Formulation Composition and Process Affect Counterion for CSP7 Peptide

Identification of Stability Constraints in the Particle Engineering of an Inhaled Monoclonal Antibody Dried Powder

Monoclonal antibody (mAb) based therapies may provide a valuable new treatment modality for acute and chronic lung diseases, including asthma, respiratory infections, and lung cancer. Currently mAbs are delivered via systemic administration routes, but direct delivery to the lungs via the inhaled route could provide higher concentrations at the site of disease and reduced off-target effects. Though lyophilized mAbs may be reconstituted and delivered to the lungs using nebulizers, dry powder inhalers provide a more patient-friendly delivery method based upon their fast administration time and portability. However, particle engineering processes required to prepare respirable dried powders for DPI delivery involve multiple potential stressors for mAbs, which have not been fully explored. In this study, a systematic examination of various aspects of the particle engineering process (atomization, freezing, drying, and storage) was performed to further understand their impact on mAb structure and aggregation. Using anti-streptavidin IgG1 as a model mAb, atomization settings were optimized using a design of experiments approach to elucidate the relationship between feed flow rate, formulation solid content, and atomization airflow rate and protein structural changes and aggregation. The optimized atomization conditions were then applied to spray drying and spray freezing drying particle engineering processes to determine the effects of freezing and drying on IgG1 stability and aerosol performance of the powders. IgG1 was found to be particularly susceptible to degradation induced by the expansive air-ice interface generated by spray freeze drying and this process also produced powders that exhibited decreased storage stability. This study further delineates the design space for manufacturing of respirable biologic therapies and is intended to serve as a roadmap for future development work.

Therapeutic peptides for chemotherapy: Trends and challenges for advanced delivery systems

The past decades witnessed an increasing interest in peptides as clinical therapeutics. Rightfully considered as a potential alternative for small molecule therapy, these remarkable pharmaceuticals can be structurally fine-tuned to impact properties such as high target affinity, selectivity, low immunogenicity along with satisfactory tissue penetration. Although physicochemical and pharmacokinetic challenges have mitigated, to some extent, the clinical applications of therapeutic peptides, their potential impact on modern healthcare remains encouraging. According to recent reports, there are more than 400 peptides under clinical trials and 60 were already approved for clinical use. As the demand for efficient and safer therapy became high, especially for cancers, peptides have shown some exciting developments not only due to their potent antiproliferative action but also when used as adjuvant therapies, either to decrease side effects with tumor-targeted therapy or to enhance the activity of anticancer drugs via transbarrier delivery. The first part of the present review gives an insight into challenges related to peptide product development. Both molecular and formulation approaches intended to optimize peptide's pharmaceutical properties are covered, and some of their current issues are highlighted. The second part offers a comprehensive overview of the emerging applications of therapeutic peptides in chemotherapy from bioconjugates to nanovectorized therapeutics.

Influence of Carbamazepine Dihydrate on the Preparation of Amorphous Solid Dispersions by Hot Melt Extrusion

Amorphous solid dispersions (ASDs) are commonly used in the pharmaceutical industry to improve the dissolution and bioavailability of poorly water-soluble drugs. Hot melt extrusion (HME) has been employed to prepare ASD based products. However, due to the narrow processing window of HME, ASDs are normally obtained with high processing temperatures and mechanical stress. Interestingly, one-third of pharmaceutical compounds reportedly exist in hydrate forms. In this study, we selected carbamazepine (CBZ) dihydrate to investigate its solid-state changes during the dehydration process and the impact of the dehydration on the preparation of CBZ ASDs using a Leistritz micro-18 extruder. Various characterization techniques were used to study the dehydration kinetics of CBZ dihydrate under different conditions. We designed the extrusion runs and demonstrated that: 1) the dehydration of CBZ dihydrate resulted in a disordered state of the drug molecule; 2) the resulted higher energy state CBZ facilitated the drug solubilization and mixing with the polymer matrix during the HME process, which significantly decreased the required extrusion temperature from 140 to 60 °C for CBZ ASDs manufacturing compared to directly processing anhydrous crystalline CBZ. This work illustrated that the proper utilization of drug hydrates can significantly improve the processability of HME for preparing ASDs.