Spectral inverse quantum (Spectral-IQ) method for modeling mesoporous systems: application on silica films by FTIR

High sensitivity, low-cost, and disposability: A novel screen-printed electrode developed for direct electrochemical detection of the antibiotic ceftriaxone

This study describes the development of a novel disposable and low-cost electrochemical platform for detecting the antibiotic ceftriaxone. The screen-printed electrode has been modified with a novel hybrid nanostructure containing silicon oxide (SiO2), zirconium oxide (ZrO2), and nitrogen-doped carbon quantum dots (Cdot-N). Different techniques like Fourier-transform infrared spectroscopy, Raman spectroscopy, and transmission electron microscopy characterized the hybrid nanostructure used in the sensor surface modifier material. The hybrid nanostructure showed an excellent synergistic effect that contributed to the oxidation reaction of ceftriaxone. The screen-printed electrode modified with SiO2/ZrO2/Cdot-N nanostructure presented high sensitivity with a detection limit of 0.2 nmol L-1 in the linear range of 0.0078-40.02 μmol L-1. The measurements have been performed by square wave voltammetry technique. Studies on real samples of synthetic urine, urine, and tap water showed 95%-105% recovery without applying any sample pretreatment. The sensor demonstrated excellent selectivity in the antibiotic ceftriaxone determination in the presence of possible interferences cationic, Na+, K+, Ca2+, Mg2+, Cu2+, Pb2+, Mn2+, Zn2+, Co2+, and biological, glucose, caffeine, uric acid, and ascorbic acid. The developed sensor becomes a selective, sensitive, and applicable tool in determining the antibiotic ceftriaxone.

Low-Cost Flexible Glass-Based pH Sensor via Cold Atmospheric Plasma Deposition

Many commercially available pH sensors are fabricated with a glass membrane as the sensing component because of several advantages of glass-based electrodes such as versatility, high accuracy, and excellent stability in various conditions. However, because of their bulkiness and poor mechanical properties, conventional glass-based sensors are not ideal for wearable or flexible applications. Here, we report for the first time the fabrication of a flexible glass-based pH sensor suitable for biomedical and environmental applications where flexibility and stability of the sensor are critical for long-term and real-time monitoring. The sensor was fabricated via a simple and facile approach using the cold atmospheric plasma technique in which a pH sensitive silica coating was deposited from a siloxane precursor onto a carbon electrode. In order to increase the sensitivity and stability of the sensor, we employed a postprocessing step which involves annealing of the silica coated electrode at elevated temperatures. This process was optimized to ensure that the crucial properties such as porosity and hydration functionality were balanced to obtain the best and most reliable sensitivity of the sensor. Our sensitivity test results indicated that these sensors exhibit excellent and stable sensitivity with a slope of about 48 mV/pH (r² = 0.998) and selectivity across a pH range of 4 to 10 in the presence of various cations. The optimized sensor has shown stable sensitivity for a long period of time (30 h of immersion) and in different bending conditions. We demonstrate in this investigation that this flexible cost-effective pH sensor can withstand the sterilization process resulting from ultraviolet radiation and shows repeatable sensitivity with less than ±5 mV potential drift from the sensitivity values of the standard optimized sensor.

Nanoceria provides antioxidant and osteogenic properties to mesoporous silica nanoparticles for osteoporosis treatment

Osteoporosis, a chronic metabolic bone disease, is the most common cause of fractures. Drugs for treating osteoporosis generally inhibit osteoclast (OC) activity, but are rarely aimed at encouraging new bone growth and often cause severe systemic side effects. Reactive oxygen species (ROS) are one of the key triggers of osteoporosis, by inducing osteoblast (OB) and osteocyte apoptosis and promoting osteoclastogenesis. Here we tested the capability of the ROS-scavenger nanoceria encapsulated within mesoporous silica nanoparticles (Ce@MSNs) to treat osteoporosis using a pre-osteoblast MC3T3-E1 cell monoculture in stressed and normal conditions. Ce@MSNs (diameter of 80 ± 10 nm) were synthesised following a scalable two-step process involving sol-gel and wet impregnation methods. The Ce@MSNs at concentration of 100 μg mL^-1 induced a significant reduction in oxidative stress produced by t-butyl hydroperoxide and did not alter cell viability significantly. Confocal microscopy showed that MSNs and Ce@MsNs were internalised into the cytoplasm of the pre-osteoblasts after 24 h but were not in the nucleus, avoiding any DNA and RNA modifications. Ce@MSNs provoked mineralisation of the pre-osteoablasts without osteogenic supplements, which did not occur when the cells were exposed to MSN without nanoceria. In a co-culture system of MC3T3-E1 and RAW264.7 macrophages, the Ce@MSNs exhibited antioxidant capability and stimulated cell proliferation and osteogenic responses without adding osteogenic supplements to the culture. The work brings forward an effective platform based for facile synthesis of Ce@MSNs to interact with both OBs and OCs for treatment of osteoporosis.

