Formulation and Characterization of Aceclofenac-Loaded Nanofiber Based Orally Dissolving Webs

Recent developments in nanofiber-based fast-disintegrating drug delivery systems

INTRODUCTION

Fast-disintegrating electrospun fibers are emerging as innovative systems for oral drug delivery. These fibers possess a high surface area, porosity, and customizable hydrophilicity, which facilitates quick drug release by disintegrating rapidly in biological fluids or upon contact with water.

AREAS COVERED

Hydrophilic polymers and cyclodextrins (CDs), either separately or in combination, are frequently utilized to accelerate the disintegration of electrospun fibers, enhance the solubility of hydrophobic drugs, and improve drug bioavailability, leading to better therapeutic outcomes. Toward this goal, a systematic literature search was conducted to identify experimental studies (2019-2025) in Web of Science, Google Scholar, and Scopus using the keywords ('fast-disintegrating' OR 'fast-dissolving') AND ('electrospinning' OR 'electrospun') AND ('delivery' OR 'release').

EXPERT OPINION

This review examines recent advancements over the past five years in the development of fast-disintegrating drug delivery fibers. It analyzes fiber composition, structural modifications, drug encapsulation routes, and their impact on drug release for oral mucosal delivery. Additionally, it addresses the challenges faced and outlines future directions in the field.

Dynamic Behavior of the Glassy and Supercooled Liquid States of Aceclofenac Assessed by Dielectric and Calorimetric Techniques

Aceclofenac (ACF), a non-steroidal anti-inflammatory drug, was obtained in its amorphous state by cooling from melt. The glass transition was investigated using dielectric and calorimetric techniques, namely, dielectric relaxation spectroscopy (DRS), thermally stimulated depolarization currents (TSDC), and conventional and temperature-modulated differential scanning calorimetry (DSC and TM-DSC). The dynamic behavior in both the glassy and supercooled liquid states revealed multiple relaxation processes. Well below the glass transition, DRS was able to resolve two secondary relaxations, γ and β, the latter of which was also detectable by TSDC. The kinetic parameters indicated that both processes are associated with localized motions within the molecule. The main (α) relaxation was clearly observed by DRS and TSDC, and results from both techniques confirmed a non-Arrhenian temperature dependence of the relaxation times. However, the glass transition temperature (Tg) extrapolated from DRS data significantly differed from that obtained via TSDC, which in turn showed reasonable agreement with the calorimetric Tg (Tg-DSC = 9.2 °C). The values of the fragility index calculated by the three experimental techniques converged in attributing the character of a moderately fragile glass former to ACF. Above the α relaxation, TSDC showed a well-defined peak. In DRS, after "removing" the high-conductivity contribution using ε' derivative analysis, a peak with shape parameters αHN = βHN = 1 was also detected. The origin of these peaks, found in the full supercooled liquid state, has been discussed in the context of structural and dynamic heterogeneity. This is supported by significant differences observed between the FTIR spectra of the amorphous and crystalline samples, which are likely related to aggregation differences resulting from variations in the hydrogen bonds between the two phases. Additionally, the pronounced decoupling between translational and relaxational motions, as deduced from the low value of the fractional exponent x = 0.72, derived from the fractional Debye-Stokes-Einstein (FDSE) relationship, further supports this interpretation.

Fabrication and In-Vivo Evaluation of Polyvinyl pyrrolidone/Poloxamer 188 Hybrid Nanofibers of Deflazacort

