Preparation and Characteristics of Biocomposites Based on Steam Exploded Sisal Fiber Modified with Amphipathic Epoxidized Soybean Oil Resin

Build-To-Specification Vanillin and Phloroglucinol Derived Biobased Epoxy-Amine Vitrimers

Epoxy resins are widely used in the composite industry due to their dimensional stability, chemical resistance, and thermo-mechanical properties. However, these thermoset resins have important drawbacks. (i) The vast majority of epoxy matrices are based on non-renewable fossil-derived materials, and (ii) the highly cross-linked molecular architecture hinders their reprocessing, repairing, and recycling. In this paper, those two aspects are addressed by combining novel biobased epoxy monomers derived from renewable resources and dynamic crosslinks. Vanillin (lignin) and phloroglucinol (sugar bioconversion) precursors have been used to develop bi- and tri-functional epoxy monomers, diglycidyl ether of vanillyl alcohol (DGEVA) and phloroglucinol triepoxy (PHTE) respectively. Additionally, reversible covalent bonds have been incorporated in the network by using an aromatic disulfide-based diamine hardener. Four epoxy matrices with different ratios of epoxy monomers (DGEVA/PHTE wt%: 100/0, 60/40, 40/60, and 0/100) were developed and fully characterized in terms of thermal and mechanical properties. We demonstrate that their performances are comparable to those of commonly used fossil fuel-based epoxy thermosets with additional advanced reprocessing functionalities.

E, Bassyouni M, Zoromba M, Abdel-Aziz M, Mira H, Y. E. Fabrication and Characterization of Microcellular Polyurethane Sisal Biocomposites

In this study, microcellular polyurethane (PU)-natural fiber (NF) biocomposites were fabricated. Polyurethanes based on castor oil and PMDI were synthesized with varying volume ratios of sisal fiber. The effect of natural fiber treatment using water and alkaline solution (1.5% NaOH) and load effect were investigated. Biocomposites were mechanically and physically investigated using tensile, viscoelasticity, and water absorption tests. The interfacial adhesion between PU and sisal fiber was studied using SEM. Short NF loads (3%) showed a significant improvement in the mechanical properties of the PU-sisal composite such as modulus of elasticity, yield and tensile strength up to 133%, 14.35 % and 36.7% respectively. Viscoelastic measurements showed that the composites exhibit an elastic trend as the real compliance (J’) values were higher than those of the imaginary compliance (J’’). Increasing NF loads resulted in a decrease of J’. Applying variable temperatures (120–80 °C) caused an increase in the stiffness at different frequencies.

Preparation and Properties of Jute Fiber Long-Chain Fatty Acid Esters in Supercritical Carbon Dioxide

A two-step method involving continuous screw-extrusion steam explosion (CSESE) pretreatment and esterification in supercritical carbon dioxide (scCO₂) is used to prepare long-chain fatty acid-modified jute fiber. The weight gain percentage (WG %) of CSESE-pretreated jute laurate (JL) was 110.7% when esterification was carried out in scCO₂ at 14 MPa and 100 °C for 2 h. The corresponding WG % was 105.5% when esterification was instead carried out in pyridine at 100 °C for 2 h. Scanning electron microscopy and X-ray diffraction indicated that CSESE pretreatment enhanced the reactivity of jute fiber, with esterification in scCO₂ simultaneously occurring on the fibers surface and internal walls. The glass transition temperature of esterified jute was approximately 119 °C, indicating that it could be hot processed over a wide temperature range. The esterified jute had an oil absorption ratio of 17.01 g/g, so it can be used as an oil absorption material.