Yolk-void-shell Si-C nano-particles with tunable void size for high-performance anode of lithium ion batteries

Silicon is a promising anode for new-generation lithium ion batteries due to high theoretical lithium storage capacity (4200 mAh g^-1). However, the low conductivity and large volumetric expansion hamper the commercialization of the silicon anode. In this case, we present a yolk-void-shell Si-C anode (denoted as Si@Void@C), which is synthesized through nano-Si oxidation, surface carbonization and etching of SiO _x . The void can be fabricated only by the self-generation and etching of SiO _x layer on the Si surface, without the help of template materials. Moreover, the void size can be adjusted only by means of the annealing temperature, which can be easily and precisely operated. The Si@Void@C/rGO with void size of 5 nm offers a discharge capacity of 1294 mAh g^-1 after 100 cycles at a current density of 500 mA g^-1. These enhanced performances can be ascribed to an appropriate size (5 nm) of void space which sufficiently accommodates the silicon volume expansion and stabilizes the carbon shell. At the same time, the voids effectively inhibit the growth of the solid electrolyte interface layer by depressing the decomposition of the electrolyte on the surface of Si in Si@Void@C/rGO. Furthermore, interfaces between Si@Void@C particles and rGO sheets construct bridges for electrons' conduction. In general, the present work provides a viable strategy for synthesizing silicon-carbon anode materials with long life.

An experimental and theoretical approach on stability towards hydrolysis of triethyl phosphate and its effects on the microstructure of sol-gel-derived bioactive silicate glass

The sol-gel method is versatile and one of the well-established synthetic approaches for preparing bioactive glass with improved microstructure. In a successful approach, alkoxide precursors undergo rapid hydrolysis, followed by immediate condensation leading to the formation of three-dimensional gels. On the other hand, a slow kinetics rate for hydrolysis of one or more alkoxide precursors generates a mismatch in the progression of the consecutive reactions of the sol-gel process, which makes it difficult to form homogeneous multicomponent glass products. The amorphous phase separation (APS) into the gel is thermodynamically unstable and tends to transform into a crystalline form during the calcination step of xerogel. In the present study, we report a combined experimental and theoretical method to investigate the stability towards hydrolysis of triethyl phosphate (TEP) and its effects on the mechanism leading to phase separation in 58S bioactive glass obtained via sol-gel route. A multitechnical approach for the experimental characterization combined with calculations of functional density theory (DFT) suggest that TEP should not undergo hydrolysis by water under acidic conditions during the formation of the sol or even in the gel phase. The activation energy barrier (ΔG^‡) showed a height of about 20 kcal·mol^-1 for the three stages of hydrolysis and the reaction rates calculated for each stage of TEP hydrolysis were k_FHR = 7.0 × 10^-3s^-1, k_SHR = 6.8 × 10^-3s^-1 and k_THR = 3.5 × 10^-3s^-1. These results show that TEP remains in the non-hydrolyzed form segregated within the xerogel matrix until its thermal decomposition in the calcination step, when P species preferentially associate with calcium ions (labile species) and other phosphate groups present nearby, forming crystalline domains of calcium pyrophosphates permeated by the silica-rich glass matrix. Together, our data expand the knowledge about the synthesis by the sol-gel method of bioactive glass and establishes a mechanism that explains the role played by the precursor source of phosphorus (TEP) in the phase separation, an event commonly observed for these biomaterials.

