Physicochemical, Rheological, In-Vitro Digestibility, and Emulsifying Properties of Starch Extracted from Pineapple Stem Agricultural Waste

Physical properties and in-vitro gastrointestinal digestion of oil-in-water emulsions stabilized by single- and dual-modified cassava starches with cross-linking and octenylsuccinylation

The different modified cassava starches (MCS) obtained by either single or dual modifications with cross-linking (CL) and octenylsuccinylation (OS), including 2%CL, 3%OS, 2%CL-3%OS, and 3%OS-2%CL, were used to stabilize soybean oil-in-water emulsions (oil content 10% (w/w)) at a concentration of 4.5% (w/w) compared to native cassava starch (NCS) and their physical properties and in-vitro gastrointestinal digestion were investigated. The emulsions stabilized with NCS and 2%CL-MCS had larger oil droplet sizes, higher viscosity, and lower negative charge than the emulsions stabilized by single- or dual-MCS with 3%OS. All MCS-stabilized emulsions showed a higher emulsion stability against creaming than the NCS-stabilized emulsion. Under a simulated gastrointestinal tract, all 3%OS-MCS promoted droplet flocculation, while the less ionic NCS and the 2%CL-MCS showed a decrease in droplet size after passing through the mouth and stomach stages. The lipid digestion rate of emulsions stabilized with different MCS and NCS followed the following order: 3%OS >2%CL-3%OS > 3%OS-2%CL > 2%CL > NCS. The NCS- and 2%CL-stabilized emulsions had a lower lipid digestion rate, possibly due to the larger droplet sizes and higher viscosity of the initial emulsions, which delays access of lipase enzymes to lipid droplet surfaces, compared to all 3%OS-MCS-stabilized emulsions.

Impact of Oil Addition on Physicochemical Properties and In Vitro Digestibility of Extruded Pineapple Stem Starch

The effects of palm oil (PO) and coconut oil (CO) additions on the physicochemical properties and in vitro starch digestibility of extruded pineapple stem starch (PSS) were studied. The native PSS was adjusted to 15% moisture and blended with PO or CO in amounts of 5 and 10% (w/w of starch), while the control sample without added oil was adjusted to 25% moisture before being extruded with a twin-screw extruder at a maximum barrel temperature of 140 °C. Due to the lubricating effect, the added oils reduced the expansion ratio of the extrudates, which led to an increase in cell wall thickness, bulk density, hardness, and water adsorption index, but to a reduction in the water solubility index, especially with 10% oils. PO had a greater impact on the physicochemical changes in the extrudates than CO. Surprisingly, no amylose-lipid complex was observed in the extrudates with added oil, as shown by XRD, DSC, and FTIR results. The phenolic compounds contained in PSS remained in all extrudates, which could affect the formation of the amylose-lipid complex during extrusion. The addition of 5% oil had no effect on the digestibility of the starch compared to the control extrudates, while the 10% oils, both PO and CO, reduced the rapidly digestible starch content but significantly increased the resistant starch content of the extruded PSS.

Development of Biodegradable Thermosetting Plastic Using Dialdehyde Pineapple Stem Starch

Starch extracted from pineapple stem waste underwent an environmentally friendly modification process characterized by low-energy consumption. This process resulted in the creation of dialdehyde pineapple stem starch featuring varying aldehyde contents ranging from 10% to 90%. Leveraging these dialdehyde starches, thermosetting plastics were meticulously developed by incorporating glycerol as a plasticizer. Concurrently, unmodified pineapple stem starch was employed as a control to produce thermoplastic material under identical conditions. The objective of streamlining the processing steps was pursued by adopting a direct hot compression molding technique. This enabled the transformation of starch powders into plastic sheets without the need for water-based gelatinization. Consequently, the dialdehyde starch-based thermosetting plastics exhibited exceptional mechanical properties, boasting a modulus within the range of 1862 MPa to 2000 MPa and a strength of 15 MPa to 42 MPa. Notably, their stretchability remained relatively modest, spanning from 0.8% to 2.4%. Comparatively, these properties significantly outperformed the thermoplastic counterpart derived from unmodified starch. Tailoring the mechanical performance of the thermosetting plastics was achieved by manipulating the glycerol content, ranging from 30% to 50%. Phase morphologies of the thermoset starch unveiled a uniformly distributed microstructure without any observable starch particles. This stood in contrast to the heterogeneous structure exhibited by the thermoplastic derived from unmodified starch. X-ray diffraction patterns indicated the absence of a crystalline structure within the thermosets, likely attributed to the establishment of a crosslinked structure. The resultant network formation in the thermosets directly correlated with enhanced water resistance. Remarkably, the thermosetting starch originating from pineapple stem starch demonstrated continued biodegradability following a soil burial test, albeit at a notably slower rate when compared to its thermoplastic counterpart. These findings hold the potential to pave the way for the utilization of starch-based products, thereby replacing non-biodegradable petroleum-based materials and contributing to the creation of more enduring and sustainable commodities.