Laboratory Methods for Assessing the Influence of Improper Asphalt Mix Compaction on Its Performance

Characterization of Rutting Damage by the Change of Air-Void Characteristics in the Asphalt Mixture Based on Two-Dimensional Image Analysis

In the process of the rutting test, the air-void characteristics in asphalt mixture specimens are a dynamic change process. It is of great significance to systematically study the correlation between the change of air-void characteristics and the depth of the rutting slab and establish a relationship with damage. In this paper, the air-void information of rutting specimen sections with different loading cycles (500, 1000, 1500, 2000, 2500, and 3000 times) is obtained by two-dimensional image technology. The dynamic change process of the micro characteristics of internal air voids of two graded asphalt mixtures (AC-13 and AC-16) under cyclic wheel load is analyzed, and it is used as an index to characterize the microstructure damage of the asphalt mixture. The results show that the variation of air-void distribution, air-void shape characteristics, and air-void fractal dimension with the loading process can well characterize the permanent deformation law of the rutting slab. The fractal dimension of the air void increases with the increase in load. It is a dynamic process in which the air-void content changes with crack initiation and propagation. After rutting deformation, the total air-void area and average air-void size of the sample increase, and the total air-void number decreases. Because microcracks are formed in the specimen after rutting damage, the aspect ratio of the air void increases, and the roundness value decreases.

Use of New Green Bitumen Modifier for Asphalt Mixtures Recycling

Nowadays, an increasing amount of reclaimed asphalt pavement (RAP) is being produced from the reconstruction and/or modernisation of asphalt pavements. It is necessary to recycle the obtained RAP according to principles of sustainable development. Therefore, this work includes the design of asphalt mixtures containing RAP with bio-derived modifier and evaluates their performance properties. Crosslinked sodium alginate was applied for bitumen modification. The studies were carried out for four different modifier contents, i.e., 1.0%, 2.5%, 4.0% and 5.5%, with and without crosslinking agent. On the basis of the binder test results, the optimal amount of the additive was found to be 2.5%. The nanostructure analysis for the base and modified binders indicated a dual crosslinked biopolymer effect. As a result of the bee structure size decrease, the binder softening effect was observed. The asphalt mix properties showed that application of biopolymer-modified binder is fully justified due to the functional parameters of the mixture, especially the increased resistance to water and frost by about 9%.

The Influence of the Affinity between Aggregate and Bitumen on the Mechanical Performance Properties of Asphalt Mixtures

Two of the main problems encountered in flexible pavements are the stripping of coarse aggregates and the formation of rut depth due to increases in the volume of road traffic and heavy vehicle loads, especially in areas where speeds are low. The existence of rut depth also affects the comfort and safety of road users due to the water accumulation on the pavement surface and reducing tire/pavement friction, which can lead to hydroplaning phenomena. In this research, it was proven that the use of fillers of different origins influences the affinity between aggregates and the binder. The effect of an adhesion promoter in the mix design (such as the amine included in cellulosic fiber pellets) was also studied. Several tests were carried out to determine the binder/aggregate adhesiveness, water sensitivity and resistance to permanent deformation, to evaluate the performance of different blends. It was found that the addition of this additive increased 10% of the aggregate surfaces covered with bitumen when compared with the aggregates without this addition. As expected, the water sensitivity tests showed that the mixture with granitic filler had the lowest indirect tensile strength ratio (ITSR) value (70%), while the mixtures with limestone filler led to the highest percentages (ranging from 83 to 93%). As for the results of the wheel tracking tests (WTT), it was confirmed that the use of limestone filler translates into an improvement in the performance against the permanent deformation of the asphalt mixtures. The mixture with higher bitumen content and adhesion promoter revealed the best average results.

Testing of Materials and Elements in Civil Engineering

This issue is proposed and organized as a means to present recent developments in the field of testing of materials in civil engineering. For this reason, the articles highlighted in this issue should relate to different aspects of testing of different materials in civil engineering, from building materials and elements to building structures. The current trend in the development of materials testing in civil engineering is mainly concerned with the detection of flaws and defects in elements and structures using destructive, semi-destructive, and nondestructive testing. The trend, as in medicine, is toward designing test equipment that allows one to obtain a picture of the inside of the tested element and materials. Very interesting results with significance for building practices of testing of materials and elements in civil engineering were obtained.

