Sustainable Additive Manufacturing: Mechanical Response of Polyethylene Terephthalate Glycol over Multiple Recycling Processes

Mechanical and Electrical Properties of Polyethylene Terephthalate Glycol/Antimony Tin Oxide Nanocomposites in Material Extrusion 3D Printing

In this study, poly (ethylene terephthalate) (PETG) was combined with Antimony-doped Tin Oxide (ATO) to create five different composites (2.0-10.0 wt.% ATO). The PETG/ATO filaments were extruded and supplied to a material extrusion (MEX) 3D printer to fabricate the specimens following international standards. Various tests were conducted on thermal, rheological, mechanical, and morphological properties. The mechanical performance of the prepared nanocomposites was evaluated using flexural, tensile, microhardness, and Charpy impact tests. The dielectric and electrical properties of the prepared composites were evaluated over a broad frequency range. The dimensional accuracy and porosity of the 3D printed structure were assessed using micro-computed tomography. Other investigations include scanning electron microscopy and energy-dispersive X-ray spectroscopy, which were performed to investigate the structures and morphologies of the samples. The PETG/6.0 wt.% ATO composite presented the highest mechanical performance (21% increase over the pure polymer in tensile strength). The results show the potential of such nanocomposites when enhanced mechanical performance is required in MEX 3D printing applications, in which PETG is the most commonly used polymer.

Investigation of the Effectiveness of Silicon Nitride as a Reinforcement Agent for Polyethylene Terephthalate Glycol in Material Extrusion 3D Printing

Polyethylene terephthalate glycol (PETG) and silicon nitride (Si3N4) were combined to create five composite materials with Si3N4 loadings ranging from 2.0 wt.% to 10.0 wt.%. The goal was to improve the mechanical properties of PETG in material extrusion (MEX) additive manufacturing (AM) and assess the effectiveness of Si3N4 as a reinforcing agent for this particular polymer. The process began with the production of filaments, which were subsequently fed into a 3D printer to create various specimens. The specimens were manufactured according to international standards to ensure their suitability for various tests. The thermal, rheological, mechanical, electrical, and morphological properties of the prepared samples were evaluated. The mechanical performance investigations performed included tensile, flexural, Charpy impact, and microhardness tests. Scanning electron microscopy and energy-dispersive X-ray spectroscopy mapping were performed to investigate the structures and morphologies of the samples, respectively. Among all the composites tested, the PETG/6.0 wt.% Si3N4 showed the greatest improvement in mechanical properties (with a 24.5% increase in tensile strength compared to unfilled PETG polymer), indicating its potential for use in MEX 3D printing when enhanced mechanical performance is required from the PETG polymer.

Effect of 3D-Printed Honeycomb Core on Compressive Property of Hybrid Energy Absorbers: Experimental Testing and Optimization Analysis

This paper presents an innovative method of constructing energy absorbers, whose primary function is to effectively transform kinetic energy into strain energy in events with high deformation rates. Hybrid specimens are proposed considering thin-walled windowed metallic tubes filled with 3D-printed hexagonal honeycombs made of PET-G and ABS thermoplastic. The patterned windows dimensions vary from 20 × 20, 20 × 30, 15 × 20 and 15 × 30 mm2. Although using polymers in engineering and thin-walled sections is not new, their combination has not been explored in this type of structure designed to withstand impacts. Specimens resist out-of-plane quasi-static axial loading, and test results are analyzed, demonstrating that polymer core gives the samples better performance parameters than unfilled samples regarding energy absorption (Ea), load rate (LR), and structural effectiveness (η). An optimization procedure using specialized software was applied to evaluate experimental results, which led to identifying the optimal window geometry (16.4 × 20 mm2, in case) and polymer to be used (ABS). The optimized sample was constructed and tested for axial compression to validate the optimization outcomes. The results reveal that the optimal sample performed similarly to the estimated parameters, making this geometry the best choice under the test conditions.

A Coherent Assessment of the Compressive Strain Rate Response of PC, PETG, PMMA, and TPU Thermoplastics in MEX Additive Manufacturing

In this study, we successfully address a significant research and engineering gap by quantitatively assessing the impact of varying compressive loading rates on the mechanical behavior of four popular thermoplastic polymers in material-extrusion-based (MEX) 3D printing. Raw powders of polycarbonate (PC), polyethylene terephthalate glycol (PETG), polymethyl methacrylate (PMMA), and thermoplastic polyurethane (TPU) were processed through melt extrusion, and the filaments were used to 3D-print the test samples. For completeness, thermogravimetric analysis and a compressive test following the ASTM-D695 standard were conducted. Ultimately, the compressive strength and yield stress, the compressive modulus of elasticity and toughness, and the maximum compressive sensitivity index were thoroughly documented. Specimens were tested in strain rates from 1.3 mm/min to 200 mm/min. The compressive strength (40% for the PMMA) and stiffness (29% for the TPU) increased with the increase in the strain rate in all polymers tested. PC had the highest strain rate sensitivity. Significant variations in deformation and fracture modes were observed and thoroughly documented throughout this study. Our findings can be useful in industrial engineering as valued design optimization input parameters in various applications involving the above-mentioned polymeric materials.