DyxMnFe2-xO4 nanoparticles decorated over mesoporous silica for environmental remediation applications

An efficient, environment-friendly and economical catalyst to control contaminants of environment is an enduring interest in recent years. In this study, a new composite, Dy_xMnFe_2-xO₄nanoparticles decorated over mesoporous silica was synthesized and utilized for removal of organic pollutant. Highly crystalline nature of Dy_xMnFe_2-xO₄ nanoparticles and amorphous nature of material was confirmed by XRD (X-ray diffraction) technique. Infrared spectra of fabricated material before and after adsorption of dye molecules evidenced the successful adsorption of dye molecules by fabricated adsorbent. From field emission scanning electron microscopic (FESEM) images of Dy³⁺ substituted MnFe₂O₄ composite with mesoporous silica, it was clearly observed that ferrite particles of size 20-30 nm were decorated on the surface of mesoporous silica particles and distributed well over spherical silica balls homogeneously. Its magnificent mesoporous nature was revealed from BET (nitrogen adsorption-desorption measurements) analysis. Surface area, pore volume and average pore size was found 387.95 m²/g, 0.390 cm³/g and 4.02 nm respectively. Tri-modal pore size distribution showed its effective utilization in adsorption. The abundant (SiOH) hydroxyl groups of mesoporous silica, the broad diffraction hump of silica depicted its superior loading capacity of target molecular specie inside its porous network. From band gap analysis, a red shift of 2.43 eV exhibited semiconductor photocatalysis of Dy_xMnFe_2-xO₄ nanoparticles. Degradation efficiency of bare MnFe₂O₄, Dy_xMnFe_2-xO₄ and mesoporous silica-based composite was tested using crystal violet dye. Its explored adsorption-photocatalysis synergy, degradation mechanism, kinetic investigation, easily recovery and remarkable recycling ability suggested that the new fabricated composite is best for environmental remediation.

Critical Role of the Molecular Interface in Double-Layered Pebax-1657/PDMS Nanomembranes for Highly Efficient CO2/N2 Gas Separation

In this work, we deposited a CO₂-selective block copolymer, Pebax-1657, as a selective layer with a thickness of 2-20 nm on the oxygen plasma-activated surface of poly(dimethylsiloxane) (PDMS) used as a gutter layer (thickness ∼400 nm). This double-layered structure was subsequently transferred onto the polyacrylonitrile (PAN) microporous support and studied for CO₂/N₂ separation. The effect of interfacial molecular arrangements between the selective and gutter layers on CO₂ permeance and selectivity has been investigated. We have revealed that the gas permeance and selectivity do not follow the conventional theoretical predictions for the multilayer membrane (resistance in series transport model); specifically, more selective CO₂/N₂ separation membranes were achieved with ultrathin selective layers. Detailed characterization of the chemical structure of the outermost membrane surface suggests that nanoscale blending of the ultrathin Pebax-1657 layer with O₂ plasma-activated PDMS chains on the surface takes place. This nanoblending at the interface between the selective and gutter layers played a critical role in enhancing the CO₂/N₂ selectivity. CO₂ permeances in the developed thin-film composite membranes (TFCM) were between 1200 and 3500 gas permeance units (GPU) and the respective CO₂/N₂ selectivities were between 72 and 23, providing the gas separation performance suitable for CO₂ capture in postcombustion processes. This interpenetrating polymer interface enhanced the overall selectivity of the membrane significantly, exceeding the separation ability of the pristine Pebax-1657 polymer.

A Direct Silanization Protocol for Dialdehyde Cellulose

Cellulose derivatives have many potential applications in the field of biomaterials and composites, in addition to several ways of modification leading to them. Silanization in aqueous media is one of the most promising routes to create multipurpose and organic-inorganic hybrid materials. Silanization has been widely used for cellulosic and nano-structured celluloses, but was a problem so far if to be applied to the common cellulose derivative "dialdehyde cellulose" (DAC), i.e., highly periodate-oxidized celluloses. In this work, a straightforward silanization protocol for dialdehyde cellulose is proposed, which can be readily modified with (3-aminopropyl)triethoxysilane. After thermal treatment and freeze-drying, the resulting product showed condensation and cross-linking, which was studied with infrared spectroscopy and 13C and 29Si solid-state nuclear magnetic resonance (NMR) spectroscopy. The cross-linking involves both links of the hydroxyl group of the oxidized cellulose with the silanol groups (Si-O-C) and imine-type bonds between the amino group and keto functions of the DAC (-HC=N-). The modification was achieved in aqueous medium under mild reaction conditions. Different treatments cause different levels of hydrolysis of the organosilane compound, which resulted in diverse condensed silica networks in the modified dialdehyde cellulose structure.

