Design, characterization and experimental validation of a compact, flexible pulsed power architecture for ex vivo platelet activation

Ultra-Low Intensity Post-Pulse Affects Cellular Responses Caused by Nanosecond Pulsed Electric Fields

High-intensity nanosecond pulse electric fields (nsPEF) can preferentially induce various effects, most notably regulated cell death and tumor elimination. These effects have almost exclusively been shown to be associated with nsPEF waveforms defined by pulse duration, rise time, amplitude (electric field), and pulse number. Other factors, such as low-intensity post-pulse waveform, have been completely overlooked. In this study, we show that post-pulse waveforms can alter the cell responses produced by the primary pulse waveform and can even elicit unique cellular responses, despite the primary pulse waveform being nearly identical. We employed two commonly used pulse generator designs, namely the Blumlein line (BL) and the pulse forming line (PFL), both featuring nearly identical 100 ns pulse durations, to investigate various cellular effects. Although the primary pulse waveforms were nearly identical in electric field and frequency distribution, the post-pulses differed between the two designs. The BL's post-pulse was relatively long-lasting (~50 µs) and had an opposite polarity to the main pulse, whereas the PFL's post-pulse was much shorter (~2 µs) and had the same polarity as the main pulse. Both post-pulse amplitudes were less than 5% of the main pulse, but the different post-pulses caused distinctly different cellular responses. The thresholds for dissipation of the mitochondrial membrane potential, loss of viability, and increase in plasma membrane PI permeability all occurred at lower pulsing numbers for the PFL than the BL, while mitochondrial reactive oxygen species generation occurred at similar pulsing numbers for both pulser designs. The PFL decreased spare respiratory capacity (SRC), whereas the BL increased SRC. Only the PFL caused a biphasic effect on trans-plasma membrane electron transport (tPMET). These studies demonstrate, for the first time, that conditions resulting from low post-pulse intensity charging have a significant impact on cell responses and should be considered when comparing the results from similar pulse waveforms.

Dependence of Electric Pulse Mediated Growth Factor Release on the Platelet Rich Plasma Separation Method

Platelet rich plasma (PRP) has been explored for multiple clinical applications, including dentistry, orthopedics, sports medicine, diabetic foot ulcers, and cosmetic treatments. Topical applications of PRP typically use thrombin to induce platelet activation, which is accompanied by growth factor release and clotting of the PRP, prior to treatment. Injectable PRP treatments typically use non-activated PRP under the assumption that collagen at the site of the injury mediates platelet activation to ensure growth factor release in vivo. Ex-vivo electrical stimulation of platelets is emerging as a robust, easy to use, instrument-based PRP activation technique to facilitate growth factor release with or without clotting, while providing tunability of growth factor release, clot mechanical properties (when desired), and serotonin release from the dense granules. This paper briefly reviews the key results of the electrical activation of platelets and demonstrates successful growth factor release by electrical ex-vivo stimulation without clotting for three types of PRP separated from whole blood using available commercial kits: Harvest, EmCyte and Eclipse. While these three types of PRP feature a wide range of platelet and red blood cell content compared to whole blood, we demonstrate that pulsed electric fields enable growth factor release for all these biological matrices generated using whole blood from four human donors. These experiments open opportunities for using electrically stimulated PRP with released growth factors without clotting for injectable platelet treatments in relevant clinical applications.

Four Channel 6.5 kV, 65 A, 100 ns–100 µs Generator with Advanced Control of Pulse and Burst Protocols for Biomedical and Biotechnological Applications

Pulsed electric fields in the sub-microsecond range are being increasingly used in biomedical and biotechnology applications, where the demand for high-voltage and high-frequency pulse generators with enhanced performance and pulse flexibility is pushing the limits of pulse power solid state technology. In the scope of this article, a new pulsed generator, which includes four independent MOSFET based Marx modulators, operating individually or combined, controlled from a computer user interface, is described. The generator is capable of applying different pulse shapes, from unipolar to bipolar pulses into biological loads, in symmetric and asymmetric modes, with voltages up to 6.5 kV and currents up to 65 A, in pulse widths from 100 ns to 100 µs, including short-circuit protection, current and voltage monitoring. This new scientific tool can open new research possibility due to the flexibility it provides in pulse generation, particularly in adjusting pulse width, polarity, and amplitude from pulse-to-pulse. It also permits operating in burst mode up to 5 MHz in four independent channels, for example in the application of synchronized asymmetric bipolar pulses, which is shown together with other characteristics of the generator.

