (3) carcinogenesis concerns; (4) metal sensitivity concerns; (5) high infection rates; and (6) increased strain rates in periprosthetic bone and fatigue fractures of the acetabular floor. The accumulated experience to date enables one to evaluate all the factors with a different perspective and makes the use of newer metal on metal bearings a viable option in younger patients.