Femtosecond fiber-feedback optical parametric oscillator

Mode-locked femtosecond laser with a rotary Nd:glass disk

We demonstrate here femtosecond pulses output from a rotary Nd:glass disk laser, mode-locked with semiconductor saturable absorber mirrors. We obtained an average output power of 0.66 W in cw operation and an average output power of 0.49 W with a duration of 324 fs in mode-locked operation in the case of an absorbed pump power of 7.3 W. To the best of our knowledge, it is the first time that sub-picosecond pulses have been obtained from rotary Nd:glass disk lasers. It shows a new concept for all-solid-state mode-locked glass lasers with high power.

Coherently broadened, high-repetition-rate laser for stimulated Raman scattering-spectroscopic optical coherence tomography

We present a novel light source specifically tailored for stimulated Raman scattering-spectroscopic optical coherence tomography (SRS-SOCT), which is, to the best of our knowledge, a novel molecular imaging method that combines the molecular sensitivity of SRS with the spatial and spectral multiplexing capabilities of SOCT. The novel laser consists of an 8 W, 450 fs Yb:KGW oscillator, with a repetition rate of 40 MHz, which delivers the Stokes beam for SRS-SOCT and also pumps and amplifies an optical parametric oscillator (OPO). The output of the amplified OPO is then frequency doubled and coherently broadened using a custom-made tapered fiber that generates bandwidth pulses >40  nm, compressible to <50  fs, with the average power over 150 mW, near the shot-noise limit above 250 kHz. The broadened and compressed pulse simultaneously serves as the pump beam and SOCT light source for SRS-SOCT. This light source is assessed for SRS-SOCT, and its implications for other imaging methods are discussed.

Ultra-stable high average power femtosecond laser system tunable from 1.33 to 20 μm

A highly stable 350 fs laser system with a gap-free tunability from 1.33 to 2.0 μm and 2.13 to 20 μm is demonstrated. Nanojoule-level pulse energy is achieved in the mid-infrared at a 43 MHz repetition rate. The system utilizes a post-amplified fiber-feedback optical parametric oscillator followed by difference frequency generation between the signal and idler. No locking or synchronization electronics are required to achieve outstanding free-running output power and spectral stability of the whole system. Ultra-low intensity noise, close to the pump laser's noise figure, enables shot-noise limited measurements.

Fiber-feedback optical parametric oscillator for half-harmonic generation of sub-100-fs frequency combs around 2 μm

We demonstrate a femtosecond fiber-feedback optical parametric oscillator (OPO) at degeneracy. The OPO cavity comprises an 80-cm-long fiber composed of a combination of normal and anomalous dispersion sections that provide a net intracavity group delay dispersion close to zero. By using a mode-locked, Yb-doped fiber laser as the pump, we achieved half-harmonic generation of 250-MHz, 1.2-nJ nearly transform-limited 97-fs pulses centered at 2090 nm with a total conversion efficiency of 36%.

Multi-Watt femtosecond optical parametric master oscillator power amplifier at 43 MHz

We present a high repetition rate mid-infrared optical parametric master oscillator power amplifier (MOPA) scheme, which is tunable from 1370 to 4120nm. Up to 4.3W average output power are generated at 1370nm, corresponding to a photon conversion efficiency of 78%. Bandwidths of 6 to 12nm with pulse durations between 250 and 400fs have been measured. Strong conversion saturation over the whole signal range is observed, resulting in excellent power stability. The system consists of a fiber-feedback optical parametric oscillator that seeds an optical parametric power amplifier. Both systems are pumped by the same Yb:KGW femtosecond oscillator.

Four-wave-mixing-based optical parametric oscillator delivering energetic, tunable, chirped femtosecond pulses for non-linear biomedical applications

A novel concept for an optical parametric oscillator based on four-wave mixing (FOPO) in an optical fiber is presented. This setup has the ability of generating highly chirped signal and idler pulses with compressed pulse durations below 600 fs and pulse energies of up to 250 nJ. At a fixed pump wavelength of 1040 nm, the emerging signal and idler wavelengths can be easily tuned between 867 to 918 nm and 1200 to 1300 nm, respectively, only by altering the cavity length. With compressed peak powers >100 kW and a repetition rate of only 785 kHz, this source provides tunable intense ultra-short pulses at moderate average powers. This setup constitutes a stable, simple and in many ways superior alternative to bulk state-of-the-art OPO light converters for demanding biomedical applications and non-linear microspectroscopy.

High-power mid-infrared high repetition-rate supercontinuum source based on a chalcogenide step-index fiber

We demonstrate a tunable and robust femtosecond supercontinuum source with a maximum output power of 550 mW and a maximum spectral width of up to 2.0 μm, which can cover the mid-infrared region from 2.3 μm up to 4.9 μm by tuning the pump wavelength. As2S3 chalcogenide step-index fibers with core diameters of 7 and 9 μm are pumped at different wavelengths from 2.5 μm up to 4.1 μm with femtosecond pulses by means of a post-amplified optical parametric oscillator pumped by an Yb:KGW laser. The spectral behavior of the supercontinuum is investigated by changing the pump wavelength, core diameter, fiber length, and pump power. Self-phase modulation is identified as the main broadening mechanism in the normal dispersion regime. This source promises to be an excellent laboratory tool for infrared spectroscopy owing to its high brilliance as demonstrated for the CS2-absorption bands around 3.5 μm.