Activation of platelet-rich plasma by pulse electric fields: Voltage, pulse width and calcium concentration can be used to control and tune the release of growth factors, serotonin and hemoglobin

Activated platelet-rich plasma (PRP) has been used in the clinical settings of wound healing and regenerative medicine, with activation typically induced by the addition of bovine thrombin. To eliminate issues with availability, cost and potential side effects associated with bovine thrombin, ex vivo PRP activation using pulse electric fields (PEF) has been proposed and demonstrated. The present study characterizes the effect of PEF voltage and pulse width, in combination with a range of calcium concentrations, on clot formation, growth factor release, and serotonin (5-HT) release from dense granules. The main findings are: 1) increasing calcium concentrations with most PEF conditions leads to increased levels of PDGF and 5-HT release; 2) whether EGF levels increase or decrease with increasing calcium concentration depends on the specific PEF parameters; 3) the pattern of PDGF and EGF levels in supernatants suggest that these molecules are localized differently within platelets; 4) significant levels of PDGF, EGF, and 5-HT can be released without inducing clot formation or hemoglobin release. In conclusion, voltage, pulse width and calcium concentration can be used to control and tune the release of growth factors, serotonin and hemoglobin from PEF-activated PRP. Because growth factor requirements vary for different types of wounds and for wounds at different stages of healing, the unique balance of factors in supernatants of PEF-activated PRP may provide more clinically advantageous than the current standard of bovine thrombin-activated PRP.

Electrical stimulation of whole blood for growth factor release and potential clinical implications

Clinicians have increasingly applied platelet-rich plasma (PRP) for wound healing treatments. Topical treatments commonly require biochemical agents such as bovine thrombin to activate PRP ex vivo for clotting and growth factor release to facilitate healing upon application to the wound of interest. Recent studies have explored electrical stimulation as an alternative to bovine thrombin for PRP activation due to the former's cost, workflow complexity and potentially significant side effects; however, both approaches require separating the PRP from whole blood (WB) prior to activation. Eliminating the separation (typically centrifugation) step would reduce the cost and duration of the clinical procedure, which may be critical in trauma and surgical applications. We hypothesize that electric pulses (EPs) can release growth factors from WB, as they do from PRP, without requiring centrifugation of WB into PRP. A pilot study for two donors demonstrates the potential for EP stimulated growth factor release from WB. This motivates future experiments assessing EP parameter optimization for WB activation and in vivo studies to determine the clinical benefits for topical treatments and, especially, for injections in orthopedic applications that already utilize non-treated/non-activated WB.

Concepts and Capabilities of In-House Built Nanosecond Pulsed Electric Field (nsPEF) Generators for Electroporation: State of Art

Electroporation is a pulsed electric field triggered phenomenon of cell permeabilization, which is extensively used in biomedical and biotechnological context. There is a growing scientific demand for high-voltage and/or high-frequency pulse generators for electropermeabilization of cells (electroporators). In the scope of this article we have reviewed the basic topologies of nanosecond pulsed electric field (nsPEF) generators for electroporation and the parametric capabilities of various in-house built devices, which were introduced in the last two decades. Classification of more than 60 various nsPEF generators was performed and pulse forming characteristics (pulse shape, voltage, duration and repetition frequency) were listed and compared. Lastly, the trends in the development of the electroporation technology were discussed.

Nanosecond electric pulses rapidly enhance the inactivation of Gram-negative bacteria using Gram-positive antibiotics

Physically disrupting microorganism membranes to enable antibiotics to overcome resistance mechanisms that inhibit or excrete antibiotics has great potential for reducing antibiotic doses and rendering resistance mechanisms inert. We demonstrate the synergistic inactivation of a Gram-positive (Staphylococcus aureus) and two Gram-negative (Escherichia coli and Pseudomonas aeruginosa) bacteria by combining 222 30 kV/cm electric pulses (EPs) or 500 20 kV/cm EPs with 300-ns EP duration with various antibiotics with different mechanisms of action is demonstrated. Doses of antibiotics that produced no inactivation in 10 min of exposure in solution with bacteria induced several log reductions under the influence of nanosecond EPs. Combining 2 μg/L or 20 μg/mL of rifampicin with the 30 kV/cm EPs enhanced Staphylococcus aureus inactivation compared with EPs alone, while only a few of the other combinations demonstrated improvement. Combining 2 μg/L or 20 μg/mL of mupirocin or rifampicin with either EP train enhanced E. coli inactivation compared with EPs alone. Combining 2 μg/L or 20 μg/mL of erythromycin or vancomycin with the 30 kV/cm EPs enhanced E. coli inactivation compared with EPs alone. These results indicate that EPs can make Gram-positive antibiotics efficient for inactivating Gram-negative bacteria with future studies required to optimize EP parameters for other antibiotics and Gram-negative bacteria.

