Experimental and Theoretical Studies of Methyl Orange Uptake by Mn-Rich Synthetic Mica: Insights into Manganese Role in Adsorption and Selectivity

Sorption behavior of chitosan nanoparticles for single and binary removal of cationic and anionic dyes from aqueous solution

In this study, chitosan nanoparticles (ChNs) were used as an adsorbent for single and simultaneous uptake of cationic (methylene blue (MB)) and anionic (methyl orange (MO)) dyes. ChNs were prepared based on the ionic gelation method using sodium tripolyphosphate (TPP) and characterized by zetasizer, FTIR, BET, SEM, XRD, and pHPZC. The studied parameters that affect removal efficiency included pH, time, and dyes' concentration. The results showed that in single-adsorption mode, the removal of MB is better in alkaline pH, contrary to MO uptake which presents higher removal efficiency in acidic media. The simultaneous removal of MB and MO from the mixture solution by ChNs could be achieved under neutral conditions. The adsorption kinetic results showed that adsorption of MB and MO for both single-adsorption and binary adsorption systems comply with the pseudo-second-order model. Langmuir, Freundlich, and Redlich-Peterson isotherms were used for the mathematical description of single-adsorption equilibrium, while non-modified Langmuir and extended Freundlich isotherms were used to fit the co-adsorption equilibrium results. The maximum adsorption capacities of MB and MO in a single dye adsorption system were 315.01 and 257.05 mg/g for MB and MO, respectively. On the other hand, and for binary adsorption system, the adsorption capacities were 49.05 and 137.03 mg/g, respectively. The adsorption capacity of MB decreases in solution containing MO and vice versa, suggesting an antagonistic behavior of MB and MO on ChNs. Overall, ChNs could be a candidate for single and binary removal of MB and MO in dye-containing wastewater.

Sodium alginate-modified alkali-activated eggshell/Fe3O4 nanoparticles: A magnetic bio-based spherical adsorbent for cationic dyes adsorption

Herein, a mixture of eggshell (ES) and magnetite nanoparticles (MNPs) was alkali-activated using NaOH/Na2SiO3 solution and then, impregnated with sodium alginate (SA) to prepare a magnetic bio-based adsorbent (namely SAAES/SA/MNPs) for the decontamination of water containing basic dyes, in particular, methylene blue (MB) and crystal violet (CV). The physicochemical properties of magnetic spheres of SAAES/SA/MNPs were characterized using XRD, FTIR, FESEM, EDX, elemental mapping, TEM, and zeta potential techniques. Dye adsorption equilibrium was studied experimentally at pH 8.0 and 25-55 °C, and a statistical physics multilayer model was applied to understand the removal mechanism of these dyes including the adsorption orientations on the adsorbent surface. The number of adsorbed dye molecules per functional group (n) of this bio-based adsorbent ranged from 0.70 to 0.91, indicating the presence of vertical and horizontal adsorption orientations for these organic molecules at all tested solution temperatures. The calculated saturation adsorption capacities (Qsat) were 332.57-256.62 mg/g for CV and 304.47-240.62 mg/g for MB, and an exothermic adsorption was observed for both adsorbates. The estimated adsorption energies (∆E) were < 25 kJ/mol, confirming that the SAAES/SA/MNPs-dye interactions were governed by physical forces as electrostatic interactions. This bio-based adsorbent was effectively regenerated using ethanol and it can be reused showing a removal of 71 and 74 % of MB and CV, respectively, after fourth adsorption-desorption cycles. Overall, the results of this article suggest the attractive performance of SAAES/SA/MNPs for removing basic dyes from aqueous solutions, thus highlighting the promising potential of this magnetic bio-based adsorbent for sustainable wastewater treatment at an industrial level.

A Study on Enhanced Electrorheological Performance of Plate-like Materials via Percolation Gel-like Effect

The use of plate-like materials to induce a percolation gel-like effect in electrorheological (ER) fluids is sparsely documented. Hence, we dispersed plate-like materials, namely natural mica, synthetic mica, and glass, as well as their pulverized particles, in various concentrations in silicone oil to form ER fluids. Subsequently, the rheological properties of the fluids were evaluated and compared to identify the threshold concentration for percolating a gel-like state. The shear stress and viscoelastic moduli under zero-field conditions confirmed that plate-like materials can be used to induce percolation gel-like effects in ER fluids. This is because of the high aspect ratio of the materials, which enhances their physical stability. In practical ER investigations, ER fluids based on synthetic mica (30.0 wt%) showed the highest yield stress of 516.2 Pa under an electric field strength of 3.0 kV mm-1. This was attributed to the formation of large-cluster networks and additional polarization induced by the ions. This study provides a practical approach for developing a new type of gel-like ER fluid.

