Spectroscopy and laser performance of Nd:Lu2O3 crystal

3.73 W all-solid-state dual-wavelength Nd:Lu2O3 crystal laser

The laser output characteristics of N d:L u 2 O 3 crystals were investigated in detail to obtain a dual-wavelength all-solid-state laser. Using 806 nm LD end-face pumped N d:L u 2 O 3 crystals with lengths of 6 mm, a 1076 & 1080 nm laser outputs with a maximum output power of 3.73 W were obtained, with a slope efficiency of 30.4%, an optical-to-optical conversion efficiency of 28.5%, and a power stability of 0.41% for 4 h of continuous measurement. Furthermore, by suppressing the higher-order modes, a high beam quality laser output with beam quality factors of 2.092 and 1.589 in the x and y directions, respectively, and a maximum output power of 1.27 W were obtained. In addition, it was experimentally verified that both wavelengths of the output laser were elliptically polarized.

Mechanism of Surface Defects in Ultra-Precision Machining of Sesquioxide Laser Crystal Tm: GdScO3

It is well-known that the surface quality of laser gain crystal elements is very high in order to ensure the stability of laser system and laser output quality. In the ultra-precision machining process of a new sesquioxide laser crystal Tm: GdScO3, it is required to achieve very high surface shape and very low surface defects. In this paper, the molecular dynamics simulation model of single particle grinding was established. It was found that the normal load and tangential friction imposed by abrasive particles on the surface of components cause the spalling of atoms on the substrate surface, which constitutes the removal of materials at the macro-level. At the same time, it causes the displacement of the sub surface atoms, which constitutes the microscopic defects in the structure. Through the structural characterization of macro defects, it was confirmed that the essence of micro defects is the amorphous and distortion of surface structure, and the depth can reach 100 nm. The results of lapping and polishing experiments show that the adjustment of pressure has a limited effect on the improvement of surface defects in the process of machining crystal elements with granular abrasive.

Infrared Photoluminescence of Nd-Doped Sesquioxide and Fluoride Nanocrystals: A Comparative Study

Lanthanide ions possess various emission channels in the near-infrared region that are well known in bulk crystals but are far less studied in samples with nanometric size. In this work, we present the infrared spectroscopic characterization of various Nd-doped fluoride and sesquioxide nanocrystals, namely Nd:Y2O3, Nd:Lu2O3, Nd:Sc2O3, Nd:YF3, and Nd:LuF3. Emissions from the three main emission bands in the near-infrared region have been observed and the emission cross-sections have been calculated. Moreover, another decay channel at around 2 μm has been observed and ascribed to the 4F3/2→4I15/2 transition. The lifetime of the 4F3/2 level has been measured under LED pumping. Emission cross-sections for the various compounds are calculated in the 1 μm, 900 nm, and 1.3 μm regions and are of the order of 10−20 cm2 in agreement with the literature results. Those in the 2 μm region are of the order of 10−21 cm2.

Efficient laser operation based on transparent Nd:Lu2O3 ceramic fabricated by Spark Plasma Sintering

Efficient laser operation of Nd:Lu₂O₃ ceramic fabricated by Spark Plasma Sintering (SPS) was demonstrated. Transparent Nd:Lu₂O₃ ceramic was successfully fabricated by Spark Plasma Sintering and its laser experiment was done. On the ⁴F_3/2 to ⁴I_11/2 transition, the obtained maximum output is 1.25W at the absorbed pump power of 4.15W with a slope efficiency of 38% and two spectral lines at 1076.7nm and 1080.8nm oscillated simultaneously. The slope efficiency of 38% is near two times higher than the previously demonstrated SPSed Nd:Lu₂O₃ ceramic lasers. On the ⁴F_3/2 to ⁴I_13/2 transition, the laser operated at the wavelength of 1359.7nm and the maximum output of 200mW was obtained at the absorbed pump power of 2.7W.