Optical gain characterization of Perylene Red-doped PMMA for different pump configurations

Amplified spontaneous emission from a liquid crystalline phase: anisotropic property and active modulation

Amplified spontaneous emission (ASE) is considered to be a primary indication of optical gain in active media without an external resonator. Molecular materials with ASE are expected to be one of the suitable light sources for specific applications such as optical coherent tomography owing to their low coherence and flexible tunability. Concentration quenching of emissive excited states has been a critical issue to boost the quantum efficiency of molecular materials in their condensed phases. The rod-like design of molecules with excited state intramolecular proton transfer (ESIPT) has been demonstrated to overcome this issue in highly-concentrated molecularly-doped systems, as represented by C4alkyne-HBT (2-(4-(1-hexynyl)-2-hydroxyphenyl)-benzothiazole). We designed an ESIPT molecule-doped liquid crystalline (LC) system for optical amplification via the ASE regime with its wide tunability of emission intensity. Detailed ASE behaviour and optical gain of a LC blend of C4alkyne-HBT and 4-pentyl-4'-cyano biphenyl (5CB) was evaluated to afford a maximum optical gain of 16.5 cm-1 with an estimated ASE threshold of optical pumping at 0.6-0.7 mJ cm-2. Although most ASE studies focus on homogeneous solutions, solids, or crystalline states, ASE from a soft-flexible LC phase is quite limited and advantageous for the design of an external optical resonator/cavity structure. Optical excitation parallel and perpendicular to the director resulted in the strong modulation of the ASE. By using the benefits of a LC phase, the ASE was actively modulated under the external electric field by the reorientation of the molecular dipole moment.

Development of an Active Optical Lens for Arc Flashing Detection

This paper contains the design of active optical lenses used for the detection of arc flashing emissions. The phenomenon of an arc flashing emission and its characteristics were contemplated. Methods of preventing these emissions in electric power systems were discussed as well. The article also includes a comparison of commercially available detectors. An analysis of the material properties of fluorescent optical fiber UV-VIS-detecting sensors constitutes a major part of the paper. The main purpose of the work was to make an active lens using photoluminescent materials, which can convert ultraviolet radiation into visible light. As part of the work, active lenses with materials such as Poly(methyl 2-methylpropenoate) (PMMA) and phosphate glass doped with lanthanides, such as terbium (Tb³⁺) and europium (Eu³⁺) ions, were analyzed. These lenses were used to make optical sensors, which were supported by commercially available sensors in their construction.

Gain investigation of Perylene-Red-doped PMMA for stimulated luminescent solar concentrators

Luminescent solar concentrators (LSCs) utilizing stimulated emission by a seed laser are a promising approach to overcome the limitations of conventional LSCs, with a significant reduction of the photovoltaic material. In our previous work, we demonstrated the principle of a stimulated LSC (s-LSC) and correspondingly developed a model for quantifying the output power of such a system, taking into account different important physical parameters. The model suggested Perylene Red (PR) dye as a potential candidate for s-LSCs. Here, we experimentally investigate the gain of PR-doped polymethyl methacrylate (PMMA) required for s-LSCs using a single pump wavelength (instead of the solar spectrum) as a proof of principle. The results found from the experiment are well matched with the previously developed numerical model except for gain saturation, which occurs at a comparatively small seed laser signal power. To investigate the gain saturation, two approaches were taken: investigating (i) spectral hole burning and (ii) triplet state absorption. Experimental investigation of spectral hole burning with PR dyes showed a small effect on the gain saturation. We developed a general state model considering triplet state absorption of the PR dyes for the second approach. The state model suggests that the PR dyes suffer from significant triplet state absorption loss, which obstructs the normal operation of the PR-based s-LSC system.

Modeling of stimulated emission based luminescent solar concentrators

The efficiency improvement of luminescent solar concentrators (LSCs) necessary for practical realization is currently hindered by one major loss mechanism: reabsorption of emitted photons by the luminophores. Recently, we explored a promising technique for reducing reabsorption and also improving directional emission in LSCs utilizing stimulated emission, rather than only spontaneous emission, with an inexpensive seed laser. In this work, a model is developed to quantify the gain (i.e. the amount of amplification of a low power seed laser propagating through the solar-pumped concentrator) of stimulated-LSCs (s-LSCs) considering the effects of different important physical parameters. The net optical output power, available for a small PV cell, from the concentrator can also be determined from the model, which indicates the performance of s-LSCs. Finally, the performance of different existing material systems is investigated using literature values of the parameters required for the model, and a set of optimal parameters is suggested for practical realization of such a device.