Microstructural Characterization and Corrosion-Resistance Behavior of Dual-Phase Steels Compared to Conventional Rebar

Tailoring the mechanical strength and corrosion resistance of aluminum matrix composites through biochar reinforcement at varied weight percentages

This study introduces an innovative approach to fabricate aluminum matrix composites strengthened with biochar, derived from renewable biomass sources. A systematic investigation of varying biochar weight percentages (0, 2.5, 5, 7.5, and 10 wt%) reveals substantial improvements in mechanical properties and corrosion resistance. Mechanical assessments, including compressive strength and hardness, demonstrate a significant enhancement in mechanical strength with biochar incorporation. In this study, it was discovered that the composite with 7.5 wt% biochar exhibits an optimal balance, displaying an 8.83% increase in compressive strength and a 15.15% rise in hardness compared to the base aluminum matrix. The study further evaluates corrosion behavior through electrochemical analyses and immersion tests in 3.5% NaCl corrosive environments, highlighting the superior corrosion resistance of biochar-reinforced composites. Corrosion rates decrease by 73% in the composite with 10 wt% biochar for the 24 h immersion time, affirming its protective barrier against corrosive agents. This research provides quantitative insights into tailoring mechanical and corrosion properties in aluminum matrix composites through biochar reinforcement, offering a promising avenue for sustainable material development. The resulting materials exhibit not only an 8.83% increase in mechanical strength but also a 73% reduction in corrosion rates, offering valuable uses in industries that need strong, eco-friendly solutions.

Synergistic Effect of Nanoparticles: Enhanced Mechanical and Corrosion Protection Properties of Epoxy Coatings Incorporated with SiO2 and ZrO2

This research paper presents the fabrication of epoxy coatings along with the hybrid combination of SiO₂ and ZrO₂. The epoxy resin is incorporated with SiO₂ as the primary pigment and ZrO₂ as the synergist pigment. The study delves into the adhesion, barrier, and anti-corrosion properties of these coatings, enriched with silica and zirconium nanoparticles, and investigates their impact on the final properties of the epoxy coating. The epoxy resin, a Diglycidyl ether bisphenol-A (DGEBA) type, is cured with a polyamidoamine adduct-based curing agent. To evaluate the protective performance of silica SiO₂ and zirconia ZrO₂ nanoparticles in epoxy coatings, the coated samples were tested in a 3.5% NaCl solution. The experimental results clearly demonstrate a remarkable improvement in the ultimate tensile strength (UTS), yield strength (YS), and Elastic Modulus. In comparison to using SiO₂ separately, the incorporation of both ZrO₂ and SiO₂ resulted in a substantial increase of 43.5% in UTS, 74.2% in YS, and 8.2% in Elastic Modulus. The corrosion test results revealed that the combination of DGEBA, SiO₂, and ZrO₂ significantly enhanced the anti-corrosion efficiency of the organic coatings. Both these pigments exhibited superior anti-corrosion effects and mechanical properties compared to conventional epoxy coatings, leading to a substantial increase in the anti-corrosion efficiency of the developed coating. This research focuses the potential of SiO₂ and ZrO₂ in hybrid combination for applications, where mechanical, corrosion and higher adhesion to the substrates are of prime importance.

Investigation on mechanical properties and corrosion resistance of Ti-modified AA5083 aluminum alloy for aerospace and automotive applications

Casting of aluminum with different concentration of alloying elements such as Mg, Mn (similar to that in AA5083) with additional percentages of 0.1, 0.2 and 0.3% Ti, are carried out using graphite crucible. The as-cast microstructure is modified by hot rolling to a thickness of ~ 2 mm. Mechanical and metallurgical and characterization of heat-treated thin sheets are carried out using tensile testing, hardness measurement, metallography, image analysis and optical microscope. By increasing the Ti content, the results show grain refinement and increase in the formation of Al3Ti which reflected positively on the mechanical properties. Specifically, Ultimate tensile strength is increased from 260 MPa (0 wt% Ti) to 345 MPa (0.3 wt% Ti) when using water quenching, 32.6% improvement for air cooling, and 23.3% for furnace cooling. Electrochemical corrosion behavior of heat-treated water quenched, air cooled and furnace cooled samples were tested in 3.5% NaCl solution. The results show that the heat-treated alloys have very good resistance against corrosion, while by increasing the Ti content, the corrosion rate increases due to the grain refinement phenomena.

Electrochemical Behavior of Inductively Sintered Al/TiO2 Nanocomposites Reinforced by Electrospun Ceramic Nanofibers

This study is focuses on the investigation of the effect of using TiO₂ short nanofibers as a reinforcement of an Al matrix on the corrosion characteristics of the produced nanocomposites. The TiO₂ ceramic nanofibers used were synthesized via electrospinning by sol-gel process, then calcinated at a high temperature to evaporate the residual polymers. The fabricated nanocomposites contain 0, 1, 3 and 5 wt.% of synthesized ceramic nanofibers (TiO₂). Powder mixtures were mixed for 1 h via high-energy ball milling in a vacuum atmosphere before being inductively sintered through a high-frequency induction furnace at 560 °C for 6 min. The microstructure of the fabricated samples was studied by optical microscope and field emission scanning electron microscope (FESEM) before and after corrosion studies. Corrosion behavior of the sintered samples was evaluated by both electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization techniques (PPT) in 3.5% NaCl solution for one hour and 24-h immersion times. The results show that even though the percentage of ceramic nanofibers added negatively control corrosion resistance, it is still possible to increase resistance against corrosion for the fabricated nanocomposite by more than 75% in the longer exposure time periods.

Controlling Atmospheric Corrosion of Weathering Steel Using Anodic Polarization Protection Technique

The atmospheric corrosion of weathering steels varies as a function of geographic zone, season, and other environmental variables related to that region which the experiments have been done. Meanwhile, rusting is a continuous process, and it is the main corrosion product of atmospheric corrosion. The current study investigates the effects of rust on weathering steel in the localized region of Digha, a sea resort of West Bengal, India. The investigations have been performed by purposely accelerating the rusting of weathering steel in a laboratory within one week in order to simulate approximately 18 months of actual rusting that can be achieved at field exposure. Anodic polarization of weathering steel comparable to potentiostatic passivation is obtained by shorting weathering steel with nobler metals, such as copper or graphite. The effect of rust formation on corrosion resistance after being immersed in 0.01 M KCl solutions for polished and unpolished samples has been investigated using electrochemical techniques, such as potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The rusted surfaces’ morphology and composition were characterized using field emission scanning electron microscope (FE-SEM) and energy dispersive X-ray analysis (EDX). Based on the obtained results, it is concluded that the progressive rusting of weathering steel leads to a decrease in corrosion rate.

Mitigating Corrosion Effects of Ti-48Al-2Cr-2Nb Alloy Fabricated via Electron Beam Melting (EBM) Technique by Regulating the Immersion Conditions

The corrosion behavior of newly fabricated γ-TiAl alloy was studied using electrochemical impedance spectroscopy (EIS) and cyclic potentiodynamic polarization (CPP) techniques. The γ-TiAl alloy was produced from powder with compositions of Ti-48Al-2Cr-2Nb processed using electron beam melting (EBM) technique. The corrosion behavior of the bulk alloy was investigated in 1 M HCl solution for different immersion times and temperatures. The experimental results suggest that the fabricated alloy exhibits good resistance to corrosion in acid solution at room temperature. The results also indicate that with an increase in immersion time and solution temperature, the corrosion potential (Ecorr) shifts to a higher positive value, resulting in an increase in corrosion current (jcorr) and consequently a decrease in the corrosion resistance (Rp) of the alloy.