2.05-µm all-fiber laser source designed for CO2 and wind coherent lidar measurement

2.7 μm backward wave optical parametric oscillator source for CO2 spectroscopy

In this work, a novel 2.7 µm source used for CO2 and H2O vapor spectroscopy using the backward propagating wave of a backward wave optical parametric oscillator (BWOPO) is demonstrated for the first time to our knowledge. The unique properties of BWOPOs eliminate the need for additional spectral narrowing or wavelength stabilization, enabling the use of a multi-longitudinal mode Q-switched pump laser centered around 1030 nm. A full characterization of the source is presented, revealing a central output at 2712 nm, showcasing a temperature tuning of -1.77 GHz/K, and achieving an output pulse energy of 2.3 µJ. Novel methods are introduced for measuring the linewidth and wavelength stability using the ambient laboratory air. These approaches demonstrate a narrow output of 43 pm and establish an upper limit of stability at 65 MHz, with no active means of stabilization. These findings underscore the potential of BWOPOs as a robust platform for future differential absorption lidar (DIAL) systems.

Three-dimensional detection of CO2 and wind using a 1.57 µm coherent differential absorption lidar

A 1.57-µm coherent differential absorption lidar is demonstrated for measuring three-dimensional CO2 and wind fields simultaneously. The maximum detection range of CO2 is up to 6 km with a range resolution of 120 m and a time resolution of 1 min. A preliminary assessment of instrument performance is made with a 1-week continuous observation. The CO2 concentration over a column from 1920 to 2040 m is compared with the one measured by an optical cavity ring-down spectrometer placed on a 2 km-away meteorological tower. The concentration is strongly correlated with the in-situ spectrometer with a correlation coefficient and RMSE of 0.91 and 5.24 ppm. The measurement accuracy of CO2 is specified with a mean and standard deviation of 2.05 ppm and 7.18 ppm, respectively. The regional CO2 concentration and the three-dimensional wind fields are obtained through different scanning modes. Further analysis is conducted on vertical mixing and horizontal transport of CO2 by combining with the measured wind fields.

SBS mitigation by sinusoidal phase modulation of a 1572 nm all-fiber amplifier for lidar CO2 sensing

Lidar C O 2 sensing can be performed by 1572 nm pulsed laser sources. This work presents the development of a fiber amplifier at this wavelength emitting 1 µs FWHM Gaussian pulses at a repetition rate of 7.5 kHz. We obtain the mitigation of stimulated Brillouin scattering (SBS) by shaping the seed laser spectrum into a frequency comb with sinusoidal phase modulation. This frequency comb is compatible with a coherent dual-comb spectroscopy (DCS) method for a targeted lidar C O 2 sensing application. The effect of the harmonics spacing and relative intensity on the SBS threshold is studied. Laser pulses are amplified up to 182 µJ (182 W peak power) from a single-mode erbium (Er) and ytterbium (Yb) co-doped fiber. Those results hold promise for seeding large mode area Er-Yb co-doped fiber power amplifiers.

Hybrid fiber/bulk laser source designed for CO2 and wind measurements at 2.05 µm

We present a hybrid fiber/bulk laser source designed for CO2 and wind monitoring using differential absorption LIDAR (DIAL) and coherent detection at 2.05 µm. This source features a master oscillator power amplifier (MOPA) architecture made of four fiber stages and one single-pass, end-pumped, bulk amplifier. This Letter focuses on the single-pass bulk amplifier performance and on the hybrid architecture benefits for DIAL and coherent detection. The bulk material is a holmium-doped YLF crystal that provides high efficiency amplification at 2.05 µm. This laser offers an energy breakthrough as compared to the classical stimulated Brillouin scattering (SBS) limit encountered in a fiber laser without compromising robustness, thanks to very few free-space optical elements and a small optical path. It delivers pulse energy and repetition frequency of 9.0 or 1.2 mJ/20 kHz with 200 ns quasi Fourier-transform limited pulses.

2 µm band four-wavelength-switchable narrow linewidth fiber laser enabled by fs-laser direct-written polarization-dependent parallel fiber Bragg gratings

We propose and experimentally demonstrate a four-wavelength-switchable single-longitudinal-mode (SLM) narrow linewidth thulium-holmium co-doped fiber laser (THDFL) using two polarization-dependent parallel fiber Bragg gratings (PD-PFBGs). The PD-PFBGs, fabricated using femtosecond (fs) laser direct-writing technology in a standard single-mode fiber (SMF) via a point-by-point method, are used as a four-channel reflection filter. Two FBGs are inscribed in parallel in the fiber core along the axial direction and are uniquely positioned symmetrically on either side of the centerline. This configuration enables polarization-dependent multi-channel filtering capability, which further allows for polarization-control-based four-wavelength-switchable operations of the THDFL. SLM lasing is accomplished by utilizing a simple dual-ring sub-cavity filter. An exceptional output performance of the THDFL is achieved, including an optical signal-to-noise ratio (SNR) of >72 dB, maximum power and wavelength fluctuations of 0.350 dB and 0.024 nm, respectively, and a linewidth of <2 kHz, for all four single-wavelength operations lasing at ∼2000 nm. These performance indicators suggest that the THDFL can be applied in free-space optical communication, atmospheric monitoring, and Lidar.

Laser applications to chemical, security, and environmental analysis: introduction to the feature issue

This Applied Optics feature issue on laser applications to chemical, security, and environmental analysis (LACSEA) highlights papers presented at the LACSEA 2020 Seventeenth Topical Meeting sponsored by The Optical Society (OSA).