Effect of cyclic load on vertical misfit of prefabricated and cast implant single abutment

Micro-CT Evaluation of Microgaps at Implant-Abutment Connection

The assessment of microgaps at the implant-abutment interface is an important factor that may influence clinical success. Thus, the aim of this study was to evaluate the size of microgaps between prefabricated and customised abutments (Astra Tech, Dentsply, York, PA, USA; Apollo Implants Components, Pabianice, Poland) mounted on a standard implant. The measurement of the microgap was performed using micro-computed tomography (MCT). Due to 15-degree rotation of samples, 24 microsections were obtained. Scans were performed at four levels established at the interface between the abutment and the implant neck. Moreover, the volume of the microgap was evaluated. The size of the microgap at all measured levels varied from 0.1 to 3.7 µm for Astra and from 0.1 to 4.9 µm for Apollo (p > 0.05). Moreover, 90% of the Astra specimens and 70% of the Apollo specimens did not exhibit any microgaps. The highest mean values of microgap size for both groups were detected at the lowest portion of the abutment (p > 0.05). Additionally, the average microgap volume was greater for Apollo than for Astra (p > 0.05). It can be concluded that most samples did not exhibit any microgaps. Furthermore, the linear and volumetric dimensions of microgaps observed at the interface between Apollo or Astra abutments and Astra implants were comparable. Additionally, all tested components presented microgaps (if any) that were clinically acceptable. However, the microgap size of the Apollo abutment was higher and more variable than that of the Astra one.

Effects of Occlusal Scheme on All-on-Four Abutments, Screws, and Prostheses: A Three-Dimensional Finite Element Study

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, because of the potential impact of occlusal loads on implant prosthetic components. The aim of the present 3D finite element analysis (FEA) study was to investigate the stresses on abutments, screws, and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. 3D models of the maxilla, mandible, implants, implant substructures, and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO), and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained, and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments, and prostheses in the All-on-Four concept.

Influence of eccentric cyclic loading on implant components: Comparison between titanium and zirconia abutments

The objective of this study was to investigate the effects of eccentric cyclic loading on implant components using the internal joint system with titanium and zirconia abutments. Abutments were made of either pure titanium (Ti group) or zirconia (TZP group). Cyclic loading test was conducted according to the specifications of ISO 14801. Loading condition was at 2 points assuming axial load and eccentric load. The reverse torque value reduced after the eccentric load and reduced more in the TZP group than the Ti group. Marginal gap changed after eccentric loading, and was greater in the TZP group. In the TZP group, changes in configuration were observed in the implant body, and Ti was detected on the abutment surface. From the above, the eccentric load may have worse effects than axial loads. It was suggested that the TZP group was clinically disadvantageous compared to the Ti group.

Compatibility of Nonoriginal Abutments With Implants: Evaluation of Microgap at the Implant-Abutment Interface, With Original and Nonoriginal Abutments

PURPOSE

The purpose of this study was to evaluate the fit of nonoriginal abutments to implants at the implant abutment junction.

MATERIALS AND METHODS

Twenty titanium implants from a single manufacturer were randomly divided into 2 groups of ten each. Ten titanium premachined original abutments (group I) and ten titanium premachined nonoriginal abutments (from different manufacturer-group II) were connected to the implants with the recommended manufacturer torque level and then embedded into autopolymerizing clear acrylic resin blocks. After overnight curing, these blocks were vertically sectioned using water jet sectioning machine and evaluated under scanning electron microscope following the sequential cleaning procedures. The microgap at the implant-abutment interface for all the samples was measured using pixel counting software and subjected to statistical analysis using nonparametric Mann-Whitney U test.

RESULTS

The mean microgap at the implant-abutment interface at the external, middle, and internal points was 1.597, 1.399, and 1.831 µm, respectively, for group I and 2.395, 2.488, and 3.339 µm, respectively, for group II samples. Nonparametric Mann-Whitney U test showed statistically significant difference between 2 groups at the midpoint for the nonoriginal abutments compared with the original ones.

CONCLUSION

Within the limitations of the study, the mean microgap at the implant-abutment interface at the platform level at the external, middle, and internal points for both original abutments and nonoriginal abutments was found to be within clinically acceptable limits.

Microscopic evaluation of implant platform adaptation with UCLA-type abutments: in vitro study

Abstract Introduction The fit between abutment and implant is crucial to determine the longevity of implant-supported prostheses and the maintenance of peri-implant bones. Objective To evaluate the vertical misfit between different abutments in order to provide information to assist abutment selection. Material and method UCLA components (N=40) with anti-rotational system were divided as follows: components usinated in titanium (n=10) and plastic components cast proportionally in titanium (n=10), nickel-chromium-titanium-molybdenum (n=10) and nickel-chromium (n=10) alloys. All components were submitted to stereomicroscope analysis and were randomly selected for characterization by SEM. Result Data were analyzed using mean and standard deviation and subjected to ANOVA-one way, where the groups proved to statistically different (p=<0.05), followed by Tukey’s test. Conclusion The selection of material influences the value of vertical misfit. The group machined in Ti showed the lowest value while the group cast in Ni Cr showed the highest value of vertical misfit.