The superior flexibility, efficient drug loading, high surface-to-volume ratio, ease of formulation, and cost-controlled production are considered exceptional advantages of nanofibers (NFs) as a smart delivery system. Deflazacort (DEF) is an anti-inflammatory and immunosuppressant agent. It is categorized as a poorly soluble class II drug. In this study, DEF-loaded polymeric nanofibrous using the electrospinning technique mats, Polyvinyl pyrrolidone (PVP) with or without Poloxamer 188 (PX) were used as mat-forming polymers. Microscopical imaging, drug content (%), and in vitro dissolution studies were conducted for all NFs formulae (F1-F7). All NFs improved the DEF dissolution compared to the unprocessed form, with the superiority of the PVP/PX hybrid. The optimized formula (F7) exhibited an average diameter of 655.46 ± 90.4 nm and % drug content of 84.33 ± 5.58. The dissolution parameters of DEF loaded in PVP/PX NFs (F7) reflected a release of 95.3 % ± 3.1 and 102.6 % ± 1.7 after 5 and 60 min, respectively. NFs (F7) was investigated for drug-polymer compatibility using Fourier-Transform Infrared Spectroscopy (FTIR), Powder X-ray diffraction analysis (PXRD), and Differential Scanning Calorimetry (DSC). In vivo anti-inflammatory study employing male Sprague-Dawley rats showed a significant reduction of rat paw edema for F7 (p < 0.05) compared with unprocessed DEF with a normal epidermal and dermal skin structure comparable to the healthy negative control. Immunohistochemical and morphometric data displayed similarities between the immune reaction of F7 and the negative healthy control. The finding of this work emphasized that DEF loaded in PVP/PX NFs could be considered a useful strategy for enhancing the therapeutic performance of DEF.

Optimizing the fabrication of electrospun nanofibers of prochlorperazine for enhanced dissolution and permeation properties

Despite being an approved antiemetic for more than five decades, the clinical usefulness of prochlorperazine is limited by its low solubility and inconsistent absorption in the gastrointestinal tract, which presents challenges for nanotherapeutic interventions. Here, we report the preparation of a highly soluble and permeable nanofiber formulation of prochlorperazine using the Quality-by-Design approach. The final nanofiber formulation with drug entrapment of 88.02 ± 1.14 % was obtained at 20.0 kV, with a flow rate of 0.5 ml/h and tip-to-collector distance of 19.9 cm. Physio-mechanical properties, such as thickness (0.42 ± 0.02 mm), pH resistance (7.04 ± 0.08), folding endurance (54 ± 5), and tensile strength (0.244 ± 0.02 N.mm-2), were appropriate for packaging and application to oromucosal surfaces. The content uniformity (93.48-106.63 %) and weight variation (<1.8 mg) of the optimal nanofiber formulation were within the permissible limits prescribed for orodispersible films. Microscopical investigations confirm a randomly deposited and dense network of woven nanofibers with an average diameter of 363 ± 5.66 nm. The drug particles were embedded homogeneously on the fiber in the nanoform (4.27 ± 1.34 nm). The spectral analysis using TEM-EDS shows diffraction peaks of sulfur and chlorine, the elemental constituents of prochlorperazine. The drug was amorphized in the nanofiber formulation, as led by the decline of the crystallinity index from 87.25 % to 7.93 % due to electrostatic destabilization and flash evaporation of the solvent. The enthalpy of fusion values of the drug in the nanofiber mat decreased significantly to 23.6 J/g compared to its pristine form, which exhibits a value of 260.7 J/g. The nanofibers were biocompatible with oral mucosal cells, and there were no signs of mucosal irritation compared to 1 % sodium lauryl sulfate. The fiber mats rapidly disintegrated within <1 s and released ≈91.49 ± 2.1 % of the drug within 2 min, almost 2-fold compared to the commercial Stemetil MD® tablets. Similarly, the cumulative amount of the drug permeated across the unit area of the oromucosal membrane was remarkably high (31.28 ± 1.30 μg) compared to 10.17 ± 1.11 μg and 13.10 ± 1.79 μg from the cast film and drug suspension. Our results revealed these nanofiber formulations have the potential to be fast-dissolving oromucosal delivery systems, which can result in enhanced bioavailability with an early onset of action due to rapid disintegration, dissolution, and permeation.

