A Novel Biosorbent From Hardwood Cellulose Nanofibrils Grafted With Poly(m-Aminobenzene Sulfonate) for Adsorption of Cr(VI)

Decoration of sodium carboxymethylcellulose gel microspheres with modified lignin to enhanced methylene blue removal

The introduction of active groups from biomass is currently the most promising alternative method for increasing the adsorption effect of dyes. In this study, modified aminated lignin (MAL) rich in phenolic hydroxyl and amine groups was prepared by amination and catalytic grafting. The factors influencing the modification conditions of the content of amine and phenolic hydroxyl groups were explored. Chemical structural analysis results confirmed that MAL was successfully prepared using a two-step method. The content of phenolic hydroxyl groups in MAL significantly increased to 1.46 mmol/g. MAL/sodium carboxymethylcellulose (NaCMC) gel microspheres (MCGM) with enhanced methylene blue (MB) adsorption capacity owing to the formation of a composite with MAL were synthesized by a sol-gel process followed by freeze-drying and using multivalent cations Al³⁺ as cross-linking agents. In addition, the effects of the MAL to NaCMC mass ratio, time, concentration, and pH on the adsorption of MB were explored. Benefiting from a sufficient number of active sites, MCGM exhibited an ultrahigh adsorption capacity for MB removal, and the maximum adsorption capacity was 118.30 mg/g. These results demonstrated the potential of MCGM for wastewater treatment applications.

Preparation and modification of nanocellulose and its application to heavy metal adsorption: A review

Heavy metals are a notable pollutant in aquatic ecosystems that results in many deadly diseases of the human body after enrichment through the food chain. As an environmentally friendly renewable resource, nanocellulose can be competitive with other materials at removing heavy metal ions due to its large specific surface area, high mechanical strength, biocompatibility and low cost. In this review, the research status of modified nanocellulose for heavy metal adsorbents is primarily reviewed. Two primary forms of nanocellulose are cellulose nanocrystals (CNCs) and cellulose nanofibers (CNFs). The preparation process of nanocellulose was derived from natural plants, and the preparation process included noncellulosic constituent removal and extraction of nanocellulose. Focusing on heavy metal adsorption, the modification of nanocellulose was explored in depth, including direct modification methods, surface grafting modification methods based on free radical polymerization and physical activation. The adsorption principles of nanocellulose-based adsorbents when removing heavy metals are analyzed in detail. This review may further facilitate the application of the modified nanocellulose in the field of heavy metal removal.

Asymmetric Alternative Current Electrochemical Method Coupled with Amidoxime-Functionalized Carbon Felt Electrode for Fast and Efficient Removal of Hexavalent Chromium from Wastewater

A large amount of Cr (VI)-polluted wastewater produced in electroplating, dyeing and tanning industries seriously threatens water ecological security and human health. Due to the lack of high-performance electrodes and the coulomb repulsion between hexavalent chromium anion and cathode, the traditional DC-mediated electrochemical remediation technology possesses low Cr (VI) removal efficiency. Herein, by modifying commercial carbon felt (O-CF) with amidoxime groups, amidoxime-functionalized carbon felt electrodes (Ami-CF) with high adsorption affinity for Cr (VI) were prepared. Based on Ami-CF, an electrochemical flow-through system powered by asymmetric AC was constructed. The mechanism and influencing factors of efficient removal of Cr (VI) contaminated wastewater by an asymmetric AC electrochemical method coupling Ami-CF were studied. Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR), and X-ray photoelectron spectroscopy (XPS) characterization results showed that Ami-CF was successfully and uniformly loaded with amidoxime functional groups, and the adsorption capacity of Cr (VI) was more than 100 times higher than that of O-CF. In particular, the Coulomb repulsion effect and the side reaction of electrolytic water splitting were inhibited by the high-frequency anode and cathode switching (asymmetric AC), the mass transfer rate of Cr (VI) from electrode solution was increased, the reduction efficiency of Cr (VI) to Cr (III) was significantly promoted and a highly efficient removal of Cr (VI) was achieved. Under optimal operating conditions (positive bias 1 V, negative bias 2.5 V, duty ratio 20%, frequency 400 Hz, solution pH = 2), the asymmetric AC electrochemistry based on Ami-CF can achieve fast (30 s) and efficient removal (>99.11%) for 0.5-100 mg·L^-1 Cr (VI) with a high flux of 300 L h^-1 m^-2. At the same time, the durability test verified the sustainability of the AC electrochemical method. For Cr (VI)-polluted wastewater with an initial concentration of 50 mg·L^-1, the effluent concentration could still reach drinking water grade (<0.05 mg·L^-1) after 10 cycling experiments. This study provides an innovative approach for the rapid, green and efficient removal of Cr (VI) containing wastewater at low and medium concentrations.