Utilization of Foamed Glass as an Effective Adsorbent for Methylene Blue: Insights into Physicochemical Properties and Theoretical Treatment

This study reports a potential approach for the valorization of glass waste (GW) that is mainly composed of amorphous silica to prepare lightweight foamed glass (FG). The preparation of FG was achieved by mixing sodium hydroxide with GW powder followed by sintering at a temperature of 800 °C. As-synthesized FG was characterized and applied as an effective adsorbent for the removal of hazardous organic water contaminants, in particular, methylene blue (MB) dye. FG exhibited porosity of 91%, bulk density of 0.65 g/cm³, compressive strength of 4 MPa, and thermal conductivity of 0.27 W/m·K. Theoretical treatment indicated that a monolayer model with one energy site was the best in fitting the removal of MB molecules. The number of MB molecules per active site (n) ranged from 2.20 to 1.70, suggesting vertical orientation and a multi-molecular adsorption mechanism. The density of FG receptor sites (D_M) increased with the temperature, and this parameter played a vital role in the adsorption process. The adsorption capacity (Q_sat) increased from 255.11 to 305.58 mg/g, which signifies endothermic interactions. MB adsorption on FG was controlled by physical forces such as electrostatic interactions (i.e., the adsorption energies were <20 kJ/mol). The results of this study prove the feasibility of glass waste as an effective and low-cost adsorbent for water remediation.

Prediction of methyl orange dye (MO) adsorption using activated carbon with an artificial neural network optimization modeling

In this study, methyl orange (MO) dye removal by adsorption utilizing activated carbon made from date seeds (DPAC) was modeled using an artificial neural network (ANN) technique. Instrumental investigations such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) analysis were used to assess the physicochemical parameters of adsorbent. By changing operational parameters including adsorbent dosage (0.01-0.03 g), solution pH 3-8, initial dye concentration (5-20 mg/L), and contact time (2-60 min), the viability of date seeds for the adsorptive removal of methyl orange dye from aqueous solution was assessed in a batch procedure. The system followed the pseudo 2nd order kinetic model for DPAC adsorbent, according to the kinetic study (R2 = 0.9973). The mean square error (MSE), relative root mean square error (RRMSE), root mean square error (RMSE), mean absolute percentage error (MAPE), relative error (RE), and correlation coefficient (R2) were used to measure the ANN model performance. The maximum RE was 8.24% for the ANN model. Two isotherm models, Langmuir and Freundlich, were studied to fit the equilibrium data. Compared with the Freundlich isotherm model (R2 = 0.72), the Langmuir model functioned better as an adsorption isotherm with R2 of 0.9902. Thus, this study demonstrates that the dye removal process can be predicted using an ANN technique, and it also suggests that adsorption onto DPAC may be employed as a main treatment for dye removal from wastewater.

New insights into the selective adsorption mechanism of cationic and anionic dyes using MIL-101(Fe) metal-organic framework: Modeling and interpretation of physicochemical parameters

In the current study, iron-based metal organic framework (MOF) MIL-101(Fe) was successfully prepared via a facile solvothermal method. The as-synthesized MIL-101(Fe) was characterized by XRD, FE-SEM, FTIR, TGA and zeta potential techniques, and then employed as an adsorbent for methyl orange (MO) and methylene blue (MB) dyes. The adsorbed quantities of MO (1067 to 831 mg/g) were higher than those of MB (402 to 353 mg/g) indicating the high selectivity of MIL-101(Fe) towards the anionic dye at all temperatures (20-60 °C). Adsorption processes of MO and MB followed the pseudo-second order kinetics and the Langmuir equilibrium model. The interaction mechanism at a molecular level was analyzed and deeply interpreted via the advanced multilayer adsorption model. Steric parameters indicated that MO molecular aggregation (n) was 0.95-1.33 thus signifying the presence of multi-docking and multi-interactions mechanisms. The aggregated number of MB was superior to unity (i.e., n = 1.17-1.78) suggesting a vertical adsorption position and a multi-interactions mechanism at all operating temperatures. The density of MIL-101(Fe) active sites (D_{M =} 77.33-52.38 mg/g for MB and 149.91-107.07 for MO) and the total adsorbed dye layers (N_t = 3.12-2.49 for MB and 5.36-3.67 for MO) resulted in improving the adsorption capacities of MO dye. The adsorption energies ranged from 8.89 to 33.73 kJ/mol and they displayed that MO and MB uptake processes were exothermic controlled by physical interactions at all temperatures. Regeneration results indicated that this adsorbent can be reutilized without a significant loss in its removal efficiency after five adsorption-desorption cycles. Overall, the adsorption capacity, chemical stability, and regeneration performance of MIL-101(Fe) support its application as a very promising adsorbent for the removal of organic hazardous pollutants from water.