Aceclofenac/Citronellol Oil Nanoemulsion Repurposing Study: Formulation, In Vitro Characterization, and In Silico Evaluation of Their Antiproliferative and Pro-Apoptotic Activity against Melanoma Cell Line

Aceclofenac (ACF) is a widely used non-steroidal anti-inflammatory drug (NSAID) known for its effectiveness in treating pain and inflammation. Recent studies have demonstrated that ACF possesses antiproliferative properties, inhibiting the growth of cancer cells in various cancer cell lines. Citronellol, a monoterpenoid alcohol found in essential oils, exhibits antioxidant properties and activities such as inhibiting cell growth and acetylcholinesterase inhibition. In this study, the objective was to formulate and evaluate an aceclofenac/citronellol oil nanoemulsion for its antiproliferative effects on melanoma. The optimal concentrations of citronellol oil, Tween 80, and Transcutol HP were determined using a pseudoternary phase diagram. The formulated nanoemulsions were characterized for droplet size, zeta potential, thermophysical stability, and in vitro release. The selected formula (F1) consisted of citronellol oil (1 gm%), Tween 80 (4 gm%), and Transcutol HP (1 gm%). F1 exhibited a spherical appearance with high drug content, small droplet size, and acceptable negative zeta potential. The amorphous state of the drug in the nanoemulsion was confirmed by Differential Scanning Calorimetry, while FTIR analysis indicated its homogenous solubility. The nanoemulsion showed significant antiproliferative activity, with a lower IC50 value compared to aceclofenac or citronellol alone. Flow cytometric analysis revealed cell cycle arrest and increased apoptosis induced by the nanoemulsion. In silico studies provided insights into the molecular mechanism underlying the observed antitumor activity. In conclusion, the developed aceclofenac/citronellol oil nanoemulsion exhibited potent cytotoxicity and pro-apoptotic effects, suggesting its potential as a repurposed antiproliferative agent for melanoma treatment. In a future plan, further animal model research for validation is suggested.

Optimization and Production of Aceclofenac-Loaded Microfiber Solid Dispersion by Centrifugal Spinning

Aceclofenac-loaded polyvinylpyrrolidone fiber-based amorphous solid dispersion was produced successfully by centrifugal spinning. The solution concentration and rotational speed were optimized to produce the fiber-based drug carrier system, with a determined production rate of 12.7 g/h dry solid fibers. The obtained fibers were bead-free and smooth-surfaced with an average diameter of 7.5 ± 2.5 μm. Gas chromatographic determinations revealed that ethanol, as a residual solvent, was well below the regulatory limit of 0.5%. Differential scanning calorimetric investigation and infrared spectroscopic measurements were used to track the physicochemical changes that intervene during fiber formation in the solid state. The results revealed that the rapid evaporation of the solvent was accompanied by a probable crystalline to amorphous transition of the active substance during centrifugal spinning. In vitro dissolution studies revealed an instantaneous disintegration of the fibrous structure and a rapid release of the active substance, with the microfibrous webs greatly outperforming the crystalline active substance, especially in the early time-points. This implies that centrifugal spinning offers a viable scale-up production process to prepare drug-loaded fiber-based solid dispersions.

Electrospun nanofibres in drug delivery: advances in controlled release strategies

Emerging drug-delivery systems demand a controlled or programmable or sustained release of drug molecules to improve therapeutic efficacy and patient compliance. Such systems have been heavily investigated as they offer safe, accurate, and quality treatment for numerous diseases. Amongst newly developed drug-delivery systems, electrospun nanofibres have emerged as promising drug excipients and are coming up as promising biomaterials. The inimitable characteristics of electrospun nanofibres in terms of their high surface-to-volume ratio, high porosity, easy drug encapsulation, and programmable release make them an astounding drug-delivery vehicle.