Validation of a SPICE Model for High Frequency Electroporation Systems

In this paper, we present an analysis and a validation of a simulation program with integrated circuit emphasis (SPICE) model for a pulse forming circuit of a high frequency electroporation system, which can deliver square-wave sub-microsecond (100–900 ns) electric field pulses. The developed SPICE model is suggested for use in evaluation of transient processes that occur due to high frequency operations in prototype systems. A controlled crowbar circuit was implemented to support a variety of biological loads and to ensure a constant electric pulse rise and fall time during electroporation to be independent of the applied buffer bioimpedance. The SPICE model was validated via a comparison of the simulation and experimental results obtained from the already existing prototype system. The SPICE model results were in good agreement with the experimental results, and the model complexity was found to be sufficient for analysis of transient processes. As result, the proposed SPICE model can be useful for evaluation and compensation of transient processes in sub-microsecond pulsed power set-ups during the development of new prototypes.

Nanosecond pulsed electric field induced proliferation and differentiation of osteoblasts and myoblasts

Low-intensity electric fields can induce changes in cell differentiation and cytoskeletal stresses that facilitate manipulation of osteoblasts and mesenchymal stem cells; however, the application times (tens of minutes) are of the order of physiological mechanisms, which can complicate treatment consistency. Intense nanosecond pulsed electric fields (nsPEFs) can overcome these challenges by inducing similar stresses on shorter timescales while additionally inducing plasma membrane nanoporation, ion transport and intracellular structure manipulation. This paper shows that treating myoblasts and osteoblasts with five 300 ns PEFs with intensities from 1.5 to 25 kV cm^-1 increased proliferation and differentiation. While nsPEFs above 5 kV cm^-1 decreased myoblast population growth, 10 and 20 kV cm^-1 trains increased myoblast population by approximately fivefold 48 h after exposure when all cell densities were set to the same level after exposure. Three trials of the PEF-treated osteoblasts showed that PEF trains between 2.5 and 10 kV cm^-1 induced the greatest population growth compared to the control 48 h after treatment. Trains of nsPEFs between 1.5 and 5 kV cm^-1 induced the most nodule formation in osteoblasts, indicating bone formation. These results demonstrate the potential utility for nsPEFs to rapidly modulate stem cells for proliferation and differentiation and motivate future experiments to optimize PEF parameters for in vivo applications.

The Transition to Paschen's Law for Microscale Gas Breakdown at Subatmospheric Pressure

The decrease in electronic device size necessitates greater understanding of gas breakdown and electron emission at microscale to optimize performance. While traditional breakdown theory using Paschen’s law (PL), driven by Townsend avalanche, fails for gap distance d \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\lesssim $$\end{document}≲ 15 μm, recent studies have derived analytic equations for breakdown voltage when field emission and Townsend avalanche drive breakdown. This study derives a new analytic equation that predicts breakdown voltage V_B within 4% of the exact numerical results of a previously derived theory and new experimental results at subatmospheric pressure for gap distances from 1–25 μm. At atmospheric pressure, V_B transitions to PL near the product of pressure and gap distance, pd, corresponding to the Paschen minimum; at lower pressures, the transition to PL occurs to the left of the minimum. We further show that the work function plays a major role in determining which side of the Paschen minimum V_B transitions to PL as pressure approaches atmospheric pressure while field enhancement and the secondary emission coefficient play smaller roles. These results indicate that appropriate combinations of these parameters cause V_B to transition to PL to the left of the Paschen minimum, which would yield an extended plateau similar to some microscale gas breakdown experimental observations.