DNA Origami as Emerging Technology for the Engineering of Fluorescent and Plasmonic-Based Biosensors

DNA nanotechnology is a powerful and promising tool for the development of nanoscale devices for numerous and diverse applications. One of the greatest potential fields of application for DNA nanotechnology is in biomedicine, in particular biosensing. Thanks to the control over their size, shape, and fabrication, DNA origami represents a unique opportunity to assemble dynamic and complex devices with precise and predictable structural characteristics. Combined with the addressability and flexibility of the chemistry for DNA functionalization, DNA origami allows the precise design of sensors capable of detecting a large range of different targets, encompassing RNA, DNA, proteins, small molecules, or changes in physico-chemical parameters, that could serve as diagnostic tools. Here, we review some recent, salient developments in DNA origami-based sensors centered on optical detection methods (readout) with a special emphasis on the sensitivity, the selectivity, and response time. We also discuss challenges that still need to be addressed before this approach can be translated into robust diagnostic devices for bio-medical applications.

Reaction-Based, Fluorescent Film Deposition from Dopamine and a Diamine-Tethered, Bis-Resorcinol Coupler

The reaction-based deposition on various surfaces of an all-organic fluorescent coating is reported here, involving autoxidation of 2 mM dopamine in carbonate buffer at pH 9.0, in the presence of a 1 mM diamine–resorcinol coupler (Bis–Res) prepared from 2,4-dihydroxybenzaldehyde and hexamethylenediamine (HMDA). Spectral analysis of the films coupled with an LC-MS investigation of the yellow fluorescent mixture was compatible with the formation and deposition of HMDA-linked methanobenzofuroazocinone fluorophores. Both the emission properties and hydrophobicity of the film were abated in a reversible manner following exposure to acid vapors. These results provide an entry to efficient and practical fluorescent coating methodologies based on in situ generation and the deposition of wet adhesive, as well as fluorescent materials combining a strongly emitting fluorophore with the film-forming properties of long chain diamines.

Hollow nanostructure of sea-sponge-C/SiC@SiC/C for stable Li+-storage capability

For the purpose of stable performance in energy storage systems, a new hollow nanostructure of sea-sponge-C/SiC@SiC/C (SCS/SiC@SiC/C) has been successfully fabricated by the SCS/SiC nanospheres coated with SiC/C shells through an in situ reduction process. Based on SCSs and the carbon shells, the stable hollow structures of SCS/SiC@SiC/C can contain large proportion of active SiC layers, which are adhered to both SCSs and the inner surfaces of carbon shells. Such nanostructured anode enables an excellent cycling stability with a capacity of 612 mAh/g at a current density of 0.5 A/g after 1,800 cycles, achieving an excellent stable Li⁺-storage capability.

The Multifaceted Role of Methylaluminoxane in Metallocene-Based Olefin Polymerization Catalysis

In single-site olefin polymerization catalysis, a large excess of cocatalyst is often required for the generation of highly active catalysts, but the reason for this is unclear. In this work, fundamental insight into the multifaceted role of cocatalyst methylaluminoxane (MAO) in the activation, deactivation, and stabilization of group 4 metallocenes in the immobilized single-site olefin polymerization catalyst was gained. Employing probe molecule FT-IR spectroscopy, it was found that weak Lewis acid sites, inherent to the silica-supported MAO cocatalyst, are the main responsible species for the genesis of active metallocenes for olefin polymerization. These weak Lewis acid sites are the origin of AlMe₂⁺ groups. Deactivation of metallocenes is caused by the presence of silanol groups on the silica support. Interaction of the catalyst precursor with these silanol groups leads to the irreversible formation of inactive metallocenes. Importantly, a high concentration of MAO (14 wt% Al) on the silica support is necessary to keep the metallocenes immobilized, hence preventing metallocene leaching and consequent reactor fouling. Increasing the loading of the MAO cocatalyst leads to larger amounts of AlMe₂⁺, fewer silanol groups, and less metallocene leaching, which all result in higher olefin polymerization activity.

Preparation of Eu3+ ions activated Ca2La8(SiO4)6O2 oxyapatite nanophosphors through two-step surfactant-free method and their optical and electrical properties

Eu³⁺ ions activated Ca₂La₈(SiO₄)₆O₂ (CLSO):Eu³⁺ nanophosphor samples were synthesized by a mixed solvothermal and hydrothermal method. The samples were carefully studied using various characterization techniques. The XRD patterns of CLSO:Eu³⁺ and CLSO confirmed that the samples were crystallized in hexagonal phase with a space group of P6₃/m (176). The morphology of the nanoparticles was studied by varying the reaction parameters such as growth, temperature and time. The photoluminescence (PL) excitation and PL emission spectra exhibited the typical Eu³⁺ bands in the wavelength range of 200-550 nm and 400-750 nm, respectively. The intensity of the [Formula: see text] electric dipole (ED) transition peak was strong in the PL emission spectrum which imparts the red color when observed under ultraviolet light. The ED transition peak intensity increased when the sample was calcined at an elevated temperature of 700 °C, indicating improved asymmetry ratio and good chromaticity coordinates. The electrical properties of the prepared materials were studied by spin-coating the powder dispersed solutions on the silica substrate. The output current values were also measured for the CLSO nanoparticles prepared under different growth conditions. These results showed the advantages of CLSO nanoparticles for their application in optics and feasibility in nanoelectronic and energy harvesting devices.

