Physical-Chemical Aspects of the Preparation and Drug Release of Electrospun Scaffolds

Encapsulation of a drug into electrospun fibers spun from water soluble polymers to control solubility and release

Electrospun fibers prepared from water-soluble polymers (PVP, PVA, and HPMC) were loaded with pregabalin, a BCS I drug, to address its fast release and adverse effects. The drug dissolved partially (1.8-2.8 wt%) in the polymers, with excess pregabalin in crystalline form within the fibers. The solubility of the drug varied with the pH of the dissolution medium. Most of the drug encapsulated into the fibers during electrospinning, but some was lost due to technical reasons. PVP showed no impact on drug release, offering no benefit as a carrier. However, PVA-based fibers exhibited considerably slower release than the dissolution rate of the neat drug and also the release rate from fibers prepared from the other polymers. This indicates the potential of PVA for using it with pregabalin in practical drug formulations with improved release properties. The pH of the dissolution medium influenced solubility and release rate for specific polymers. Overall, the study highlights the importance of polymer selection and pH control in optimizing the release profile of pregabalin in enhanced drug delivery.

Factorial design of in situ gelling two-compartment systems containing chlorhexidine for the treatment of periodontitis

Periodontitis is one of the most widespread bacterial infectious oral diseases that affects a significant percentage of the population worldwide. Different bacterial strains are responsible for the chronic inflammation and subgingival plaque that could be effectively treated with prolonged exposure to therapeutic levels of antibiotics and antiseptics in the periodontal pockets. Medicated in situ gels of chlorhexidine (CHX), for extended drug release and long-lasting antiseptic effect in the targeted cavities, were prepared in a two-compartment system. One compartment was loaded with sodium alginate solution while other was filled with CHX and calcium solution. The mixing of the solutions during the application resulted in gelation. Two 33 full factorial designs were applied in this study in order to optimize the gel formulation. Initially, the effects of concentration of gelling agent, crosslinker, and pH of the system on the dependent variables such as gel formation and structure characteristics were investigated. Then, the concentration of the crosslinker was optimized. Afterwards, the effect of gelling agent, loading of the drug, and pH of the gel system were correlated with the gel characteristics through another factorial design. Optimized formulations were tested for mucoadhesion, in vitro drug release, and microbiological investigation. Based on the results of the factorial design, mucoadhesiveness, antimicrobial investigation, and drug release, a 4 % alginate composition can be considered optimal. Overall, the optimized in situ periodontal gel was found to be effective with prolonged retention time and desirable outcomes.

Levocetirizine-Loaded Electrospun Fibers from Water-Soluble Polymers: Encapsulation and Drug Release

Electrospun fibers containing levocetirizine, a BCS III drug, were prepared from three water-soluble polymers, hydroxypropyl methylcellulose (HPMC), polyvinylpyrrolidone (PVP) and polyvinyl alcohol (PVA). Fiber-spinning technology was optimized for each polymer separately. The polymers contained 10 wt% of the active component. An amorphous drug was homogeneously distributed within the fibers. The solubility of the drug in the polymers used was limited, with a maximum of 2.0 wt%, but it was very large in most of the solvents used for fiber spinning and in the dissolution media. The thickness of the fibers was uniform and the presence of the drug basically did not influence it at all. The fiber diameters were in the same range, although somewhat thinner fibers could be prepared from PVA than from the other two polymers. The results showed that the drug was amorphous in the fibers. Most of the drug was located within the fibers, probably as a separate phase; the encapsulation efficiency proved to be 80-90%. The kinetics of the drug release were evaluated quantitatively by the Noyes-Whitney model. The released drug was approximately the same for all the polymers under all conditions (pH), and it changed somewhere between 80 and 100%. The release rate depended both on the type of polymer and pH and varied between 0.1 and 0.9 min^-1. Consequently, the selection of the carrier polymer allowed for the adjustment of the release rate according to the requirements, thus justifying the use of electrospun fibers as carrier materials for levocetirizine.

Improved Release of a Drug with Poor Water Solubility by Using Electrospun Water-Soluble Polymers as Carriers

In an attempt to improve the solubility of valsartan, a BCS II drug, fibers containing the drug were prepared from three water-soluble polymers, hydroxypropyl-methyl-cellulose (HPMC), polyvinyl-pyrrolidone (PVP), and polyvinyl-alcohol (PVA). Fiber spinning technology was optimized for each polymer separately. The polymers contained 20 wt% of the active component. The drug was homogenously distributed within the fibers in the amorphous form. The presence of the drug interfered with the spinning process only slightly, the diameters of the fibers were in the same range as without the drug for the HPMC and the PVA fibers, while it doubled in PVP. The incorporation of the drug into the fibers increased its solubility in all cases compared to that of the neat drug. The solubility of the drug itself depends very much on pH and this sensitivity remained the same in the HPMC and PVP fibers; the release of the drug is dominated by the dissolution behavior of valsartan itself. On the other hand, solubility and the rate of release were practically independent of pH in the PVA fibers. The different behavior is explained by the rate of the dissolution of the respective polymer, which is larger for HPMC and PVP, and smaller for PVA than the dissolution rate of the drug. The larger extent of release compared to neat valsartan can be explained by the lack of crystallinity of the drug, its better dispersion, and the larger surface area of the fibers. Considering all facts, the preparation of electrospun devices from valsartan and water-soluble polymers is beneficial, and the use of PVA is more advantageous than that of the other two polymers.