Impact of Modeling Assumptions on Stability Predictions in Reverse Total Shoulder Arthroplasty

Effect of RSA glenoid baseplate central fixation on micromotion and bone stress

Background

In reverse shoulder arthroplasties (RSA), osseous in-growth is promoted if glenoid micromotion does not exceed 150 μm. The purpose of this study was to determine whether the configuration of central fixation for RSA glenoid baseplates reduces implant micromotion or changes scapula bone stresses.

Methods

Using finite element analysis, glenoid baseplate fixation was tested in a cohort of 3 male and 2 female patients who were to undergo RSA. Computer models were created for 3 different RSA glenoid baseplate and 84 glenosphere designs, a central threaded peg (1 variant, D-TP), a central unthreaded peg (2 variants, I- 85 P(15) and I-P(25)), and a central peg with a screw (2 variants, A-PS and I-PS). A compressive and shear force of 756 N was distributed across the glenosphere with the scapula anchored.

Results

Displacement was within 20-130 μm at the glenosphere baseplate-bone interface for all baseplates. The glenospheres with unthreaded pegs had intermediate displacement values (I-P(15): median, 89 μm; range, 32-112 μm; and I-P(25): median, 93 μm; range, 31-109 μm). The von Mises stresses were 1.8-7.0 MPa within cortical bone and 0.6-1.6 MPa within trabecular bone. Cortical bone stresses were similar with unthreaded pegs (I-P(15): median, 4.2 MPa; range, 1.8-6.0 MPa; and I-P(25): median, 4.2 MPa; range, 1.8-6.1 MPa), whereas mean trabecular stresses were similar for all configurations.

Conclusions

All configurations yielded adequate stability, with micromotions being below 150 μm. The unthreaded pegged designs provided a valid alternative to the stable threaded pegged convex baseplates in terms of micromotions and bone stresses.

Pre-Operative CT-Based Planning Integrated With Intra-Operative Navigation in Reverse Shoulder Arthroplasty: Data Acquisition and Analysis Protocol, and Preliminary Results of Navigated Versus Conventional Surgery

Reverse total shoulder arthroplasty (RSA) successfully restores shoulder function in different conditions. Glenoid baseplate fixation and positioning seem to be the most important factors influencing RSA survival. When scapular anatomy is distorted (eccentric osteoarthrirtis, rotator cuff arthropathy), optimal baseplate positioning and secure screw purchase can be challenging. The aim of this study was to evaluate whether CT-based pre-operative planning, integrated with intra-operative navigation could improve glenoid baseplate fixation and positioning by increasing screw length, reducing number of screws required to obtain fixation and increasing the use of augmented baseplate to gain the desired positioning. Twenty patients who underwent navigated RSA were compared retrospectively with 20 patients operated on with a conventional technique. All the procedures were performed by the same surgeon, using the same implant. Mean screw length was significantly longer in the navigation group (35.5 ± 4.4 mm vs 29.9 ± 3.6 mm; p = .001). Significant higher rate of optimal fixation using 2 screws only (17 vs 3 cases, p = .019) and higher rate of augmented baseplate usage (13 vs 4 cases, p = .009) was also present in the navigation group. Pre-operative CT-based planning integrated with intra-operative navigation can improve glenoid component positioning and fixation, possibly leading to an improvement of RSA survival.

Finite Element Analysis of Custom Shoulder Implants Provides Accurate Prediction of Initial Stability

Custom reverse shoulder implants represent a valuable solution for patients with large bone defects. Since each implant has unique patient-specific features, finite element (FE) analysis has the potential to guide the design process by virtually comparing the stability of multiple configurations without the need of a mechanical test. The aim of this study was to develop an automated virtual bench test to evaluate the initial stability of custom shoulder implants during the design phase, by simulating a fixation experiment as defined by ASTM F2028-14. Three-dimensional (3D) FE models were generated to simulate the stability test and the predictions were compared to experimental measurements. Good agreement was found between the baseplate displacement measured experimentally and determined from the FE analysis (Spearman’s rank test, p < 0.05, correlation coefficient ρs = 0.81). Interface micromotion analysis predicted good initial fixation (micromotion <150 µm, commonly used as bone ingrowth threshold). In conclusion, the finite element model presented in this study was able to replicate the mechanical condition of a standard test for a custom shoulder implants.

Influence of reverse total shoulder arthroplasty baseplate design on torque and compression relationship

Background

A linear relationship between baseplate insertion torque and compression force in reverse shoulder arthroplasty (RSA) baseplates with central screw design has been recently established. In this study, we evaluated 3 different baseplate designs and their influence on the torque-compression relationship.

Methods

Three different RSA baseplate designs were evaluated through biomechanical testing using a glenoid vault, bone surrogate model. A digital torque gauge was used to measure insertion torque applied to the baseplate, whereas compression data were collected continuously from a load cell. Additionally, 2 predictive models were developed to predict the compression forces of each baseplate design at varying levels of torque.

Results

A linear relationship was found between baseplate compression and insertion torque for all 3 baseplate designs. Both the monoblock and 2-piece locking designs achieved the goal torque of 6.8 Nm, whereas the 2-piece nonlocking design did not due to material strip-out. No significant difference in maximum compression was found between the monoblock and 2-piece locking designs. However, the 2-piece nonlocking design achieved significantly higher compression. Both predictive models were shown to adequately predict compressive forces at different torque inputs for the monoblock and 2-piece locking designs but not the 2-piece nonlocking design.

Conclusion

The torque-compression relationship of a central screw baseplate is significantly affected by baseplate design. A 2-piece nonlocking baseplate reaches higher compression levels and risks material strip-out at lower insertional torques compared with a monoblock and 2-piece locking design. This has implications both on component design and on surgeon tactile feedback during surgery.