Effects of Support and Synthetic Procedure for Sol-Immobilized Au Nanoparticles

Catalytic Performance of Calcium Titanate for Catalytic Decomposition of Waste Polypropylene to Carbon Nanotubes in a Single-Stage CVD Reactor

Calcium titanate mixed metal oxides with different contents were used as supports for NiMo catalyst prepared by the sol–gel method. The activities of these catalysts were tested in the catalytic decomposition of waste polypropylene (PP) for the synthesis of carbon nanotubes (CNTs) using a single-stage chemical vapor deposition technique. The physico-chemical properties of the catalysts and deposited carbon over the catalysts were checked by X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature-programmed reduction (TPR), N2 physisorption, transmission electron microscopy (TEM), Raman spectroscopy, and thermogravimetric analysis (TGA). The TEM and XRD results presented a high dispersion of the active metal species on the surface of the support materials. The result showed that increasing the support content led to an increased crystallite size of the catalysts and a resultant reduction in CNTs yield from 44% to 35%. NiMo-supported CaTiO3 catalyst displayed good catalytic activity and stability toward CNTs growth. Furthermore, the effect of calcination temperature on the morphology, yield, and quality of CNTs was also studied, and it was observed that thermal treatment up to 700 °C could produce well graphitized, high-quality, and high-yield CNTs from the waste PP.

Advances in catalytic routes for the production of carboxylic acids from biomass: a step forward for sustainable polymers

Polymers are ubiquitously present in our daily life because they can meet a wide range of needs and fields of applications. This success, based on an irresponsible linear consumption of plastics and the access to cheap oil, is creating serious environmental problems. Two lines of actions are needed to cope with them: to adopt a circular consumption of plastics and to produce renewable carbon-neutral monomers. This review analyses the recent advances in the chemocatalytic processes for producing biomass-derived carboxylic acids. These renewable carboxylic acids are involved in the synthesis of relevant general purpose and specialty polyesters and polyamides; some of them are currently derived from oil, while others can become surrogates of petrochemical polymers due to their excellent performance properties. Polyesters and polyamides are very suitable to be depolymerised to other valuable chemicals or to their constituent monomers, what facilitates the circular reutilisation of these monomers. Different types of carboxylic acids have been included in this review: monocarboxylic acids (like glycolic, lactic, hydroxypropanoic, methyl vinyl glycolic, methyl-4-methoxy-2-hydroxybutanoic, 2,5-dihydroxypent-3-enoic, 2,5,6-trihydroxyhex-3-enoic acids, diphenolic, acrylic and δ-amino levulinic acids), dicarboxylic acids (2,5-furandicarboxylic, maleic, succinic, adipic and terephthalic acids) and sugar acids (like gluconic and glucaric acids). The review evaluates the technology status and the advantages and drawbacks of each route in terms of feedstock, reaction pathways, catalysts and economic and environmental evaluation. The prospects and the new research that should be undertaken to overcome the main problems threatening their economic viability or the weaknesses that prevent their commercial implementation have also been underlined.

Oxidation of lignocellulosic platform molecules to value-added chemicals using heterogeneous catalytic technologies

This minireview gives an overview about heterogeneous catalytic technologies for the oxidation of key platform molecules (glucose, 5-hydroxymethylfurfural, furfural and levulinic acid) into valuable chemicals.

Towards the continuous production of Pt-based heterogeneous catalysts using microfluidic systems

The continuous production of Pt-based heterogeneous catalysts based on ultra-small (<2 nm) noble metal nanoparticles deposited on mesoporous ordered silica and their catalytic activity in VOC abatement are here reported. Microfluidic reactors can be used not only to enable the fast and controlled production of ultra-small Pt nanoparticles (NPs), but also alloyed NPs including PtPd, PtRu and PtRh can be formed in short residence times (between 60 s and 5 min). A novel continuous and homogeneous loading of these catalytic NPs on SBA-15 used as a mesoporous support is also here reported. This procedure eases the NP loading and minimizes washing post-treatments. A 12-fold decrease in the synthesis time was obtained when using this microfluidic reactor compared to the traditional batch production of Pt NPs. Microflow and batch type reactors yielded a Pt precursor conversion to generate Pt NPs with a 90% and 85% yield, respectively. Under the same conditions, the productivity of the microfluidic system (27 mg Pt NPs per h) was twice the one achieved in the conventional batch type reactor. The catalytic performance of the supported catalysts separately prepared by microfluidics and by conventional impregnation under the same conditions and with the same noble metal loading was also compared in the n-hexane abatement as a model of VOCs. Both catalysts were active in the VOC oxidation reaction but a 95% reduction in the catalyst synthesis time was obtained when using the catalysts produced in the microfluidic platform. For this reaction a long-term activity test was successfully carried out at 175 °C during 30 h on stream using the heterogeneous catalyst prepared by using the flow reactor.