Validation and use of a finite element model of C-2 for determination of stress and fracture patterns of anterior odontoid loads

Internal Morphology of the Odontoid Process: Anatomic and Imaging Study with Application to C2 Fractures

OBJECTIVE

Fracture of the odontoid process is a critical injury to diagnose and often treat. The aim of this anatomic study was to present a comprehensive understanding of this part of the C2 vertebra.

METHODS

We used 20 C2 vertebrae. Samples underwent imaging (computed tomography [CT] with and without three-dimensional reconstruction, micro-CT, 1.5T magnetic resonance imaging) and sagittal and coronal sectioning using a bone saw. Sectioned specimens were imaged under a digital handheld microscope, and transillumination of the bone was used to highlight its internal trabecular pattern. Three samples underwent infusion of the odontoid process with a hardening substance and were then decalcified.

RESULTS

Internal trabecular patterns of the odontoid process of all specimens were discernible. In sagittal and coronal sections, trabecular patterns were highlighted with transillumination, but the patterns were much clearer using the digital microscope. Magnetic resonance imaging and CT provided the least detail of the imaging methods, but the trabecular patterns could be identified. Three-dimensional reconstruction of CT data was the preferred imaging method over magnetic resonance imaging and CT without three-dimensional reconstruction. The most distinct trabecular and cortical patterns were seen using micro-CT. Osteoporosis was seen in 2 specimens (10%). Five specimens (25%) were found to have a subdental synchondrosis. For most specimens, the trabeculae were found throughout the odontoid process.

CONCLUSIONS

Improved knowledge of the anatomy, structural composition, and variations within the C2 vertebra may allow for better treatment options and patient care.

Characteristics and prediction of cranial crush injuries in children

This study documents four clinical cases of fatal crush injuries to children between 1.5 and 6 years of age with correlations between modeled stress and clinically observed fracture patterns. The clinical case fractures were concentrated in the basicranium, bridged the impact sites, and traversed the middle cranial fossa in the area of the spheno-occipital synchondrosis. The crushing forces from these cases were recreated on a simplified finite element model of a cranium by applying bilateral pressures to corresponding regions. Numerous trials were run to develop a representative pattern of principal stress directions. In all cases, the highest tensile stresses were located on the basicranium and corresponded to the observed fracture path(s). These results suggest that prefailure stress field diagrams may predict fracture propagation paths, although these will not be exact. Also, these analyses indicate that quasi-static bilateral loading of the cranium may lead to predictable fracture of the basicranium.

Initial stability of cervical spine fixation: predictive value of a finite element model. Technical note

The purpose of this study was to generate a validated finite element (FE) model of the human cervical spine to be used to analyze new implants. Digitized data obtained from computerized tomography scanning of a human cervical spine were used to generate a three-dimensional, anisotropic, linear C5-6 FE model by using a software package (ANSYS 5.4). Based on the intact model (FE/Intact), a second was generated by simulating an anterior cervical fusion and plate (ACFP) C5-6 model in which monocortical screws (FE/ACFP) were used. Loading of each FE model was simulated using pure moments of +/- 2.5 Nm in flexion/extension, axial left/right rotation, and left/right lateral bending. For validation of the models, their predicted C5-6 range of motion (ROM) was compared with the results of an earlier, corresponding in vitro study of six human spines, which were tested in the intact state and surgically altered at C5-6 with the same implants. The validated model was used to analyze the stabilizing effect of a new disc spacer, Cenius (Aesculap AG, Tuttlingen, Germany), as a stand-alone implant (FE/Cenius) and in combination with an anterior plate (FE/Cenius+ACFP). In addition, compression loads at the upper surface of the spacer were investigated using both models. As calculated by FE/Intact and FE/ACFP models, the ROM was within 1 standard deviation of the mean value of the corresponding in vitro measurements for each loading case. The FE/Cenius model predicted C5-6 ROM values of 5.5 degrees in flexion/extension, 3.1 degrees in axial rotation (left and right), and 2.9 degrees in lateral bending (left and right). Addition of an anterior plate resulted in a further decrease of ROM in each loading case. The FE/Cenius model predicted an increase of compression load in flexion and a decrease in extension, whereas in the FE/Cenius+ACFP model an increase of graft compression in extension and unloading of the graft in flexion were predicted. The current FE model predicted ROM values comparable with those obtained in vitro in the intact state as well as after simulation of an ACFP model. It predicted a stabilizing potential for a new cage, alone and in combination with an anterior plate system, and predicted the influence of both loading modality and additional instrumentation on the behavior of the interbody graft.