Sorption of Molybdates and Tungstates on Functionalized Montmorillonites: Structural and Textural Features

Adsorption behavior of Mo(VI) from aqueous solutions using tungstate-modified magnetic nanoparticle

A new magnetic nanoparticle modified with sodium tungstate (Mnp-Si-W) was synthesized and employed for the sorption of molybdenum from aqueous solutions. The prepared nanoparticles (Mnp-Si-W) were characterized by different advanced techniques. Different parameters that influenced the adsorption percent of Mo(VI) were investigated using a batch process. Based on a systematic investigation of the adsorption isotherms and kinetics models, Mo(VI) adsorption follows the Langmuir model and pseudo-second-order kinetics. According to the Langmuir isotherm model, the Mnp-Si-W nanoparticles exhibited a maximum adsorption capacity of 182.03 mg g-1 for Mo(VI) at pH 2.0. The effect of competing ions showed that the prepared nanoparticles have a high selectivity for the sorption of molybdenum. Moreover, the effect of some interfering anions on Mo(VI) ion sorption is found in the following order: phosphate < sulfate < chromate. Finally, the nanoparticle (Mnp-Si-W) can be successfully reused five times.

Novel Styrene-Based Polyamine Sorbent for Efficient Selective Separation of Molybdenum

Tungsten (W) and molybdenum (Mo) are important strategic resources but the two coexist in both primary ore and waste. Before a single metal product is obtained, it is often necessary to separate the two. In this work, we reported two new polyamine resins (D301@PA and D301@TA), which can be obtained by an assembled amine (primary amine or tertiary amine) and traditional D301 resin by the dipping method. Then, the sorption experiments with the amine resins were carried out, and the selectivity and sorption capacity of the two new polyamine resins for MoS₄ ^2- have been significantly improved. Among them, D301@TA showed the highest sorption capacity of 414 mg·g^-1 and a separation factor of 108. Finally, the sorption mechanism can be inferred through scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) analysis, and X-ray photoemission spectroscopy (XPS); the Cl^- ions in the amine resin and the MoS₄ ^2- ions were subjected to ion exchange. This work provides a green and efficient approach for separating tungsten and molybdenum.

Immobilization of W(VI) and/or Cr(VI) in soil treated with montmorillonite modified by a gemini surfactant and tetrachloroferrate (FeCl4-)

The coexistence of highly toxic chromium (Cr) and the emerging contaminant tungsten (W) in the soil adjacent to W mining areas is identified. Immobilization of W and/or Cr is vital for the safe utilization of contaminated soil. In this study, the cationic gemini surfactant (butane-1,4-bis(dodecyl dimethyl ammonium bromide)) and tetrachloroferrate (FeCl₄^-)-modified montmorillonite (FeOMt) was applied to investigate the retention performance of W and/or Cr in the soil. Regardless of the initially spiked amount of WO₄^2- and/or CrO₄^2-, the W and/or Cr leached in soil solution was rapidly immobilized within 5 min. The immobilization rates of W and/or Cr in the single and binary soil systems were stably maintained against the variations in pH and coexisting anion. FeOMt showed more favorable performance in the retention of W and/or Cr with respect to the precursors (i.e., the original Mt and surfactant-modified Mt) and efficiently inhibited the phytotoxicity and bioaccumulation of W and/or Cr in mung beans. Due to the ion exchange, complexation, reduction, and flocculation, the addition of FeOMt transformed W and/or Cr from exchangeable/carbonate species to reducible/oxidizable fractions, reducing the environmental risk. FeCl₄^- complex, as a byproduct of the steel pickling process in industry, plays the pivotal role in the efficient retention of W and Cr. Based on the facile synthesis procedure and the efficient performance, the use of FeOMt for the amendment of W- and/or Cr-contaminated soil is feasible and promising.