Mid-infrared Fourier-transform spectroscopy with a high-brilliance tunable laser source: investigating sample areas down to 5 μm diameter

We demonstrate highly sensitive infrared spectroscopy of sample volumes close to the diffraction limit by coupling a femtosecond fiber-feedback optical parametric oscillator (OPO) to a conventional Fourier-transform infrared (FTIR) spectrometer. The high brilliance and long-term stable infrared radiation with 1e(2)-bandwidths up to 125 nm is easily tunable between 1.4 μm and 4.2 μm at 43 MHz repetition rate and thus enables rapid and low-noise infrared spectroscopy. We demonstrate this by measuring typical molecular vibrations in the range of 3 μm. Combined with surface-enhanced infrared spectroscopy, where the confined electromagnetic near-fields of resonantly excited metal nanoparticles are employed to enhance molecular vibrations, we realize the spectroscopic detection of a molecular monolayer of octadecanethiol. In comparison to conventional light sources and synchrotron radiation, our compact table-top OPO system features a significantly improved performance making it highly suitable for rapid analysis of minute amounts of molecular species in life science and medicine laboratories.

Watt-level optical parametric amplifier at 42 MHz tunable from 1.35 to 4.5 μm coherently seeded with solitons

We report on an optical parametric amplifier at high repetition rate of 41.7 MHz seeded by an optical soliton from a tapered fiber. Gap-free signal tuning from 1.35 μm to 1.95 μm with corresponding idler wavelengths from 2.2 μm to 4.5 μm is demonstrated. The system provides up to 1.8 W average power at 1.4 μm, more than 1.1 W up to 1.7 μm, and more than 400 mW up to 4.0 μm with a signal pulse duration of 200 to 300 fs. It is directly pumped by a solid-state oscillator providing up to 7.4 W at 1.04 μm wavelength with 425 fs pulse duration. Soliton-seeding is shown to lead to excellent pulse-to-pulse stability, but it introduces a timing-jitter on the millisecond timescale. Using a two-stage concept the timing-jitter is efficiently suppressed due to the passive synchronization of both conversion stages.

Application of a high power Yb fiber-based laser compatible with commercial optical parametric oscillator for coherent anti-Stokes Raman scattering microscopy

Coherent anti-Stokes Raman scattering (CARS) microscopy is a powerful tool for chemical analysis at a subcellular level, frequently used for imaging lipid dynamics in living cells. We report a high-power picosecond fiber-based laser and its application for optical parametric oscillator (OPO) pumping and CARS microscopy. This fiber-based laser has been carefully characterized. It produces 5 ps pulses with 0.8 nm spectral width at a 1,030 nm wavelength with more than 10 W of average power at 80 MHz repetition rate; these spectral and temporal properties can be slightly modified. We then study the influence of these modifications on the spectral and temporal properties of the OPO. We find that the OPO system generates a weakly spectrally chirped signal beam constituted of 3 ps pulses with 0.4 nm spectral width tunable from 790 to 930 nm optimal for CARS imaging. The frequency doubling unconverted part is composed of 7-8 ps pulses with 0.75 nm spectral width compatible with CARS imaging. We also study the influence of the fiber laser properties on the CARS signal generated by distilled water. In agreement with theory, we find that shorter temporal pulses allow higher peak powers and thus higher CARS signal, if the spectral widths are less than 10 cm(-1) . We demonstrate that this source is suitable for performing CARS imaging of living cells during several hours without photodamages. We finally demonstrate CARS imaging on more complex aquatic organisms called copepods (micro-crustaceans), on which we distinguish morphological details and lipid reserves.

Broadly tunable femtosecond near- and mid-IR source by direct pumping of an OPA with a 41.7 MHz Yb:KGW oscillator

We generate over half a watt of tunable near-IR (1380-1830 nm) and several hundred milliwatts in the mid-IR (2.4-4.2 µm) as well as milliwatt level mid-IR (4.85-9.33 µm) femtosecond radiation by pumping an optical parametric amplifier directly with a 7.4 W Yb:KGW oscillator at 41.7 MHz repetition rate. We use 5 mm PPLN and 2 mm GaSe as downconversion crystals and seed this process by a supercontinuum from a tapered fiber. The system is extremely simple and very stable and could replace more complex OPOs as tunable light sources.

Milliwatt-level mid-infrared (10.5-16.5 μm) difference frequency generation with a femtosecond dual-signal-wavelength optical parametric oscillator

We demonstrate the generation of mid-infrared radiation using a femtosecond dual-signal-wavelength optical parametric oscillator and difference frequency generation in an extracavity gallium selenide or silver gallium diselenide crystal. This system generates up to 4.3 mW of average mid-infrared power. Its spectra can be tuned to between 10.5 μm and 16.5 μm wavelength (952  cm(-1)-606  cm(-1)) with more than 50  cm(-1) spectral bandwidth. We demonstrate that the power and spectra of this system are temporally very stable.

