A Survey on Design and Control of Lower Extremity Exoskeletons for Bipedal Walking

Application of Fuzzy Adaptive Impedance Control Based on Backstepping Method for PAM Elbow Exoskeleton in Rehabilitation

In this study, a fuzzy adaptive impedance control method integrating the backstepping control for the PAM elbow exoskeleton was developed to facilitate robot-assisted rehabilitation tasks. The proposed method uses fuzzy logic to adjust impedance parameters, thereby optimizing user adaptability and reducing interactive torque, which are major limitations of traditional impedance control methods. Furthermore, a repetitive learning algorithm and an adaptive control strategy were incorporated to improve the performance of position accuracy, addressing the time-varying uncertainties and nonlinear disturbances inherent in the exoskeleton. The stability of the proposed controller was tested, and then corresponding simulations and an elbow flexion and extension rehabilitation experiment were performed. The results showed that, with the proposed method, the root mean square of the tracking error was 0.032 rad (i.e., 21.95% less than that of the PID method), and the steady-state interactive torque was 1.917 N·m (i.e., 46.49% less than that of the traditional impedance control). These values exceeded those of the existing methods and supported the potential application of the proposed method for other soft actuators and robots.

Walking on Real-world Terrain with an Ankle Exoskeleton in Cerebral Palsy

Despite medical treatment focused on addressing walking disability, many millions of people with neurological conditions, like cerebral palsy (CP), struggle to maintain independent mobility. Lower limb exoskeletons and exosuits may hold potential for augmenting walking ability. However, it remains unknown whether these wearable robots are safe and beneficial for use outside of highly controlled laboratory environments, the demonstration of which is necessary for clinical translation. Here, we show that a lightweight, portable, ankle exoskeleton with an adaptable one-size-works-for-all assistance controller can improve energy efficiency and walking speed for individuals with CP spanning a wide spectrum of lower limb impairment in a multi-terrain real-world environment. Tested on an outdoor walking route with level, sloped, and stair terrain, robotic assistance resulted in a 15-18% (p = 0.013-0.026) reduction in estimated energy cost and a 7-8% (p = 0.001-0.004) increase in average walking speed across "shorter" 6-minute and "longer" 20-minute walking durations relative to unassisted walking. This study provides evidence that wearable robots may soon improve mobility in neighborhood, school, and community settings for individuals with CP.

Analysis of contact pressure in a 3D model of dual-mobility hip joint prosthesis under a gait cycle

Hip joint prostheses are used to replace hip joint function in the human body. The latest dual-mobility hip joint prosthesis has an additional component of an outer liner that acts as a cover for the liner component. Research on the contact pressure generated on the latest model of a dual-mobility hip joint prosthesis under a gait cycle has never been done before. The model is made of ultrahigh molecular weight polyethylene (UHMWPE) on the inner liner and 316L stainless steel (SS 316L) on the outer liner and acetabular cup. Simulation modeling using the finite element method is considered static loading with an implicit solver for studying the geometric parameter design of dual-mobility hip joint prostheses. In this study, simulation modeling was carried out by applying varying inclination angles of 30°, 40°, 45°, 50°, 60°, and 70° to the acetabular cup component. Three-dimensional loads were placed on femoral head reference points with variations of femoral head diameter used at 22 mm, 28 mm, and 32 mm. The results in the inner surface of the inner liner, the outer surface of the outer liner, and the inner surface of the acetabular cup showed that the variations in inclination angle do not have a major effect on the maximum contact pressure value on the liner component, where the acetabular cup with an inclination angle of 45° can reduce contact pressure more than the other studied inclination angle variations. In addition, it was found that the 22 mm diameter of the femoral head increases the contact pressure. The use of a larger diameter femoral head with an acetabular cup configuration at a 45° inclination can minimize the risk of implant failure due to wear.