Synthesis of enhanced phosphonic functional groups mesoporous silica for uranium selective adsorption from aqueous solutions

Enhanced phosphonic functional group (PFG)-based mesoporous silicas (MSs) were synthesized by hydrothermal method for uranium [U(VI)] selective adsorption from aqueous solutions. Considering that PFGs are directly related to U(VI) adsorption, the main idea of this research was to synthesize enhanced PFG-MSs and consequently enhance U(VI) adsorption. We synthesized two kinds of MSs based on acetic and phosphoric acids at weakly acidic pH, which allows high-loading phosphonic functionality. The main sodium and phosphonic functionality sources were sodium metasilicate and diethylphosphatoethyltriethoxysilane (DPTS). Adsorption experiment results exhibit enhanced U(VI) adsorption capacity from 55.75 mg/g to 207.6 mg/g for acetic and phosphoric acids, respectively. This finding was due to the enhancement of PFGs by phosphoric acids. The highest adsorption selectivity was 79.82% for U(VI) among the six different elements, including Pb, As, Cu, Mo, Ni, and K. Structural characterization of the samples was performed by Fourier transform infrared, X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Brunauer-Emmett-Teller analysis methods. Element concentrations were measured by inductively coupled plasma optical emission spectrometry. Several parameters affecting adsorption capacity, including pH, contact time, initial U(VI) concentration and solution volume, and adsorbent concentration, were also investigated.

Chemical Structure-Biological Activity Models for Pharmacophores' 3D-Interactions

Within medicinal chemistry nowadays, the so-called pharmaco-dynamics seeks for qualitative (for understanding) and quantitative (for predicting) mechanisms/models by which given chemical structure or series of congeners actively act on biological sites either by focused interaction/therapy or by diffuse/hazardous influence. To this aim, the present review exposes three of the fertile directions in approaching the biological activity by chemical structural causes: the special computing trace of the algebraic structure-activity relationship (SPECTRAL-SAR) offering the full analytical counterpart for multi-variate computational regression, the minimal topological difference (MTD) as the revived precursor for comparative molecular field analyses (CoMFA) and comparative molecular similarity indices analysis (CoMSIA); all of these methods and algorithms were presented, discussed and exemplified on relevant chemical medicinal systems as proton pump inhibitors belonging to the 4-indolyl,2-guanidinothiazole class of derivatives blocking the acid secretion from parietal cells in the stomach, the 1-[(2-hydroxyethoxy)-methyl]-6-(phenylthio)thymine congeners’ (HEPT ligands) antiviral activity against Human Immunodeficiency Virus of first type (HIV-1) and new pharmacophores in treating severe genetic disorders (like depression and psychosis), respectively, all involving 3D pharmacophore interactions.

Dopamine-assisted synthesis of carbon-coated silica for PCR enhancement

Polymerase chain reaction (PCR) has become one of the most popular methods to identify genomic information on cells and tissues as well as to solve crimes and check genetic diseases. Recently, the nanomaterials including nanocomposite and nanoparticles have been considered as a next generation of solution to improve both quality and productivity of PCR. Herein, taking into these demands, carbon-coated silica was synthesized using silica particles via polymerization of biocompatible dopamine (PD) to form polydopamine (PDA) film and carbonization of PDA into graphitic structures. For further investigation of the effects of as-prepared silica, PDA-coated silica (PDA silica), and carbonized PDA silica (C-PDA silica), two different types of genes were adopted to investigate the influences of them in the PCR. Furthermore, the strong interaction between the nanocomposites and PCR reagents including polymerase and primers enables regulation of the PCR performance. The effectiveness of the nanocomposites was also confirmed through adopting the conventional PCR and real-time PCR with two different types of DNA as realistic models and different kinds of analytical methods. These findings could provide helpful insight for the potential application in biosensors and biomedical diagnosis.