Effects of electrospun fiber curcumin on bisphenol A exposed Caco-2 cells

Curcumin; the major polyphenolic compound, isolated from Curcuma longa L.; loaded polyvinylpyrrolidone K90 fibers were prepared using electrospinning method. Effectiveness was tested on human colorectal adenocarcinoma cells with the presence of the endocrine disrupter Bisphenol A. Curcumin-loaded fibers were shown to have good physicochemical properties where excellent morphology of the electrospin fibers were formed. With the presence of 8 nM Bisphenol A, 17.37 mM fibers were found to inhibit proliferation in the cells in a dose-dependent manner. Fibers induced a significant increase in malondialdehyde by Thiobarbituric Acid Reactive Substances Assay compared to the control and this effect was supported by the presence of Bisphenol A. Western blot results indicate Super Oxide Dismutase-1 levels were increased by fiber, while Bisphenol A coincubated group resulted in a decrease. Fibers increased the expression of Estrogen Receptor 2, while Estrogen Receptor 1 expression did not change. Estrogen Receptor 2 expression was increased by coincubation with Bisphenol A; indicating a possible role of Estrogen Receptor 2 in the protective effects of fiber. This study presents that fiber had enhanced bioavailability and solubility with increased anticancer effect in human colon adenocarcinoma cells in presence of Bisphenol A; where involved mechanisms are antioxidant system and estrogen receptor expression.

Continuous downstream processing of milled electrospun fibers to tablets monitored by near-infrared and Raman spectroscopy

Electrospinning is a technology for manufacture of nano- and micro-sized fibers, which can enhance the dissolution properties of poorly water-soluble drugs. Tableting of electrospun fibers have been demonstrated in several studies, however, continuous manufacturing of tablets have not been realized yet. This research presents the first integrated continuous processing of milled drug-loaded electrospun materials to tablet form supplemented by process analytical tools for monitoring the active pharmaceutical ingredient (API) content. Electrospun fibers of an amorphous solid dispersion (ASD) of itraconazole and poly(vinylpyrrolidone-co-vinyl acetate) were produced using high speed electrospinning and afterwards milled. The milled fibers with an average fiber diameter of 1.6 ± 0.9 µm were continuously fed with a vibratory feeder into a twin-screw blender, which was integrated with a tableting machine to prepare tablets with ~ 10 kN compression force. The blend of fibers and excipients leaving the continuous blender was characterized with a bulk density of 0.43 g/cm³ and proved to be suitable for direct tablet compression. The ASD content, and thus the API content was determined in-line before tableting and at-line after tableting using near-infrared and Raman spectroscopy. The prepared tablets fulfilled the USP <905> content uniformity requirement based on the API content of ten randomly selected tablets. This work highlights that combining the advantages of electrospinning (e.g. less solvent, fast and gentle drying, low energy consumption, and amorphous products with high specific surface area) and the continuous technologies opens a new and effective way in the field of manufacturing of the poorly water-soluble APIs.

Effect Of Surfactant Chain Length On Emulsification Dynamics Of Self Emulsifying Formulation Of Poorly Soluble Drug

AIM

In this work the aim was to study the chain length of surfactant on the self emulsifying system of a poorly soluble drug, aceclofenac. The selection of almond oil as a lipid vehicle was done on basis of solubility and compatibility of the vehicle with the drug.

METHODS

The effect of varying chain length of different surfactants of Tween series namely Tween 20, Tween 40, Tween 60 and Tween 80 was evaluated on self emulsifying efficiency by constructing pseudoternary diagrams. PEG-400 was used as co-surfactant in a definite ratio with all the surfactants to minimize their concentration. The best self emulsifying ability was exhibited by Tween 80: PEG-400 combination followed by Tween 60: PEG-400, Tween 40: PEG-400, Tween 20: PEG-400. This observation indicates that as the chain length of Tweens increases their ability to form a good microemulsion increases if same co-surfactant is used.

RESULTS

However it has also been found that the presence of unsaturated bond in Tween 80 provides it an elasticity which supports good intermixing of oil and water and leading to formation of a fine microemulsion. Six different formulations were prepared using combination of almond oil, Tween 80, PEG-400 and the drug aceclofenac.

CONCLUSION

The formulations were subjected to various evaluation parameters such as dispersibility, transmittance, pH, globule size, polydispersibility, zeta potential, viscosity, refractive index and in vitro dissolution. The best formulation was found to have globule size of less than 100 nm, zeta potential of -3.35 ± 0.60 mV which indicates formation of a microemulsion of aceclofenac with good stability.