Eco-friendly and facile preparation of chitosan-based biofilms of novel acetoacetylated lignin for antioxidant and UV-shielding properties

The development of eco-friendly, sustainable, biodegradable, and biocompatible green biopolymer composites is becoming increasingly important. In this study, acetoacetylated lignin (ATL) was obtained via an eco-friendly, facile one-step synthesis reaction, and chitosan (CS)-containing ATL films (CSL) were prepared. The chemical structural analysis of ATL confirmed that the acetoacetyl groups were successfully grafted onto kraft lignin (KL). ATL with adequate acetoacetyl groups exhibited enhanced molecular weight and antioxidant and ultraviolet (UV)-shielding properties. In particular, ATL, with a half maximal inhibitory concentration (IC₅₀) of 23.8 μg·mL^-1, exhibited superior antioxidant activity than butylated hydroxytoluene (38.3 μg·mL^-1) and KL (50.0 μg·mL^-1). When ATL was incorporated into the CS solution to prepare biofilms, the antioxidant activity, UV-shielding property, water resistance, and thermal stability of the CSL greatly improved. Notably, the UV-A and UV-B shielding properties of the 2 % CSL were 130 % and 78 % higher than those of the pure CS film, respectively. Therefore, ATL designed with lignin-derived multifunctional properties has potential applications as an antioxidant and UV-shielding bio-additive and shows significant prospects in food packaging and biomedical applications.

Advances in Sorptive Removal of Hexavalent Chromium (Cr(VI)) in Aqueous Solutions Using Polymeric Materials

Sorptive removal of hexavalent chromium (Cr(VI)) bears the advantages of simple operation and easy construction. Customized polymeric materials are the attracting adsorbents due to their selectivity, chemical and mechanical stabilities. The mostly investigated polymeric materials for removing Cr(VI) were reviewed in this work. Assembling of robust functional groups, reduction of self-aggregation, and enhancement of stability and mechanical strength, were the general strategies to improve the performance of polymeric adsorbents. The maximum adsorption capacities of these polymers toward Cr(VI) fitted by Langmuir isotherm model ranged from 3.2 to 1185 mg/g. Mechanisms of complexation, chelation, reduction, electrostatic attraction, anion exchange, and hydrogen bonding were involved in the Cr(VI) removal. Influence factors on Cr(VI) removal were itemized. Polymeric adsorbents performed much better in the strong acidic pH range (e.g., pH 2.0) and at higher initial Cr(VI) concentrations. The adsorption of Cr(VI) was an endothermic reaction, and higher reaction temperature favored more robust adsorption. Anions inhibited the removal of Cr(VI) through competitive adsorption, while that was barely affected by cations. Factors that affected the regeneration of these adsorbents were summarized. To realize the goal of industrial application and environmental protection, removal of the Cr(VI) accompanied by its detoxication through reduction is highly encouraged. Moreover, development of adsorbents with strong regeneration ability and low cost, which are robust for removing Cr(VI) at trace levels and a wider pH range, should also be an eternally immutable subject in the future. Work done will be helpful for developing more robust polymeric adsorbents and for promoting the treatment of Cr(VI)-containing wastewater.