USE OF WARFARIN IN PEDIATRICS: CLINICAL AND PHARMACOLOGICAL CHARACTERISTICS

Direct oral anticoagulant therapy in adolescent venous thromboembolism: A systematic review

Adolescent venous thromboembolism (VTE) has unique challenges in management, complications, and compliance to anticoagulants. Direct oral anticoagulants (DOACs) have been approved for pediatric VTE management, with an increasing use especially in adolescents. Primary objective is to evaluate the safety and efficacy of DOAC therapy in adolescent VTE. Secondary objectives include adverse events, bleeding events, and overall mortality. A SR protocol was registered in PROSPERO 2022 (CRD42022363928). Databases were searched from inception to September 22, 2022. Studies with children aged 10-18 years, VTE diagnosis, DOAC therapy, randomized control trials (RCTs), cohort, and relevant study types were included. Studies including prophylaxis, non-DOAC therapy, arterial thrombosis, age outliers, non-relevant study types were excluded. Findings are reported in accordance to PRISMA 2020. Nine reports from five studies, published between 2016 and 2022, were included. Rivaroxaban was the most common DOAC. VTE recurrence was 0.02% in the rivaroxaban phase III trial and one patient in the dabigatran phase IIb/III trial. Complete/partial thrombus resolution (CR/PR) was 76.6% in the rivaroxaban phase III trial, and 83.9% in the dabigatran phase IIb/III trial. CR/PR was found to be 68.4% in Dhaliwal et al. study and 83.3% in Hassan et al. study. Major bleeding occurred in one patient. Headache and gastrointestinal symptoms were commonly seen. All-cause mortality occurred in a patient due to cancer progression. DOAC therapy in adolescent VTE had CR/PR in two-thirds of the patients, with low incidence of VTE recurrence and major bleeding. As there are only two randomized controlled trial (RCTs), future adolescents' studies are required to validate our results.

Towards Printed Pediatric Medicines in Hospital Pharmacies: Comparison of 2D and 3D-Printed Orodispersible Warfarin Films with Conventional Oral Powders in Unit Dose Sachets

To date, the lack of age-appropriate medicines for many indications results in dose manipulation of commercially available dosage forms, commonly resulting in inaccurate doses. Various printing technologies have recently been explored in the pharmaceutical field due to the flexible and precise nature of the techniques. The aim of this study was, therefore, to compare the currently used method to produce patient-tailored warfarin doses at HUS Pharmacy in Finland with two innovative printing techniques. Dosage forms of various strengths (0.1, 0.5, 1, and 2 mg) were prepared utilizing semisolid extrusion 3D printing, inkjet printing and the established compounding procedure for oral powders in unit dose sachets (OPSs). Orodispersible films (ODFs) drug-loaded with warfarin were prepared by means of printing using hydroxypropylcellulose as a film-forming agent. The OPSs consisted of commercially available warfarin tablets and lactose monohydrate as a filler. The ODFs resulted in thin and flexible films showing acceptable ODF properties. Moreover, the printed ODFs displayed improved drug content compared to the established OPSs. All dosage forms were found to be stable over the one-month stability study and suitable for administration through a naso-gastric tube, thus, enabling administration to all possible patient groups in a hospital ward. This work demonstrates the potential of utilizing printing technologies for the production of on-demand patient-specific doses and further discusses the advantages and limitations of each method.

Formulation development of a continuously manufactured orodispersible film containing warfarin sodium for individualized dosing

Continuously manufactured orodispersible films (ODFs) offer a promising approach for individualized therapy with an easy to administer solid dosage form. The aim of this study was to develop a long ODF containing warfarin sodium to enable safe and more flexible dosing. Formulation development was conducted systematically for the continuous film coating process. A continuously working pilot-scale coating bench was used for film manufacturing and the viscosities of the polymer solutions were investigated to obtain processible formulations. The investigation of the mechanical properties of the long film was an integral part of the study, because the handling of the long film during flexible dosing differs distinctly from the handling of a single dosed ODF. The secant modulus and the yield stress were evaluated as parameters with high information value about the deformation behavior of the ODF. A long warfarin ODF was successfully produced using the pilot-scale coating bench equipped with an optical probe for in-line film thickness measurement. It was feasible to use the principle of a tape dispenser for flexible and, therefore, individualized dosing as proof of concept. Combining the long ODF with a dosing device allows individualized therapy with warfarin for all age groups manageable by the patient himself.