Plasticization of Polylactide after Solidification: An Effectiveness and Utilization for Correct Interpretation of Thermal Properties

Mechanical and morphological properties of cellulose biocomposites

Natural biocomposites offer promising alternatives to petroleum-based composites thanks to their biocompatibility, sustainability, and low environmental impact. However, they must also demonstrate competitive mechanical properties and adaptability to manufacturing processes. To this end, we developed cellulosic biocomposites using plasticized cellulose acetate (PCA) reinforced with cellulosic fibers at loadings from 30 to 50 wt%. Mechanical properties were determined with tensile, bending, and impact tests and interfacial bonding was analyzed using scanning electron microscopy (SEM). Results showed that the adhesion of 50 wt% cellulose fibers increased the Young's modulus of the biocomposites by 300 % and the tensile strength by 12 %. Flexural properties also improved: the flexural modulus increased from 1.52 GPa to 5 GPa for PCA at maximum fiber loading, and from 43.3 MPa to 54 MPa for flexural strength. However, the elongation at break decreased with increasing cellulose content, from 13.5 % to 0.8 %, along with a 74 % decrease in impact strength. SEM results revealed good fiber dispersion, interfacial adhesion, porosity, and fiber pullout. These results underscore the potential for cellulose biocomposites as eco-friendly alternatives for high-value utilizations, including electronic and dielectric applications.

Optimization of the ductile properties of poly(lactic acid) (PLA) using green citrate-based plasticizers and itaconic anhydride grafted PLA (PLA-g-IA)

Certain miscellaneous beans have a low glycemic index (GI) and may reduce the risk of chronic metabolic disorders, including type 2 diabetes and obesity, by modulating postprandial glucose homeostasis and blood lipid levels. In this study, red kidney bean flour and wheat gluten were used as raw materials, and long-chain inulin phosphate monoester (PFXL) was added to improve the quality of red kidney bean dough, prepare high-quality steamed bread, and explore its health effect on type 2 diabetes. The results showed that the addition of PFXL improved the water distribution and rheological properties of coarse grain dough and enriched the flavor of coarse grain steamed bread. In addition, the optimized steamed bread exhibited a low glycemic index (eGI = 51.76), which could reduce fasting blood glucose and glycated serum protein by 21.55 % and 26.11 %, respectively, and could significantly improve oral glucose tolerance and blood lipid levels in diabetic mice and had a certain protective effect on liver injury. Overall, these findings provide a scientific basis for the development of functional foods.

Strain Rate and Temperature Influence on Micromechanisms of Plastic Deformation of Polyethylenes Investigated by Positron Annihilation Lifetime Spectroscopy

Plastic deformation of low/high density polyethylene (LDPE/HDPE) was analyzed in this work using positron annihilation lifetime spectroscopy (PALS). It was shown that in undeformed LDPE, both the mean ortho-positronium lifetime (τ3) and its dispersion (σ3), corresponding to the average size and size distribution of the free-volume pores of the amorphous component, respectively, were clearly higher than in HDPE. This effect was induced by a lower and less uniform molecular packing of the amorphous regions in LDPE. During the deformation of LDPE, an increase in the τ3 value was observed within the local strains of 0-0.25. This effect was mainly stimulated by a positive relative increase in interlamellar distances due to the deformation of lamellar crystals oriented perpendicular (increased by 31.8%) and parallel (decreased by 10.1%) to the deformation directions. At the same time, the dimension of free-volume pores became more uniform, which was manifested by a decrease in the σ3 value. No significant effect of temperature or strain rate on the τ3 and σ3 values was observed during LDPE deformation. In turn, in the case of HDPE, with an increase in the strain rate/or a decrease in temperature, an intensification of the cavitation phenomenon could be observed with a simultaneous decrease in the τ3 value. This effect was caused by the lack of annihilation of ortho-positonium (o-Ps) along the longer axis of the highly anisotropic/ellipsoidal cavities. Therefore, this dimension was not detectable by the PALS technique. At the same time, the increase in the dimension of the shorter axis of the cavities was effectively limited by the thickness of amorphous layers. As the strain rate increased or the temperature decreased, the σ3 value during HDPE deformation increased. This change was correlated with the initiation and intensification of the cavitation phenomenon. Based on the mechanical response of samples with a similar yield stress, it was also proven that the susceptibility of the amorphous regions of LDPE to the formation of cavities is lower than in the case of amorphous component of HDPE.

Diminishment the gas permeability of polyethylene by "densification" of the amorphous regions

High-density polyethylene/paraffin wax (HDPE/wax) systems with adjustable density of the amorphous regions were prepared by a melt-blending process to optimize/control the final oxygen barrier properties. The introduction of paraffin wax (a low molecular weight modifier) is the key to tune the gas permeability properties of polyethylene-based materials. Density gradient column (DGC) measurements distinctly showed that the incorporation of modifier led to densification of the amorphous phase of semicrystalline HDPE consisting in a decrease in the average fractional free volume confirmed by positron annihilation lifetime spectroscopy (PALS). Polyethylene with "densified" amorphous phase exhibits lower oxygen permeability parameters compared to pristine polyethylene, but it is characterized by similar thermal and thermomechanical properties. An increase in the density of the amorphous regions of polyethylene by about 0.003 g/cm3, which corresponds to 0.3%, reduces the permeability of oxygen by up to 22%. For the first time, it has been proven that by controlling the density of the amorphous regions of semicrystalline polymers, it is possible to obtain materials with appropriate transport properties (without changing other properties) for applications meeting specific requirements.