Using extracellular calcium concentration and electric pulse conditions to tune platelet-rich plasma growth factor release and clotting

Platelet-rich plasma (PRP) is an emerging autologous biologic method for wound healing. Clinicians apply PRP either topically (where it is activated ex-vivo before treatment by adding an external agent to trigger clotting and the release of growth factors that facilitate wound healing) or through injection (where it is activated in vivo at the injury site with no prior activation before injection). Because topical PRP activation typically utilizes bovine thrombin, which has significant potential side effects and high costs, recent studies have assessed the efficacy of combining extracellular calcium (EC) and electric pulses (EPs) to activate PRP. The potential to apply this novel technique to PRP both topically and internally via injection raises the question about the ability to tune the clotting time and growth factor release for a given application. While previous studies have assessed the impact of applying EPs of various durations either directly (conductive coupling) or indirectly (capacitive coupling) to PRP containing EC, no studies have assessed the tunability of this activation based on modifying EP parameters, EP delivery method (conductive or capacitive coupling), and the EC concentration. We hypothesize that tuning these parameters will modify intracellular calcium uptake to permit the control of growth factor release and clotting time, which are critical for optimizing PRP for either topical or internal clinical applications. A pilot study for a single donor demonstrates the potential for tunability as a function of the intensity of membrane manipulation and calcium concentration, which facilitate the increase of cytosolic calcium. This motivates future studies assessing EC and EP optimization and in vivo studies to determine the overall efficacy of this tunability for wound healing.

Tunable activation of therapeutic platelet-rich plasma by pulse electric field: Differential effects on clot formation, growth factor release, and platelet morphology

BACKGROUND

Activation of platelet-rich plasma (PRP) by pulse electric field (PEF) releases growth factors which promote wound healing (e.g., PDGF, VEGF for granulation, EGF for epithelialization).

AIMS

To determine after PEF activation of therapeutic PRP: 1) platelet gel strength; 2) profile of released growth factors; 3) alpha- and T-granule release; 4) platelet morphology.

METHODS

Concentrated normal donor PRP was activated by 5 μsec (long) monopolar pulse, ~4000 V/cm (PEF A) or 150 nsec (short) bipolar pulse, ~3000 V/cm (PEF B) in the presence of 2.5 mM (low) or 20 mM (high) added CaCl2. Clot formation was evaluated by thromboelastography (TEG). Surface exposure of alpha granule (P-selectin) and T-granule (TLR9 and protein disulfide isomerase [PDI]) markers were assessed by flow cytometry. Factors in supernatants of activated PRP were measured by ELISA. Platelet morphology was evaluated by transmission electron microscopy (TEM).

RESULTS

Time to initial clot formation was shorter with thrombin (<1 min) than with PEF A and B (4.4-8.7 min) but clot strength (elastic modulus, derived from TEG maximum amplitude) was greater with PEF B than with either thrombin or PEF A (p<0.05). Supernatants of PRP activated with PEF A had higher EGF levels than supernatants from all other conditions. In contrast, levels of PF4, PDGF, and VEGF in supernatants were not significantly different after PEF A, PEF B, and thrombin activation. T-granule markers (TLR9 and PDI) were higher after thrombin than after PEF A or B with low or high CaCl2. By TEM, platelets in PEF-treated samples retained a subset of granules suggesting regulated granule release.

CONCLUSION

Pulse length and polarity can be modulated to produce therapeutic platelet gels as strong or stronger than those produced by thrombin, and this is tunable to produce growth factor profiles enhanced in specific factors important for different stages of wound healing.

Synergistic bacterial inactivation by combining antibiotics with nanosecond electric pulses

Antibiotic resistance mechanisms render current antibiotics ineffective, requiring higher concentrations of existing drugs or the development of more powerful drugs for infection treatment. This study demonstrates the synergistic inactivation of a gram-positive (Staphylococcus aureus) and a gram-negative (Escherichia coli) bacteria by combining either tobramycin or rifampicin with 300-ns electric pulses (EPs). For EPs depositing the same total energy density into the sample with no drug, higher electric fields induced greater inactivation, indicating a threshold for irreversible electroporation at these fields and membrane recovery in between lower intensity EPs. Synergistic inactivation generally increased with increasing drug concentration up to 20 μg/mL compared to strictly EP treatment. Combining even 1/20 of the clinical dose of tobramycin with a train of EPs induced between 2.5 and 3.5 log inactivation after only 10 min of exposure compared to hours to induce inactivation with a clinical dose with no EPs. Similarly, combining a train of EPs with a clinically relevant dose of rifampicin induced 7 to 9 log inactivation over the same time of exposure. These results indicate the promise of combining EPs with antibiotics to rapidly inactivate antibiotic-resistant bacteria in localized treatment areas.