UV-Cured Coatings Prepared with Sulfhydryl-Terminated Branched Polyurethane and Allyl-Terminated Hyperbranched Polycarbosilane

High Efficiency and Low Migration Hyperbranched Silicone Contain Macrophotoinitiators for UV-Cured Transparent Coatings

A kind of hyperbranched silicone containing macrophotoinitiators (HBSMIs) were synthesized from 2-hydroxy-2-methyl-1-phenyl propanone (HMPP) and the UV-curing behaviors of HBSMIs were investigated in UV-cured transparent polyurethane-acrylate (PUA) coatings. HBSMIs show higher UV-initiating efficiency than HMPP. The migration of HBSMIs from the UV-cured coatings can be as low as 1.7–6.0 wt%, which is obviously lower than the migration of HMPP. There is a remarkable improvement of the tensile strength of the UV-cured materials initiated by HBSMI in comparison to that of the materials prepared with the same PUA initiated by HMPP. Especially for the UV-cured materials prepared from PUA with 20 wt% 1,1,1-tris(hydroxymethyl)propane (TMP), the tensile strength and the strain at break increased from 6.81 MPa to 12.14 MPa and from 43.0% to 71.9%, respectively. The fraction of improvement for the tensile strength and the strain at break is as high as 78.9% and 67.2%, respectively. The coatings prepared with HBSMI also have better UV resistance ability than those coatings prepared with HMPP because they turn slightly yellow when they are aged by UV for about 15 min while the coating prepared with 4 wt% of HMPP will turn yellow only aged by UV for 2 min. These results suggest that preparation hyperbranched silicone containing macrophotoinitiators will be one of the good strategies to improve the curing efficiency of the UV-curing system, reduce the migration of UV initiator from cured material, improve the mechanical and UV resistance performance of UV-cured materials.

An Easy Fabrication Method to Prepare Inexpensive UV–Cured Transparent Silicone Modified Polyacrylate Coatings with Good Adhesion and UV Resistance

UV–curable polyacrylate is widely used in free–radical type UV–cure coating systems, the disadvantages of which including poor thermal stability and UV resistance can be overcome through chemical modification by silicone. However, it is a remarkable fact that the strategies for fabrication UV–cured silicone modified polyacrylates are somewhat complicated and the price of the products may be much expensive than pure UV–cured polyacrylates. In this work, an easy fabrication method to prepare inexpensive UV–cured transparent silicone modified polyacrylate coatings with good adhesion and UV resistance performance was developed from copolymers of acylates and thiol silicone resin by UV initiated thiol–ene click reaction without UV initiator. The striking results with a high application value should be emphasized that when the amount of thiol silicone resin is only one wt.% of the copolymer of acrylates, the UV–cured coatings obtained exhibit fairly good performance. These coatings prepared exhibit transparency higher than 96% (800 nm), adhesion property to glass slides can reach grade 0, pencil hardness can reach 6H, water absorption is less than 0.16%. In particular, it is observed obviously that the silicone modified polyacrylate coatings exhibit better UV resistance performance than the coating prepared with only copolymers of acrylates initiated by UV initiator 1173. It is proved that it is actually an easy fabrication method to prepare inexpensive UV–cured transparent silicone modified polyacrylate coatings with high performance by UV initiated thiol–ene click reaction of copolymers of acylates and thiol silicone resin.

Fabrication of Transparent UV-Cured Coatings with Allyl-Terminated Hyperbranched Polycarbosilanes and Thiol Silicone Resins

To improve thermal stability and hardness of UV-cured materials, a series of UV-cured solvent-free coatings were prepared from allyl-terminated hyperbranched polycarbosilanes and thiol silicone resins. The silicone coatings prepared have pencil hardness of 4-9 H, water absorption no more than 0.04 wt %, and transmittance higher than 94%. The temperature for the coatings' starting thermal decomposition is higher than 236 °C; especially, that of the coating prepared with G1 is as high as 371.1 °C. The UV-cured coatings in this work exhibit much higher pencil hardness than and superior thermal stability to those reported previously.