High-power, fiber-laser-pumped, picosecond optical parametric oscillator based on MgO:sPPLT

We report a stable, high-power, mid-infrared synchronously-pumped optical parametric oscillator (SPOPO) based on MgO:sPPLT, pumped by a 1064 nm, picosecond Yb-fiber laser operating at a repetition rate of 81.1 MHz. The singly resonant SPOPO is tunable over 1531-1642 nm (111 nm) in the near-infrared signal and 3022-3488 nm (466 nm) in the mid-infrared idler, providing a total tuning range of 577 nm. Careful optimization of output coupling results in a signal output power as high as 4.3 W at 1593 nm and a mid-infrared idler power of 2 W at 3204 nm for 13.4 W of pump power at a total extraction efficiency of 47%. The SPOPO can be operated near room temperature, down to 30 °C, and exhibits passive peak-to-peak power stability better than 8.6% at 1568 nm (signal) and 8.2% at 3310 nm (idler) over 13 hours at full power. The output signal pulses have duration of 17.5 ps, with a FWHM spectral bandwidth of 1.4 nm centered at 1568 nm.

Compact, high-pulse-energy, picosecond optical parametric oscillator

We report a high-energy optical parametric oscillator (OPO) synchronously pumped by a 7.19 MHz, Yb:fiber-amplified, picosecond, gain-switched laser diode. The 42-m-long ring cavity maintains a compact design through the use of an intracavity optical fiber. The periodically poled MgO-doped LiNbO(3) OPO provides output pulse energies as high as 0.49 μJ at 1.5 μm (signal) and 0.19 μJ at 3.6 μm (idler). Tunability from 1.5 to 1.7 μm and from 2.9 to 3.6 μm is demonstrated, and typical M(2) values of 1.5 × 1.3 and 2.8 × 1.9 are measured for the signal and idler, respectively, at high power.

Pulse energy scaling to 5 microJ from a femtosecond thin disk laser

We report an increase in pulse energy to 5.1 microJ obtained directly from a femtosecond diode-pumped Yb:YAG thin disk laser without external amplification. Stable passive mode locking was obtained with a semiconductor saturable absorber mirror (SESAM). The laser delivers 63 W of average output power in a nearly diffraction-limited beam (M2=1.1) at a center wavelength of 1030 nm. The pulse repetition rate is 12.3 MHz, and the pulses have a duration of 800 fs, which results in a peak power of 5.6 MW. The laser was operated in a box flooded with helium because the nonlinearity of air was found to be a limiting factor for the stability of the pulse formation at increasing pulse energies.

Powerful red-green-blue laser source pumped with a mode-locked thin disk laser

We present a red-green-blue laser source with average powers of 8 W in the red, 23 W in the green, and 10.1 W in the blue. The entire pump power for the nonlinear conversion stages is provided by a single laser oscillator without any amplifier stages. Our system does not require any synchronized cavities, and all nonlinear crystals except one are critically phase matched at room temperature.

High-power femtosecond fiber-feedback optical parametric oscillator based on periodically poled stoichiometric LiTaO3

We demonstrate a synchronously pumped high-gain optical parametric oscillator with feedback through a fiber, using a passively mode-locked Yb:YAG thin-disk laser as a pump source. We obtain as much as 19-W average signal power at a wavelength of 1.45 microm in 840-fs pulses and 7.8 W of idler power at 3.57 microm. The repetition rate of the pulses is 56 MHz, and the transverse beam quality of the generated signal is M2 < 1.6.

Recent developments in compact ultrafast lasers

Ultrafast lasers, which generate optical pulses in the picosecond and femtosecond range, have progressed over the past decade from complicated and specialized laboratory systems to compact, reliable instruments. Semiconductor lasers for optical pumping and fast optical saturable absorbers, based on either semiconductor devices or the optical nonlinear Kerr effect, have dramatically improved these lasers and opened up new frontiers for applications with extremely short temporal resolution (much smaller than 10 fs), extremely high peak optical intensities (greater than 10 TW/cm2) and extremely fast pulse repetition rates (greater than 100 GHz).

60-W average power in 810-fs pulses from a thin-disk Yb:YAG laser

We demonstrate a passively mode-locked diode-pumped thin-disk Yb:YAG laser generating 810-fs pulses at 1030 nm with as much as 60 W of average output power (without using an amplifier). At a pulse repetition rate of 34.3 MHz, the pulse energy is 1.75 microJ and the peak power is as high as 1.9 MW. The beam quality is close to the diffraction limit, with M2 < 1.1.

240-fs pulses with 22-W average power from a mode-locked thin-disk Yb:KY(WO(4))(2) laser

We demonstrate what is to our knowledge the first passively mode-locked thin-disk Yb:KY(WO(4))(2) laser. The laser produces pulses of 240-fs duration with an average power of 22 W at a center wavelength of 1028 nm. At a pulse repetition rate of 25 MHz, the pulse energy is 0.9microJ , and the peak power is as high as 3.3 MW. The beam quality is very close to the diffraction limit, with M(2)=1.1 .