Advancing Plastic Recycling: Challenges and Opportunities in the Integration of 3D Printing and Distributed Recycling for a Circular Economy

The concept of the circular economy has emerged as a promising solution to address the mounting concerns surrounding plastic waste and the urgent need for sustainable resource management. While conventional centralized recycling remains a common practice for plastic waste, centralized facilities may prove inadequate in handling the ever-increasing volumes of plastic waste generated globally. Consequently, exploring alternative recycling methods, such as distributed recycling by additive manufacturing, becomes paramount. This innovative approach encompasses actively involving communities in recycling practices and promotes a circular economy. This comprehensive review paper aims to explore the critical aspects necessary to realize the potential of distributed recycling by additive manufacturing. In this paper, our focus lies on proposing schemes that leverage existing literature to harness the potential of distributed recycling by additive manufacturing as an effective approach to plastic waste management. We explore the intricacies of the recycling process, optimize 3D printing parameters, address potential challenges, and evaluate the mechanical properties of recycled materials. Our investigation draws heavily from the literature of the last five years, as we conduct a thorough critical assessment of DRAM implementation and its influence on the properties of 3D printing structures. Through comprehensive analysis, we reveal the potential of recycled materials in delivering functional components, with insights into their performance, strengths, and weaknesses. This review serves as a comprehensive guide for those interested in embracing distributed recycling by additive manufacturing as a transformative approach to plastic recycling. By fostering community engagement, optimizing 3D printing processes, and incorporating suitable additives, it is possible to collectively contribute to a more sustainable future while combatting the plastic waste crisis. As progress is made, it becomes essential to further delve into the complexities of material behavior, recycling techniques, and the long-term durability of recycled 3D printed components. By addressing these challenges head-on, it is feasible to refine and advance distributed recycling by additive manufacturing as a viable pathway to minimize plastic waste, fostering a circular economy and cultivating a cleaner planet for generations to come.

Innovative, simple, and green: A sample preparation method based on 3D printed polymers

The present study evaluates the capability of fifteen 3D printed thermoplastic polymers as novel stationary phases for the extraction of forty-three physicochemically diverse analytes from fortified human oral fluid samples. Prototype extraction devices were prepared in 96-well plate-compatible format using fused deposition modeling 3D printer. The sample preparation was performed with 5-step protocol utilizing 96-well plates and semiautomated benchtop shaker. All resulting extracts were analyzed via high-performance liquid chromatography (operated in reversed-phase gradient elution mode) and tandem mass spectrometry (with electrospray ionization and triple quadrupole mass spectrometer). Exceptionally favorable results were observed for three polymer types: polyamide 6 (reinforced with 15% carbon fiber), LAYFOMM-60 (polyurethane with water-soluble polyvinyl alcohol), and S-FLEX 90A (thermoplastic polyurethane). Furthermore, this study also introduces an automated and repeatable 3D printing method for the fast fabrication of high-throughput, and highly selective sample preparation devices, most of which are ready-to-use without any additional processing or chemical functionalization. As such, the proposed printing method represents a significant step towards the introduction of novel polymeric stationary phases for analytical sample preparation, thus providing laboratory personnel with a method that is safer and more convenient, while minimizing negative environmental impacts.

FDM-based additive manufacturing of recycled thermoplastics and associated composites

Hailed since the fourth industrial revolution, three-dimensional (3D) printing or additive manufacturing (AM) has been extensively implemented in various manufacturing sectors. This process is popular for generating regular products and incorporating innovative designs into the components like auxetic structures, such as fabrication of engineering products, customized implants and sophisticated biomedical devices. Over the years, one of the interesting outputs of this emerging technology is the reuse of waste thermoplastic materials to produce competent products through the fused deposition modeling (FDM) technique. The strength of FDM components produced from thermoplastic waste is lower than that of virgin plastic FDM counterparts. So, there is a need to understand the significant changes in the recycled thermoplastic material during subsequent extrusions, which are chain scission, change in viscosity and breaking strength. The use of additives has been a promising solution to improve the performance of recycled material for 3D printing applications. Hence, this study aims to provide an overview of reusing plastic waste through FDM-based 3D printing. This review summarizes the current knowledge about the effect of processing on thermo-mechanical properties of recycled plastic FDM parts and the use of various additives to improve the overall quality. In addition, two case studies from open literature have been demonstrated to explain the use of FDM and associated technology for plastic recycling.