Formulation and Evaluation of Sustained Release Matrix Tablets of Aceclofenac

This study aimed to improve the dissolution rate of aceclofenac and release the drug in a controlled manner over a period of 24 hours. Matrix tablets were prepared by direct compression method, using hydrophilic polymers (HPMC/guar gum). Matrix tablets were prepared by wet granulation method using different hydrophilic polymers (HPMC/guar gum). Tablets were evaluated for in vitro drug release profile in phosphate buffer with pH 6.8 (without enzymes). The thickness and hardness of prepared tablets were 3.23 ± 0.035 to 3.28 ± 0.008 mm and 3.26 ± 0.115 to 3.60 ± 0.200 kg/cm2, respectively. The friability was within the acceptable limits of pharmacopoeial specifications (0.31 to 0.71%), which indicates the good mechanical strength of the tablets. Drug release was retarded with an increase in polymer concentration due to the gelling property of polymers. The in vitro drug release from the proposed system was best explained by Higuchi’s model, indicating that drug release from tablets displayed a diffusion-controlled mechanism. The results clearly indicate that guar gum could be a potential hydrophilic carrier in developing oral controlled drug delivery systems. Based on the study results, formulations F8 was selected as the best formulation.

In Vitro Drug Release, Permeability, and Structural Test of Ciprofloxacin-Loaded Nanofibers

Nanofibers of the poorly water-soluble antibiotic ciprofloxacin (CIP) were fabricated in the form of an amorphous solid dispersion by using poly(vinyl pyrrolidone) as a polymer matrix, by the low-cost electrospinning method. The solubility of the nanofibers as well as their in vitro diffusion were remarkably higher than those of the CIP powder or the physical mixture of the two components. The fiber size and morphology were optimized, and it was found that the addition of the CIP to the electrospinning solution decreased the nanofiber diameter, leading to an increased specific surface area. Structural characterization confirmed the interactions between the drug and the polymer and the amorphous state of CIP inside the nanofibers. Since the solubility of CIP is pH-dependent, the in vitro solubility and dissolution studies were executed at different pH levels. The nanofiber sample with the finest morphology demonstrated a significant increase in solubility both in water and pH 7.4 buffer. Single medium and two-stage biorelevant dissolution studies were performed, and the release mechanism was described by mathematical models. Besides, in vitro diffusion from pH 6.8 to pH 7.4 notably increased when compared with the pure drug and physical mixture. Ciprofloxacin-loaded poly(vinyl pyrrolidone) (PVP) nanofibers can be considered as fast-dissolving formulations with improved physicochemical properties.

Scale-up of Electrospinning: Market Overview of Products and Devices for Pharmaceutical and Biomedical Purposes

Recently, the electrospinning (ES) process has been extensively studied due to its potential applications in various fields, particularly pharmaceutical and biomedical purposes. The production rate using typical ES technology is usually around 0.01-1 g/h, which is lower than pharmaceutical industry production requirements. Therefore, different companies have worked to develop electrospinning equipment, technological solutions, and electrospun materials into large-scale production. Different approaches have been explored to scale-up the production mainly by increasing the nanofiber jet through multiple needles, free-surface technologies, and hybrid methods that use an additional energy source. Among them, needleless and centrifugal methods have gained the most attention and applications. Besides, the production rate reached (450 g/h in some cases) makes these methods feasible in the pharmaceutical industry. The present study overviews and compares the most recent ES approaches successfully developed for nanofibers' large-scale production and accompanying challenges with some examples of applied approaches in drug delivery systems. Besides, various types of commercial products and devices released to the markets have been mentioned.

Fast Dissolution Electrospun Medicated Nanofibers for Effective Delivery of Poorly Water-Soluble Drugs

BACKGROUND

Electrospinning is developing rapidly from an earlier laboratory method into an industrial process. The clinical applications are approached in various ways through electrospun medicated nanofibers. The fast-dissolving oral drug delivery system (DDS) among them is one of the most promising routes in the near future for commercial applications.