Brick Debris Dust as an Ecological Filler and Its Effect on the Durability of Asphalt Mix

Brick debris is one of the main construction wastes obtained from demolition of buildings. However, this material can be successfully used in the recycling process. The purpose of the study was to determine the brick dust addition effect on asphalt surface service life. An asphalt concrete reference mix was designed for bonding layer and prepared using a Marshall compacting device. In addition, three mixes with combined lime-brick filler were prepared as well as one mix containing only brick filler. The samples were tested for their volumetric properties—density, bulk density, air void content, resistance to water and frost and stiffness modulus with varying test temperatures. It was found that 25% of brick dust addition to the filler did not considerably change the properties of the tested samples, while in the case of 50% filler the replacement stiffness and frost resistance decrease; however, the minimum required value is maintained. It can be concluded that the lime filler can be replaced with up to 50% of brick dust without a negative impact on the properties of asphalt mix. The proposed solution fits into the idea of sustainable development indicating a way of brick debris management.

Use of GRP Pipe Waste Powder as a Filler Replacement in Hot-Mix Asphalt

There is an increasing global trend to find sustainable, environmentally friendly and cost-effective materials as an alternative to limited natural raw materials. Similarly, the use of waste materials has been gaining popularity in the production of hot-mix asphalt (HMA). In this study, the sustainable use of glass-fiber-reinforced polyester (GRP) pipe waste powder (GRP-WP), gathered from the cutting and milling process of GRP pipe production, utilizing it in asphalt mixes as a filler, is evaluated based on lab testing to find out: (i) if it produces similar or better performance compared to the most conventionally available filler material (limestone) and, (ii) if so, what would be the optimum GRP-WP filler content to be used in asphalt mixes. For this reason, an experimental test matrix consisting of 45 samples with three different amounts of binder content (4%, 4.5% and 5.0%), and a 5% filler content with five different percentages of the GRP-WP content (0%, 25%, 50%, 75% and 100% replacement by weight of the filler), was prepared to figure out which sample would produce the similar Marshall stability and flow values compared to the control samples while also satisfying specification limits. It was found that the samples with 4.5% binder content, 3.75% GRP-WP and 1.25% limestone filler content produced the results both satisfying the specification requirements and providing an optimum mix design. It is believed that use of GRP-WP waste in HMA production would be a very useful way of recycling GRP-WP.

Laboratory Evaluation of a Vertical Vibration Testing Method for an SMA-13 Mixture

In order to simulate the on-site compaction conditions of a Stone Matrix Asphalt (SMA) mixture, The Vertical Vibration Testing Method (VVTM), Superpave Gyratory Compactor (SGC), and Marshall method are used to test the SMA-13 mixture, and the physical and mechanical properties of the asphalt mixture designed by these three methods are tested. Subsequently, the influences of the molding method on the mechanical properties are compared. The influence of vibration compaction time on the volume parameters of the SMA mixture is studied. Following the heavy traffic compaction standards, the vibration compaction time of the SMA mixture is determined. The results show that the densities of the heavy Marshall specimen, VVTM specimen, and SGC specimen are 1.018 times, 1.019 times, and 1.015 times greater than that of the standard Marshall specimen, respectively. The passing rate of the 4.75 mm aggregate of the standard Marshall specimen is 29.9%, and that of the VVTM specimen and SGC specimen is 31.1% and 30.5%, respectively, while that of the heavy Marshall specimen is 34.5%. The mechanical strength of the specimen can be greatly improved as the density increases. On the other hand, by the same compaction work, the mechanical strength of the VVTM specimens can be increased by at least 7% compared with the heavy Marshall specimen. The mechanical strength of the VVTM specimen is increased by at least 22% compared with the standard Marshall specimen. The results also show that under the optimal asphalt-aggregate ratio and the same compaction work, the compressive strength and shear strength of the VVTM specimens are increased by at least 6% and 9%, respectively, compared with the Marshall specimens. In summary, the performance of the asphalt mixture designed by the VVTM is superior, providing a wider choice for future asphalt mixture design.