Tailoring and Long-Term Preservation of the Properties of PLA Composites with "Green" Plasticizers

Concerning new polylactide (PLA) applications, the study investigates the toughening of PLA-CaSO4 β-anhydrite II (AII) composites with bio-sourced tributyl citrate (TBC). The effects of 5-20 wt.% TBC were evaluated in terms of morphology, mechanical and thermal properties, focusing on the enhancement of PLA crystallization and modification of glass transition temperature (Tg). Due to the strong plasticizing effects of TBC (even at 10%), the plasticized composites are characterized by significant decrease of Tg and rigidity, increase of ductility and impact resistance. Correlated with the amounts of plasticizer, a dramatic drop in melt viscosity is also revealed. Therefore, for applications requiring increased viscosity and enhanced melt strength (extrusion, thermoforming), the reactive modification, with up to 1% epoxy functional styrene-acrylic oligomers, was explored to enhance their rheology. Moreover, larger quantities of products were obtained by reactive extrusion (REX) and characterized to evidence their lower stiffness, enhanced ductility, and toughness. In current prospects, selected samples were tested for the extrusion of tubes (straws) and films. The migration of plasticizer was not noted (at 10% TBC), whereas the mechanical and thermal characterizations of films after two years of aging evidenced a surprising preservation of properties.

Novel Poly(Methylenelactide-g-L-Lactide) Graft Copolymers Synthesized by a Combination of Vinyl Addition and Ring-Opening Polymerizations

In this work, a novel poly (methylenelactide-g-L-lactide), P(MLA-g-LLA) graft copolymer was synthesized from poly(methylenelactide) (PMLA) and L-lactide (LLA) using 0.03 mol% liquid tin(II) n-butoxide (Sn(OnBu)2) as an initiator by a combination of vinyl addition and ring-opening polymerization (ROP) at 120 °C for 72 h. Proton and carbon-13 nuclear magnetic resonance spectroscopy (1H- and 13C-NMR) and Fourier-transform infrared spectroscopy (FT-IR) confirmed the grafted structure of P(MLA-g-LLA). The P(MLA-g-LLA) melting temperatures (Tm) range of 144-164 °C, which was lower than that of PLA (170-180 °C), while the thermal decomposition temperature (Td) of around 314-335 °C was higher than that of PLA (approx. 300 °C). These results indicated that the grafting reaction could widen the melt processing range of PLA and in doing so increase PLA's thermal stability during melt processing. The graft copolymers were obtained with weight-average molecular weights (M¯w) = 4200-11,000 g mol-1 and a narrow dispersity (Đ = 1.1-1.4).

The Effect of WS2 Nanosheets on the Non-Isothermal Cold- and Melt-Crystallization Kinetics of Poly(l-lactic acid) Nanocomposites

In the present work, hybrid nanocomposite materials were obtained by a solution blending of poly(l-lactic acid) (PLLA) and layered transition-metal dichalcogenides (TMDCs) based on tungsten disulfide nanosheets (2D-WS2) as a filler, varying its content between 0 and 1 wt%. The non-isothermal cold- and melt-crystallization and melting behavior of PLLA/2D-WS2 were investigated. The overall crystallization rate, final crystallinity, and subsequent melting behavior of PLLA were controlled by both the incorporation of 2D-WS2 and variation of the cooling/heating rates. In particular, the analysis of the cold-crystallization behavior of the PLLA matrix showed that the crystallization rate of PLLA was reduced after nanosheet incorporation. Unexpectedly for polymer nanocomposites, a drastic change from retardation to promotion of crystallization was observed with increasing the nanosheet content, while the melt-crystallization mechanism of PLLA remained unchanged. On the other hand, the double-melting peaks, mainly derived from melting-recrystallization-melting processes upon heating, and their dynamic behavior were coherent with the effect of 2D-WS2 involved in the crystallization of PLLA. Therefore, the results of the present study offer a new perspective for the potential of PLLA/hybrid nanocomposites in targeted applications.

Nanocomposite Materials with Poly(l-lactic Acid) and Transition-Metal Dichalcogenide Nanosheets 2D-TMDCs WS2

Layered transition-metal dichalcogenides (TMDCs) based on tungsten disulfide nanosheets (2D-WS2) were introduced via melt processing into poly(l-lactic acid) (PLLA) to generate PLLA/2D-WS2 nanocomposite materials. The effects of the 2D-WS2 on the morphology, crystallization, and biodegradation behavior of PLLA were investigated. In particular, the non-isothermal melt-crystallization of neat PLLA and PLLA/2D-WS2 nanocomposites were analyzed in detail by varying both the cooling rate and 2D-WS2 loading. The kinetic parameters of PLLA chain crystallization are successfully described using the Liu model. It was found that the PLLA crystallization rate was reduced with 2D-WS2 incorporation, while the crystallization mechanism and crystal structure of PLLA remained unchanged in spite of nanoparticle loading. This was due to the PLLA chains not being able to easily adsorb on the WS2 nanosheets, hindering crystal growth. In addition, from surface morphology analysis, it was observed that the addition of 2D-WS2 facilitated the enzymatic degradation of poorly biodegradable PLLA using a promising strain of actinobacteria, Lentzea waywayandensis. The identification of more suitable enzymes to break down PLLA nanocomposites will open up new avenues of investigation and development, and it will also lead to more environmentally friendly, safer, and economic routes for bioplastic waste management.