METHODS

Related papers are investigated, including the latest research results, on electrospun nanofiber-based fast-dissolution DDSs.

RESULTS

Several relative topics have been concluded: 1) the development of electrospinning, ranging from 1-fluid blending to multi-fluid process and potential applications in the formation of medicated nanofibers involving poorly water-soluble drugs; 2) Selection of appropriate polymer matrices and drug carriers for filament formation; 3) Types of poorly water-soluble drugs ideal for fast oral delivery; 4) The methods for evaluating fast-dissolving nanofibers; 5) The mechanisms that promote the fast dissolution of poorly water-soluble drugs by electrospun nanofibers; 6) the important issues for further development of electrospun medicated nanofibers as oral fast-dissolving drug delivery systems. Conclusions & Perspectives: The unique properties of electrospun-medicated nanofibers can be used as oral fast dissolving DDSs of poorly water-soluble drugs. However, some significant issues need to be investigated, such as scalable productions and solid dosage form conversions.

Core-Shell Eudragit S100 Nanofibers Prepared via Triaxial Electrospinning to Provide a Colon-Targeted Extended Drug Release

In this study, a new modified triaxial electrospinning is implemented to generate an Eudragit S100 (ES100)-based core-shell structural nanofiber (CSF), which is loaded with aspirin. The CSFs have a straight line morphology with a smooth surface, an estimated average diameter of 740 ± 110 nm, and a clear core-shell structure with a shell thickness of 65 nm, as disclosed by the scanning electron microscopy and transmission electron microscopy results. Compared to the monolithic composite nanofibers (MCFs) produced using traditional blended single-fluid electrospinning, aspirin presented in both of them amorously owing to their good compatibility. The CSFs showed considerable advantages over the MCFs in providing the desired drug-controlled-release profiles, although both of them released the drug in an erosion mechanism. The former furnished a longer time period of time-delayed-release and a smaller portion released during the first two-hour acid condition for protecting the stomach membranes, and also showed a longer time period of aspirin-extended-release for avoiding possible drug overdose. The present protocols provide a polymer-based process-nanostructure-performance relationship to optimize the reasonable delivery of aspirin.

Microstructure of Ni0.5Zn0.5Fe2O4 Nanofiber with Metal Nitrates in Electrospinning Precursor

Electrospun NiZn ferrite nanofibers have great potential due to their one-dimensional structure and electrical properties, but they have a low reproducibility resulting from many process confounders, so much research effort is needed to achieve optimized process control. For structure control, the viscosity of the precursor solution is a likely parameter. One solution is to use polyvinyl pyrrolidone (PVP) and metal nitrate to obtain the desired viscosity by increasing the nitrate content, even if the polymer content is decreased. Ni_0.5Zn_0.5Fe₂O₄ ferrite nanofiber was electrospun with various precursor conditions. Fifteen different precursor solutions, with a content of five polymers and three metal nitrates, were prepared, with precursor solutions composed of Fe(NO₃)₂·9H₂O, Ni(NO₃)₂·6H₂O, Zn(NO₃)₂·6H₂O, polyvinyl pyrrolidone (PVP), and N,N-dimethylmethanamide. The fiber diameter changed from the lowest, of 62.41 nm, to 417.54 nm. This study shows that the average diameter can be controlled using the metal nitrate concentration without a difference in crystal structure when PVP is used. In a 24.0 mmol metal nitrate precursor solution, the process yield was improved to 140% after heat treatment. There was also no significant difference in the crystal structure and morphology. This system reduces the cost of raw materials for electrospinning and increases the process yield of NiZn ferrite nanofibers.