Highly efficient sorption of molybdenum from tungstate solution with modified D301 resin

The separation of molybdenum (Mo) from tungstate solution is a bottleneck problem in tungsten (W) metallurgy, and it hinders the development of high-purity tungsten materials. In this research, a modified D301 resin was used to adsorb and separate molybdenum from tungstate solution. The maximum sorption capacity (Q_e) of modified D301 for MoS₄²⁻ was found to be 428 mg g⁻¹ and the separation coefficient (β) was 108.9 when the contact time was 4 h and the reaction temperature was 25 °C and the pH value of the tungstate solution was 7.2. The sorption process conforms to Langmuir isotherm models and the quasi-second-order kinetic model. The sorption mechanism was also discussed, which was a single layered spontaneous sorption process. Theoretical calculations infer bonding behavior between the N atom on the resin and the S atom on the MoS₄²⁻ molecule. The sorption energy is −7.67 eV, which indicated that the sorption process is stable chemical sorption. The desorption experiment showed that more than 90% molybdenum could be desorbed from the loaded resin when the concentration of sodium hydroxide solution was 5 w%. Finally, after three-stage sorption–desorption, almost all molybdenum in the solution was adsorbed, achieving better separation of tungsten and molybdenum.

The modified D301 resin is prepared by assembling TOA and D301 for efficient selective adsorption of MoS₄²⁻ from tungstate solution.

Interactions of Cd2+, Co2+ and MoO42− Ions with Crushed Concrete Fines

Construction and demolition activities generate approximately two thirds of the world’s waste, with concrete-based demolition material accounting for the largest proportion. Primary aggregates are recovered and reused, although the cement-rich fine fraction is underutilised. In this study, single metal batch sorption experiments confirmed that crushed concrete fines (CCF) are an effective sorbent for the maximum exclusion of 45.2 mg g−1 Cd2+, 38.4 mg g−1 Co2+ and 56.0 mg g−1 MoO42− ions from aqueous media. The principal mechanisms of sorption were determined, by scanning electron microscopy of the metal-laden CCF, to be co-precipitation with Ca2+ ions released from the cement to form solubility limiting phases. The removal of Co2+ and MoO42− ions followed a zero-order reaction and that of Cd2+ was best described by a pseudo-second-order model. The Langmuir model provided the most appropriate description of the steady state immobilisation of Cd2+ and Co2+, whereas the removal of MoO42− conformed to the Freundlich isotherm. Long equilibration times (>120 h), loose floc formation and high pH are likely to limit the use of CCF in many conventional wastewater treatment applications; although, these properties could be usefully exploited in reactive barriers for the management of contaminated soils, sediments and groundwater.

Modification of Bentonite with Cationic and Nonionic Surfactants: Structural and Textural Features

Surfactant-modified clay minerals are known for their good sorption properties of both organic and inorganic compounds from aqueous solutions. However, the current knowledge regarding the effect of both cationic and nonionic surfactants on the properties of bentonite is still insufficient. Bentonite, with montmorillonite as the base clay, was modified with hexadecethyltrimethylammonium bromide (a cationic surfactant) in the amount of 1.0 cation exchange capacity (CEC) of bentonite and varying concentrations of t-octylphenoxypolyethoxyethanol (Triton X-100, a nonionic surfactant). We aimed to improve the understanding of the effect of nonionic and cationic surfactants on clay minerals. The modified bentonites were characterized by X-ray diffraction (XRD), thermogravimetric analysis/differential thermal analysis (TG/DTA), Fourier transform infrared spectrometry (FTIR), field emission scanning electron microscopy (SEM) and specific surface area and pore volume (BET). According to our results, the presence of a cationic surfactant significantly increased the amount of the adsorbed nonionic surfactant. Moreover, an increase in the concentration of nonionic surfactants is also associated with an increase in the effectiveness of the modification process. Our results indicate that the amount of nonionic surfactant used has a significant effect on the properties of the obtained hybrid material. Modification of bentonite with a nonionic surfactant did not cause an expansion of the interlayer space of smectite, regardless of the presence of a cationic surfactant. The modification process was found to significantly decrease the specific surface area of bentonite. Improvement of hydrophobic properties and thermal stability was also observed.