Insights Into the Mn(VII) and Cr(VI) Adsorption Mechanisms on Purified Diatomite/MCM-41 Composite: Experimental Study and Statistical Physics Analysis

In this study, a purified diatomite (PD) with a concentration of diatom frustules more than 92% SiO₂ was utilized to synthesize a composite of MCM-41 silica under hydrothermal conditions. The as-synthesized PD/MCM-41 composite was characterized and tested as an adsorbent for the removal of Cr(VI) and Mn(VII) ions from aqueous solution. Results of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Fourier-transform infrared spectroscopy (FTIR) revealed that the diatom frustules of the PD were coated with MCM-41 mesoporous silica. Experimental isotherms of Cr(VI) and Mn(VII) adsorption were fitted to classical and advanced statistical physics models at 25°C–55°C and pH 3. The Langmuir model estimated monolayer adsorption capacities ranging from 144.1 to 162.2 mg/g for Cr(VI) and 166.2 to 177.0 mg/g for Mn(VII), which improved with increasing the solution temperature. Steric and energetic parameters obtained from a monolayer adsorption model with one adsorption site was utilized to explain the adsorption mechanism at a microscopic level. The number of Cr(VI) and Mn(VII) ions adsorbed on PD/MCM-41 active site (n) were 1.25–1.27 for Cr(VI) and 1.27–1.32 for Mn(VII), thus suggesting multi-interaction mechanisms. The density of PD/MCM-41 active sites (D_M) was a key parameter to explain the adsorption of these heavy metals. The adsorbed quantities were maximum at 55°C, thus obtaining 102.8 and 110.7 mg/g for Cr(VI) and Mn(VII), respectively. Cr(VI) and Mn(VII) adsorption energies ranged from 18.48 to 26.70 kJ/mol and corresponded to an endothermic adsorption with physical forces. Entropy, free enthalpy, and internal energy associated to the adsorption of Cr(VI) and Mn(VII) ions were calculated, thus indicating that the removal of these pollutants was spontaneous. Overall, this article offers new interpretations for the Cr(VI) and Mn(VII) adsorption mechanisms on PD/MCM-41 composite, which are relevant to contribute to the development of effective water treatment processes.

Evaluation of Amine Functionalized Thermal Power Plant Solid Waste for Industrial Wastewater Remediation

Micro/nanoparticles generated after the combustion of coal/lignite in the thermal power plants were modified with amino groups of (3-aminopropyl) triethoxysilane (APTES). These silane-based functional particles were applied in textile dye (xylenol orange, XO and methyl orange, MO) removal process to deal with an industrial wastewater problem. The maximum adsorption efficiencies of APTES coated micro/nanoparticles for MO and XO dye molecules were calculated to be around 98% and 75%, respectively. The adsorption behavior of the LCFA against dyes is also assessed by investigating the effect of adsorbent dosage, contact time, pH, and temperature. The optimum dye removal was observed at a pH of 4.0, and the equilibrium was achieved within 5 min. The maximum uptake capacities of LCFA-APTES for MO and XO dye molecules were calculated to be around 17.91 and 14.72 mg g−1, respectively. This value is approximately 3 − 5 times higher than the similar adsorbent in the literature. The uptake mechanism of MO and XO dyes onto LCFA-APTES is governed by electrostatic interaction and hydrogen bonding between dye molecules and APTES. The surface chemical modifications and the nature of functional groups were ascertained by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), X-ray fluorescence (XRF), and X-ray photoelectron spectroscopy (XPS). The application of recovered micro/nanoparticles from solid wastes and their utilization for wastewater treatment is important not only for economy of developing countries but also for protecting the environment.

