A Novel Synthetic Strategy for Preparing Polyamide 6 (PA6)-Based Polymer with Transesterification

Nude and Modified Electrospun Nanofibers, Application to Air Purification

Air transports several pollutants, including particulate matter (PM), which can produce cardiovascular and respiratory diseases. Thus, it is a challenge to control pollutant emissions before releasing them to the environment. Until now, filtration has been the most efficient processes for removing PM. Therefore, the electrospinning procedure has been applied to obtain membranes with a high filtration efficiency and low pressure drop. This review addressed the synthesis of polymers that are used for fabricating high-performance membranes by electrospinning to remove air pollutants. Then, the most influential parameters to produce electrospun membranes are indicated. The main results show that electrospun membranes are an excellent alternative to having air filters due to the versatility of the process, the capacity for controlling the fiber diameter, porosity, high filtration efficiency and low-pressure drop.

Assessing the Conversion of Various Nylon Polymers in the Hydrothermal Liquefaction of Macroalgae

Marine macroalgae offers a promising third generation feedstock for the production of fuels and chemicals, avoiding competition with conventional agriculture and potentially helping to improve eutrophication in seas and oceans. However, an increasing amount of plastic is distributed into the oceans, and as such contaminating macroalgal beds. One of the major plastic contaminants is nylon 6 derived from discarded fishing gear, though an increasing amount of alternative nylon polymers, derived from fabrics, are also observed. This study aimed to assess the effect of these nylon contaminants on the hydrothermal liquefaction of Fucus serratus. The hydrothermal liquefaction (HTL) of macroalgae was undertaken at 350 °C for 10 min, with a range of nylon polymers (nylon 6, nylon 6/6, nylon 12 and nylon 6/12), in the blend of 5, 20 and 50 wt.% nylon to biomass; 17 wt.% biocrude was achieved from a 50% blend of nylon 6 with F. serratus. In addition, nylon 6 completely broke down in the system producing the monomer caprolactam. The suitability of converting fishing gear was further demonstrated by conversion of actual fishing line (nylon 6) with the macroalgae, producing an array of products. The alternative nylon polymer blends were less reactive, with only 54% of the nylon 6/6 breaking down under the HTL conditions, forming cyclopentanone which distributed into the biocrude phase. Nylon 6/12 and nylon 12 were even less reactive, and only traces of the monomer cyclododecanone were observed in the biocrude phase. This study demonstrates that while nylon 6 derived from fishing gear can be effectively integrated into a macroalgal biorefinery, alternative nylon polymers from other sectors are too stable to be converted under these conditions and present a real challenge to a macroalgal biorefinery.

Microplastic fibres from synthetic textiles: Environmental degradation and additive chemical content

Microplastic fibres (MPFs) often make up the largest fraction of microplastic pollution in aquatic environments, yet little is known about their degradative fate and persistence. This study investigates the environmentally relevant photodegradation of common MPFs: polyester (PET), polyamide (PA) and polyacrylonitrile (PAN), their respective additive chemical profile, together with their potential for additive leaching. MPFs were subject to ultraviolet (UV) exposure in seawater and freshwater media over 10 months. PET and PA MPFs showed significant fragmentation and surface changes following UV exposure, additionally PA showed evidence of chemical changes. PAN did not undergo significant photodegradation in the same exposure period. Chemicals tentatively identified in MPFs and aqueous leachates via non-target gas chromatography-mass spectrometry include monomers, UV stabilisers and degradation products. Characterisation of several bisphenols (BPs) and benzophenones (BzPs) was performed via ultraperformance liquid chromatography tandem mass spectrometry. Bisphenol A, bisphenol S and benzophenone-3 were quantified in all MPFs and wool at concentrations between 4.3 and 501 ng/g, with wool displaying the highest sum concentration of BPs and BzPs at 863 and 27 ng/g, respectively.

Effect of Composition on the Crystallization, Water Absorption, and Biodegradation of Poly(ε-caprolactam-co-ε-caprolactone) Copolymers

Poly(ester amide)s have aroused extensive research interest due to the combination of the degradability of polyester and the higher mechanical properties of polyamide. In this work, a series of poly(ε-caprolactam-co-ε-caprolactone) (P(CLA-co-CLO)) copolymers with different compositions were synthesized by anionic copolymerization. The structure, crystallization behavior, water absorption, and biodegradation behavior of these copolymers were investigated by means of nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), and polarized optical micrographs (POM). The results indicated that the composition of P(CLA-co-CLO) copolymers can be adjusted by the molar feed ratio. The PCL blocks decreased the crystallization rate of PA6 blocks but had little effect on the melting behavior of PA6, while the crystallized PA6 acted as a heterogeneous nucleating agent and greatly improved the crystallization rate of PCL. Moreover, the introduction of PCL blocks greatly reduced the water absorption of P(CLA-co-CLO) copolymers and endow them a certain degree of degradability.