Additive Manufacturing of Polyolefins

Polyolefins are semi-crystalline thermoplastic polymers known for their good mechanical properties, low production cost, and chemical resistance. They are amongst the most commonly used plastics, and many polyolefin grades are regarded as engineering polymers. The two main additive manufacturing techniques that can be used to fabricate 3D-printed parts are fused filament fabrication and selective laser sintering. Polyolefins, like polypropylene and polyethylene, can, in principle, be processed with both these techniques. However, the semi-crystalline nature of polyolefins adds complexity to the use of additive manufacturing methods compared to amorphous polymers. First, the crystallization process results in severe shrinkage upon cooling, while the processing temperature and cooling rate affect the mechanical properties and mesoscopic structure of the fabricated parts. In addition, for ultra-high-molecular weight polyolefins, limited chain diffusion is a major obstacle to achieving proper adhesion between adjunct layers. Finally, polyolefins are typically apolar polymers, which reduces the adhesion of the 3D-printed part to the substrate. Notwithstanding these difficulties, it is clear that the successful processing of polyolefins via additive manufacturing techniques would enable the fabrication of high-end engineering products with enormous design flexibility. In addition, additive manufacturing could be utilized for the increased recycling of plastics. This manuscript reviews the work that has been conducted in developing experimental protocols for the additive manufacturing of polyolefins, presenting a comparison between the different approaches with a focus on the use of polyethylene and polypropylene grades. This review is concluded with an outlook for future research to overcome the current challenges that impede the addition of polyolefins to the standard palette of materials processed through additive manufacturing.

Friction Stir Welding Optimization of 3D-Printed Acrylonitrile Butadiene Styrene in Hybrid Additive Manufacturing

The feasibility of joining material extrusion (MEX) 3D-printed acrylonitrile butadiene styrene (ABS) plates with the friction stir welding (FSW) process was investigated herein as a promising topic of hybrid additive manufacturing (HAM). The influence of three process parameters on the mechanical strength of the joints was thoroughly examined and analyzed with a full factorial experimental design and statistical modeling. Hereto, the welding tool pin geometry, travel speed, and rotational speed were investigated. The joint’s efficiency and quality are evaluated through tensile tests and morphological characterization. More specifically, specimens’ areas of particular interest were investigated with stereoscopic, optical, and scanning electron microscopy. Throughout the FSW experimental course, the welding temperature was monitored to evaluate the state of the ABS material during the process. The majority of the welded specimens exhibited increased mechanical strength compared with the respective ones of non-welded 3D printed specimens of the same geometry. Statistical modeling proved that all processing parameters were significant. The feasibility of the FSW process in 3D printed ABS workpieces was confirmed, making the FSW a cost-effective process for joining 3D printing parts, further expanding the industrial merit of the approach.

Multifunctional Material Extrusion 3D-Printed Antibacterial Polylactic Acid (PLA) with Binary Inclusions: The Effect of Cuprous Oxide and Cellulose Nanofibers

In this work, we present an effective process easily adapted in industrial environments for the development of multifunctional nanocomposites for material extrusion (MEX) 3D printing (3DP). The literature is still very limited in this field, although the interest in such materials is constantly increasing. Nanocomposites with binary inclusions were prepared and investigated in this study. Polylactic acid (PLA) was used as the matrix material, and cuprous oxide (Cu2O) and cellulose nanofibers (CNF) were used as nanoadditives introduced in the matrix material to enhance the mechanical properties and induce antibacterial performance. Specimens were built according to international standards with a thermomechanical process. Tensile, flexural, impact, and microhardness tests were conducted. The effect on the thermal properties of the matrix material was investigated through thermogravimetric analysis, and Raman spectroscopic analysis was conducted. The morphological characteristics were evaluated with atomic force microscopy (AFM), scanning electron microscopy (SEM), and energy-dispersive X-ray (EDS) analyses. The antibacterial performance of the prepared nanomaterials was studied against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) bacteria, with a screening agar well diffusion method. All nanocomposites prepared exhibited biocidal properties against the bacteria tested. The tested PLA/1.0 CNF/0.5 Cu2O material had 51.1% higher tensile strength and 35.9% higher flexural strength than the pure PLA material.

Recycling of 3D Printable Thermoplastic Cellulose-Composite

3D printing enables sustainable product innovations through novel design, reduced use of materials, and local manufacturing. Sustainable 3D printing can further be realized using recyclable materials. Cellulose is an abundantly available renewable material. Modified celluloses, such as thermoplastic cellulose esters, are widely used in injection molding applications. The aim of this research was to study the properties of a cellulose-based composite (cellulose acetate propionate (CAP) polymer matrix with 20 wt. % microcellulose) in injection molding and granular extrusion-based 3D printing processes over multiple recycles. The impact of the processing methods on the composite’s properties were investigated. Both injection molded and 3D printed samples were ground with plastic grinding mill to particle sizes below 3 mm after each preparation stage and reused as such in the next process cycle. Morphology, mechanical and thermal properties, and material degradation were analyzed. The thermoplastic cellulose-based compound was found to be directly recyclable for both processes without the need for any additional compounding steps. The polymer matrix was able to withstand at least seven processing cycles without degradation. However, microcellulose was found to be more sensitive to thermal stress. The mechanical and thermal properties of the cellulose-based composites remained close to initial levels throughout.