Outstanding Performance of a New Exfoliated Clay Impregnated with Rutile TiO2 Nanoparticles Composite for Dyes Adsorption: Experimental and Theoretical Studies

Pure rutile TiO2 nanoparticles (Rt) were combined with exfoliated black clay (BC) to prepare a new composite for water decontamination, in particular, for the uptake of methylene blue (MB) and methyl orange (MO) dyes. The as-prepared Rt/BC was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and Field emission scanning electron microscopy (FESEM) techniques, and the dyes’ adsorption isotherms at three temperatures (i.e., 25, 40, and 50 °C) were studied. The results indicated that Rt/BC displayed a high removal performance for MO (96.7%) and MB (91.4%) at pH 3.0 and 8.0, respectively. Adsorption data of MB and MO were adjusted by a double layer model at all temperatures. The theoretical parameters of this statistical physics model were interpreted to understand the MO and MB adsorption mechanisms at the molecular level. The removed molecules per active site (n) of Rt/BC ranged from 1.12 to 1.29 for MB and 1.47 to 1.85 for MO, thus representing parallel orientation and multi-interactions mechanisms (i.e., van der Waals forces, hydrogen bonding, and electrostatic interactions were involved). The Rt/BC composite had a density of surface adsorption sites of 100 mg/g. The aggregation of MO molecules was high and increased their adsorption capacities (Qsat = 294–370 mg/g) compared to that of MB (Qsat = 214–249 mg/g). Adsorption energies were 9.70–20.15 kJ/mol, and these values indicated that MO and MB adsorption processes were endothermic and occurred via physical interactions. Overall, the low cost, high regeneration performance, and stability of Rt/BC support its application as a promising adsorbent for organic pollutants from wastewaters.

Preparation of Sodalite and Faujasite Clay Composite Membranes and Their Utilization in the Decontamination of Dye Effluents

The present work describes the deposition of two zeolite films, sodalite and faujasite, by the hydrothermal method to tune the mesopores of clay support, which are prepared from a widely available clay depot from the central region of Morocco (Midelt). The clay supports were prepared by a powder metallurgy method from different granulometries with activated carbon as a porosity agent, using uniaxial compression followed by a sintering process. The 160 µm ≤ Φ ≤ 250 µm support showed the highest water flux compared to the supports made from smaller granulometries with a minimum water flux of 1405 L.m⁻²·h⁻¹ after a working time of 2 h and 90 min. This support was chosen for the deposition of sodalite (SOM) and faujasite (FAM) zeolite membranes. The X-ray diffraction of sodalite and faujasite showed that they were well crystallized, and the obtained spectra corresponded well with the sought phases. Such findings were confirmed by the SEM analysis, which showed that SOM was crystalized as fine particles while the FAM micrographs showed the existence of crystals with an average size ranging from 0.53 µm to 1.8 µm with a bipyramidal shape and a square or Cubo octahedral base. Nitrogen adsorption analysis showed that the pore sizes of the supports got narrowed to 2.28 nm after deposition of sodalite and faujasite. The efficiencies of SOM and FAM membranes were evaluated by filtration tests of solutions containing methyl orange (MO) using a flow loop, which were developed for dead-end filtration. The retention of methylene orange (MO) followed the order: SOM > FAM > 160 µm ≤ Φ ≤ 250 µm clay support with 55%, 48% and 35%, respectively. Size exclusion was the predominant mechanism of filtration of MO through SOM, FAM, and the support. However, the charge repulsion between the surface of the membrane and the negatively charged MO have not been ruled out. The point of zero charge (pzc) of the clay support, SOM and FAM membrane were pHpzc = 9.4, pHpzc = 10.6, and pHpzc = 11.4, respectively. Filtrations of MO were carried out between pH = 5.5 and pH = 6.5, which indicated that the surface of the membranes was positively charged while MO was negatively charged. The interaction of MO with the membranes might have happened through its vertical geometry.

Polyaniline nanofibers, a nanostructured conducting polymer for the remediation of Methyl orange dye from aqueous solutions in fixed-bed column studies

Polyaniline nanofibers (PANI NFs) were synthesized and employed as potential adsorbents in a continuous flow fixed-bed column adsorption study for an organic dye, Methyl Orange (MO) removal from water. These nanostructured adsorbents were characterized using ATR-FTIR, FE-SEM, HR-TEM, TGA, BET, XRD, XPS, and the Zeta-sizer. Morphological representations from SEM and TEM analyses showed that the fibers were nanosized with diameters lower than 80 nm and an interconnected network possessing a smooth surface. The SBET of the PANI NFs was found to be 35.80 m2/g. The impact of column design parameters for instance; influent concentration, flow rate, and bed mass was investigated using pH 4 influent MO solutions optimized through batch studies. The best influent concentration, bed length, and flow rate for this study were determined as 25 mg/L, 9 cm (6 g), and 3 mL/min, respectively. The column information was fitted in Thomas, Yoon-Nelson, and Bohart-Adams models. It appeared that the Thomas and Yoon-Nelson models described the data satisfactorily. The PANI NFs were able to treat 29.16 L of 25 mg/L MO solution at 9 cm bed length. A sulfate peak in a de-convoluted sulfur spectrum using XPS verified the successful adsorption of Methyl Orange.