A Study on Precise Positioning for an Electric Vehicle Wireless Power Transfer System Using a Ferrite Antenna

On Power Line Positioning Systems

Power line infrastructure is available almost everywhere. Positioning systems aim to estimate where a device or target is. Consequently, there may be an opportunity to use power lines for positioning purposes. This survey article reports the different efforts, working principles, and possibilities for implementing positioning systems relying on power line infrastructure for power line positioning systems (PLPS). Since Power Line Communication (PLC) systems of different characteristics have been deployed to provide communication services using the existing mains, we also address how PLC systems may be employed to build positioning systems. Although some efforts exist, PLPS are still prospective and thus open to research and development, and we try to indicate the possible directions and potential applications for PLPS.

Short Range Electromagnetic Interface Using 0.35 um CMOS Blocks for Temperature Monitoring in Isolated Areas

•

Simple and low-cost system with high immunity against issues of standard optical transmission (vapor, fog).

•

Operation without significant path loss of the energy on very short distances for minimization of interferences with other services.

•

Bandwidth fitting low-frequency and biomedical applications (from sub-Hz to hundreds of Hz or slowly varying DC voltages).

•

Complete implementation of active parts in a form of Application Specific Integrated Circuit for low power consumption and.

•

Typical application example in monitoring of environmental features (temperature measurement).

Introduction

Infra-red (IR) and visible light (VL) based systems developed for transmission of information about physical quantities (e.g. humidity, temperature) out from closed areas, cannot be effectively employed in case of specific conditions in a targeted environment (because of fog or vapor for example).

Objectives

In this work, we introduce a concept of wireless short-range transmitter and receiver to sense physical quantities, for instance temperature, with slow variation. The proposed concept is able to transmit analog-based information from isolated environments (e.g. aquariums or environments for plant growing) with high immunity against vapor and fog that limits standard optical (laser, IR band) methods of communication.

Methods

In this work, a new concept of short range radiofrequency (RF) communication device consisting of transmitting and receiving parts build from active devices fabricated in 0.35 μm I3T25 3.3 V CMOS process and ferrite antennas is selected. RF part uses medium-wave propagation within 10 mm distance at frequency 700 kHz. Such an approach offers minimal path loss of the radiated energy of a signal and low-gain amplification required for restoration of similar levels as available at the transmitting side.

Results

The processing of base-band signals of simple (sine wave) and complex (electrocardiogram) character was verified experimentally through the system. Application example of temperature monitoring in a closed environment, based on a temperature sensor (thermistor), verifies operationability in temperature range from 10 °C up to 50 °C.

Conclusion

Compared to state-of-the-art solution, the presented concept has several advantages, for instance: less complexity; using of simpler type of modulation and demodulation; lower power consumption and significantly reduced issues caused by an environment with special transmission conditions (e.g. fog and vapor). The obtained results are in good agreement with expectations. Among others, the presented system brings beneficial performances for similar applications targeting on monitoring of low-frequency or slowly varying signals.

Stability Improvement of Dynamic EV Wireless Charging System with Receiver-Side Control Considering Coupling Disturbance

Receiver-side control has been a reliable practice for regulating the transferred energy to the batteries in the electric vehicle (EV) wireless power transfer (WPT) systems. Nonetheless, the unpredictable fluctuation of the mutual inductance in dynamic wireless charging brings extreme instability to the charging process. This overshoot that appears in instant vibrations may largely increase the voltage/current stress of the system, and even cause catastrophic failure in the battery load. In addition, the speed of the vehicles may lead to untraceable steady-state operation. However, existing solutions to the above two issues suffer from either long communication time delay or significantly compromised output regulation. In this paper, the slow dynamics and the overshoot issues of the WPT system are elaborated in theory, and the small-signal model mainly considering mutual inductance disturbance is established. A simple feedforward control is proposed for overshoot damping and fast system dynamics. Experimental results validate that the overshoot can be reduced by 13% and the settling time is improved by 50% in vehicle braking or acceleration. In constant speed driving, the battery charging ripple is decreased by 12% and ensures better system stability.

A Novel Metal Foreign Object Detection for Wireless High-Power Transfer Using a Two-Layer Balanced Coil Array with a Serial-Resonance Maxwell Bridge

In a wireless high-power transfer system with a distance of several tens of centimeters apart between the transmitter and receiver coils, one of the most challenging issues is to detect metallic foreign objects between the transmitter and receiver coils. The metallic foreign objects must be detected and removed since these reduce the transmission efficiency and cause heat generation of the transmitter and receiver. This paper presents two-layer symmetric balanced coil array so that if there are metallic foreign objects, it can be detected through the change of the inductance of the balanced coils. Since the balanced coil is composed of coils that are in a symmetrical relationship in position, there is no need for a reference coil, and interference between coils is reduced by dividing the coil into two layers. In addition, a novel serial-resonance Maxwell bridge circuit to improve the inductance change detection performance is presented in this paper. The proposed metallic foreign object detection system is implemented using two-layer balanced coil array with a serial-resonance Maxwell bridge and the experimental results show that voltage changes of hundreds of mV to several V occur when a metallic foreign object is inserted, so that even small metals such as clips can be detected.