A DLC-Punch Array to Fabricate the Micro-Textured Aluminum Sheet for Boiling Heat Transfer Control

Combined Use of Surface Texturing, Plasma Nitriding and DLC Coating on Tool Steel

In cold rolling, a textured roll can be used to imprint a desired surface topography onto the sheet during rolling. This work proposes the use of diamond-like carbon (DLC) coatings to protect the surface topography of the rolls in replacement of the carcinogenic hard chrome. For that, hydrogenated amorphous carbon (a-C:H) was deposited on plasma nitrided tool steel, both for ground and textured specimens. Changes in surface topography due to DLC coating were assessed using a confocal microscope. Coating adhesion was evaluated using the method VDI 3198. The specimens were characterized using X-ray diffraction (XRD), microhardness test and scanning electron microscopy (SEM). The coating was characterized using Raman spectroscopy (RS) and X-ray photoelectron spectroscopy (XPS). The results showed a soft multilayer coating consisting of a plasma nitrided layer for load support, a Si-rich interlayer to improve adhesion and an a-C:H top layer. DLC deposition reduced the roughness of the textured specimens. The coating resulted in relatively stable friction and good durability, with small damage and negligible wear even under dry sliding.

Femtosecond Laser Micro-/Nano-Texturing of Stainless Steels for Surface Property Control

Surface geometry has had an influence on the surface property, in addition to the intrinsic surface energy, of materials. Many physical surface modification methods had been proposed to control the solid surface geometry for modification of surface properties. Recently, short-pulse lasers were utilized to perform nano-texturing onto metallic and polymer substrates for the improvement of surface properties. Most of the papers reported that the hydrophilic metallic surface was modified to have a higher contact angle than 120–150°. Little studies explained the relationship between surface geometry and surface properties. In the present study, the laser micro-/nano-texturing was developed to describe this surface-geometric effect on the static contact angles for pure water. Micropatterns with multi spatial frequencies are designed and synthesized into a microtexture. This tailored microtexture was utilized to prepare for computer aided machining (CAM) data to control the femtosecond laser beams. The nano-length ripples by laser induced periodic surface structuring (LIPSS) supposed onto this microtexture to form the micro-/nano-texture on the AISI304 substrate surface. Computational geometry was employed to describe this geometric profile. The fractal dimension became nearly constant by 2.26 and insensitive to increase of static contact angle (θ) for θ > 150°. Under this defined self-similarity, the micro-/nano-textured surface state was controlled to be super-hydrophobic by increasing the ratio of the highest spatial frequency in microtextures to the lowest one. This controllability of surface property on the stainless steels was supported by tailoring the wavelength and pitch of microtextures. Exposure testing was also used to evaluate the engineering durability of this micro-/nano-textured surface. Little change of the measured fractal dimension during the testing proved that this physically modified AISI304 surface had sufficient stability for its long-term usage in air.

Plasma Printing of an AISI316 Micro-Meshing Punch Array for Micro-Embossing onto Copper Plates

Packaging using thermoplastic molding for hollowed GaN chips were requested for a leak-proof micro-joining between plastic molds and copper-based substrates. The design and engineering of micro-textures is a key technology for putting leak-proof packaging into practice. In the present paper, a micro-meshing punch array was prepared using plasma-nitriding-assisted printing. Two-dimensional original patterns were screen-printed onto an AISI316 die substrate and plasma nitrided at 673 K for 14.4 ks (or 4 h). The unprinted surfaces were selectively nitrogen super-saturated to have more nitrogen content than 5 mass% and a higher hardness than 1200 HV. The printed surfaces were selectively sand blasted to fabricate the micro-meshing punch array for micro-embossing. A computer numerically controlled stamping system was utilized to describe the micro-embossing behavior onto copper substrates and to investigate how the micro-textures on the array was transcribed onto the copper. Reduction of takt time as well as flexibility in the micro-grooving were discussed with reference to the picosecond laser machining and mechanical milling processes.

Plasma Oxidation Printing into DLC and Graphite for Surface Functionalization

A diamond-like carbon (DLC) film, coated on a AISI420-J2 stainless steel substrate and vertically aligned graphite (VAG), was structured by high-density plasma oxidation to work as a DLC-punch for micro-stamping and DLC-nozzle array for micro-dispensing, in addition to acting as a copper-plated thermal spreader, respectively. Thick DLC films were micro-patterned by maskless lithography and directly plasma-etched to remove the unmasked regions. Thick VAG (Ca plates were micro-patterned by screen-printing and selectively etched to activate the surface. Raman spectroscopy as well as electric resistivity measurement proved that there was no degradation of VAG by this surface activation. Wet plating was utilized to prove that copper wettability was improved by this surface treatment.