Exoskeletons: A challenge for development

The development of exoskeletons is currently a lengthy process full of challenges. We are proposing a framework to accelerate the process and make the resulting exoskeletons more user-centered. The needed accomplishments in science are described in an effort to lay the foundation for future research projects. Since the early 2000s, exoskeletons have been discussed as an emerging technology in industrial, medical, or military applications. Those systems are designed to support people during manual tasks. At first, those systems lacked broad acceptance. Many models found their niches in ongoing developments and more diverse systems entering the market. There are still applications that are in dire need of such assistance. Due to the lack of experience with body-worn robotics, the development of such systems has been shaped by trial and error. The lack of legacy products results in longer development times. In this paper, a process to generate a framework is presented to display the required research to enable future exoskeleton designers. Owing to their proximity to the user's body, exoskeletons are highly complex systems that need sophisticated subsystems, such as kinematic, control, interaction design, or actuators, to be accepted by users. Due to the wide variety of fields and high user demands, a synchronized multidisciplinary effort is necessary. To achieve this, a process to develop a modular framework for exoskeleton design is proposed. It focuses on user- and use-case-centered solutions for matching kinematics, actuation, and control. To ensure the usefulness of the framework, an evaluation of the incorporated solutions is required.

Effects of stance control via hidden Markov model-based gait phase detection on healthy users of an active hip-knee exoskeleton

Introduction: In the past years, robotic lower-limb exoskeletons have become a powerful tool to help clinicians improve the rehabilitation process of patients who have suffered from neurological disorders, such as stroke, by applying intensive and repetitive training. However, active subject participation is considered to be an important feature to promote neuroplasticity during gait training. To this end, the present study presents the performance assessment of the AGoRA exoskeleton, a stance-controlled wearable device designed to assist overground walking by unilaterally actuating the knee and hip joints. Methods: The exoskeleton's control approach relies on an admittance controller, that varies the system impedance according to the gait phase detected through an adaptive method based on a hidden Markov model. This strategy seeks to comply with the assistance-as-needed rationale, i.e., an assistive device should only intervene when the patient is in need by applying Human-Robot interaction (HRI). As a proof of concept of such a control strategy, a pilot study comparing three experimental conditions (i.e., unassisted, transparent mode, and stance control mode) was carried out to evaluate the exoskeleton's short-term effects on the overground gait pattern of healthy subjects. Gait spatiotemporal parameters and lower-limb kinematics were captured using a 3D-motion analysis system Vicon during the walking trials. Results and Discussion: By having found only significant differences between the actuated conditions and the unassisted condition in terms of gait velocity (ρ = 0.048) and knee flexion (ρ ≤ 0.001), the performance of the AGoRA exoskeleton seems to be comparable to those identified in previous studies found in the literature. This outcome also suggests that future efforts should focus on the improvement of the fastening system in pursuit of kinematic compatibility and enhanced compliance.

Assistive Mobility Control of a Robotic Hip-Knee Exoskeleton for Gait Training

In this paper, we present an assistive mobility control for a robotic hip-knee exoskeleton intended for gait training. The robotic hip-knee exoskeleton is designed with an active flexion/extension and a passive abduction/adduction at each hip joint and an active flexion/extension at each knee joint to comply with the movement of lower limbs. While facilitating walking with the robotic exoskeleton, model-free linear extended state observer (LESO)-based controllers are proposed for gait control, in which the LESO is used to deal with each user's different lower limb parameters and unknown exerted torques. Walking and ascending experiments were conducted to evaluate the performance of the proposed methods, and the results are shown with respect to walking parameters. Moreover, a preliminary study for an extended application to the recovery of normal gaits that relieves the freezing of gait (FOG) in Parkinson's disease (PD) patients is also investigated in the paper.

The Impact of COVID on Lower-Limb Exoskeleton Robotic System Patents—A Review

In recent decades, the field of physical rehabilitation, with the help of robotic systems that aid the population of any age with locomotor difficulties, has been evolving rapidly. Several robotic exoskeleton systems of the lower limbs have been proposed in the patent literature and some are even commercially available. Given the above, we are asking ourselves at the end of the COVID-19 pandemic: how much has this pandemic affected both the publication of patents and the application of new ones? How has new patents’ publication volume or application in robotic exoskeleton systems changed? We hypothesize that this pandemic has caused a reduction in the volume of new applications and possibly publications. We compare pandemic analysis and the last decade’s analysis to answer these questions. In this study, we used a set of statistical tests to see if there were any statistically significant changes. Our results show that the pandemic had at least one effect on applying for new patents based on the information analyzed from the three databases examined.