Influence of torsional strength on different types of dental implant platforms

AIM

The study assessed deformation of implant components submitted to torsion tests of 80 and 120 N · cm using an optical stereomicroscope.

MATERIAL AND METHODS

The following 3 types of Titaniumfix conical implant connections (n = 5) measuring Ø 4.0 × 11.5 mm were used: external, internal hexagon and Morse taper connections. The diagonal and lateral measurements of the hexagon implant platform were measured before and after the torsion test.

RESULTS

The torsion test using torque of 80 and 120 N · cm altered the implant dental platforms. All groups presented deformation of implant component after torque of 80 N · cm with no statistical difference among them. During torque of 120 N · cm, a difference in the Morse taper connection in relation to the internal and external hexagon connection was observed. The Morse taper connection implant, followed by the internal hex implant, underwent less deformation. Greater deformation occurred in the external hex implants.

CONCLUSION

For all the implants, high insertion torques deformed the implant platform preventing long-term maintenance and stability of implants.

Is the internal connection more efficient than external connection in mechanical, biological, and esthetical point of views? A systematic review

PURPOSE

This systematic review aimed to evaluate if the internal connection is more efficient than the external connection and its associated influencing factors.

METHODS

A specific question was formulated according to the Population, Intervention, Control, and Outcome (PICO): Is internal connection more efficient than external connection in mechanical, biological, and esthetical point of views? An electronic search of the MEDLINE and the Web of Knowledge databases was performed for relevant studies published in English up to November 2013 by two independent reviewers. The keywords used in the search included a combination of "dental implant" and "internal connection" or "Morse connection" or "external connection." Selected studies were randomized clinical trials, prospective or retrospective studies, and in vitro studies with a clear aim of investigating the internal and/or external implant connection use.

RESULTS

From an initial screening yield of 674 articles, 64 potentially relevant articles were selected after an evaluation of their titles and abstracts. Full texts of these articles were obtained with 29 articles fulfilling the inclusion criteria. Morse taper connection has the best sealing ability. Concerning crestal bone loss, internal connections presented better results than external connections. The limitation of the present study was the absence of randomized clinical trials that investigated if the internal connection was more efficient than the external connection.

CONCLUSIONS

The external and internal connections have different mechanical, biological, and esthetical characteristics. Besides all systems that show proper success rates and effectiveness, crestal bone level maintenance is more important around internal connections than external connections. The Morse taper connection seems to be more efficient concerning biological aspects, allowing lower bacterial leakage and bone loss in single implants, including aesthetic regions. Additionally, this connection type can be successfully indicated for fixed partial prostheses and overdenture planning, since it exhibits high mechanical stability.

Wear of double crown systems: electroplated vs. casted female part

OBJECTIVES

The wear of telescopic crowns is a common problem often reducing the patient's satisfaction with the denture and resulting in a renewal of the denture. The study aims to compare the wear behavior of conical crowns using electroplated copings (group E ) with standard telescopic crowns with cast female parts (group C).

MATERIAL AND METHODS

10 conical crowns were milled for each group of a cast gold alloy. The specimen of group E had a conicity of 2º. The cast secondary crowns of group C had a 0º design. The electroplated coping was established by direct electroforming. An apparatus accomplishing 10,000 wear cycles performed the wear test. The retentive forces and the correlating distance during insertion and separation were measured. The wear test was separated in a start phase, an initial wear phase and the long term wear period. The retention force value and the force-distance integral of the first 0.33 mm of each cycle were calculated.

RESULTS

The retentive forces were significantly higher for group E and the integrals were significantly lower for this group except the integral at cycle 10,000. The changes of retention force and integral did not differ significantly between both groups in all phases. The change of the integrals as well as the integral at the particular cycles showed higher interquartile distances for group C.

CONCLUSIONS

Within the limitations of this study the tested conical crowns showed clinically acceptable retentive properties. The values reached a range comparable to retentive elements tested in recent literature. The values of group C showed higher ranges. The force measured for group E was significantly higher than for group C but the integrals showed an opposite tendency. The results indicate that an exclusive analysis of the force is not sufficient as the integral is not equivalent to the force although it describes the retentive property of the system in a better way than the force over a distance is described. Both systems seem to be suitable for clinical practice.