Preparation and Characterization of Fenofibrate-Loaded PVP Electrospun Microfibrous Sheets

Fenofibrate-loaded electrospun microfibrous sheets were prepared in an attempt to enhance the dissolution of the poorly soluble antihyperlipidemic agent and to improve its bioavailability. Physicochemical changes that appeared during the electrospinning process were monitored using a wide array of solid-state characterization techniques, including attenuated total reflectance Fourier-transformed infrared spectroscopy and positron annihilation lifetime spectroscopy, while fiber morphology was monitored via scanning electron microscopy. Dissolution studies carried out both in 0.025 M sodium dodecyl sulfate and in water revealed an immediate release of the active agent, with an approximately 40-fold release rate enhancement in water when compared to the micronized active agent. The dramatic increase in dissolution was attributed partially to the amorphous form of the originally crystalline active agent and the rapid disintegration of the electrospun microfibrous sheet due to its high surface area and porosity. The obtained results could pave the way for a formulation of the frequently used antihyperlipidemic agent with increased bioavailability.

Human mouthfeel panel investigating the acceptability of electrospun and solvent cast orodispersible films

A human panel study was performed to investigate the acceptability of orodispersible electrospun and solvent cast films. 50 healthy volunteers took two drug-free samples of polyvinyl alcohol films prepared by the two methods. On a 5-point hedonic scale, the volunteers assessed the films' perceived size, stickiness, thickness, disintegration time, thickening effect on saliva, and handling. The films manufactured by both methods were similar in their end-user acceptability. The modal values of perceived size, thickness, disintegration time, saliva thickening effect, and handling were high (4 or 5). However, for both, the stickiness mode was 2 (strongly sticky) and the only negative attribute. Both films were reported to take approximately 30 s to disintegrate completely in the mouth. Electrospun films scored similarly high to solvent cast orodispersible films in most attributes of end-user acceptability. Electrospun films were marginally preferred, with 27 out of 50 participants picking electrospinning when presented with a forced choice test of both fabrication methods. This is the first study to show that electrospinning enables the fabrication of orodispersible films that are acceptable to adult human participants in terms of handling and mouthfeel and suggests that the potential for clinical translation of such formulations is high.

Development of ferulic acid/cyclodextrin inclusion complex nanofibers for fast-dissolving drug delivery system

Production of electrospun nanofibrous mats of cyclodextrin inclusion complexes with the incorporation of drug molecules would enable promising designing of fast dissolving delivery systems (FDDS) for oral treatments. Here, the single-step electrospinning technique has been applied to prepare cyclodextrin inclusion complex nanofibrous mats (CD-IC NM) of ferulic acid from complete aqueous systems without using any polymeric matrix. The free-standing ferulic acid/CD-IC NM have been electrospun from two different modified cyclodextrin derivatives of hydroxypropyl-beta-cyclodextrin (HP-β-CD) and hydroxypropyl-gamma-cyclodextrin (HP-γ-CD). The initial content of ferulic acid (1/1 ferulic acid/CD (molar ratio) and ~11% (w/w)) has been protected in case of both ferulic acid/CD-IC NM and so the electrospun nanofibrous mats have been fabricated by the ~100% loading efficiency. It has been detected from the in vitro release and disintegration tests that, the amorphous state of ferulic acid based on inclusion complex formation, and the highly porous feature and high surface area of nanofibrous mats have ensured the fast dissolution/release of ferulic acid and disintegration of nanofibrous mats into the liquid medium and artificial saliva. Herein, HP-γ-CD has formed inclusion complexes with ferulic acid more favorably than HP-β-CD and this has leaded to the existence of some un-complexed ferulic acid crystals in ferulic acid/HP-β-CD-IC NM while, ferulic acid has been completely complexed and is in amorphous state in ferulic acid/HP-γ-CD-IC NM. Furthermore, the thermal stability of ferulic acid has been enhanced as an inclusion complexation aid observed by the shift of thermal degradation temperature of ferulic acid from the range of ~120-200 °C to ~140-280 °C.

Recent Development of Electrospinning for Drug Delivery

Electrospinning is one of the most widely used techniques for the fabrication of nano/microparticles and nano/microfibers, induced by a high voltage applied to the drug-loaded solution [...].