Biodegradation of Poly(Lactic Acid) Biocomposites under Controlled Composting Conditions and Freshwater Biotope

"Flexible-strong" polylactic acid porous membrane via tailored polymerization degree of lactic acid side-chains grafting for passive daytime radiative cooler

Aerogel possesses the advantages of high specific surface area, low density, and high porosity, which have shown great application in thermal regulation due to its efficient light scattering capability. However, traditional polymer-based aerogels have poor mechanical properties and lack ductility in outdoor applications, the cooling efficiency of the material is easily affected by damage during transportation, installation, and environmental factors. In this work, combining the porous nature of aerogels and the high ductility of membranes, a polylactic acid-based porous membrane cooler was developed by combining a regular honeycomb surface porous structure design and physical/chemical modification to enhance flexibility, using a simple non-solvent induced phase separation method. This porous membrane exhibits both super-flexibility (116 % elongation at break) and porous characteristics. It achieves a sub-ambient temperature decrease of 4-6 °C under direct sunlight. The optimized porous membrane demonstrates high solar reflectance (94 % of peak reflectivity, 90 % of average reflectivity) and strong infrared emissivity (96 % of peak emissivity, 91 % of average emissivity), it also maintains a solar peak reflectivity of 91 % under 100 % tensile strain and 1000 bending cycles, the cooler still maintains a cooling effect of 2-5 °C below ambient temperature. This work paves the way for developing mechanical flexible and strong radiative coolers for thermal regulation.

Effects of turning aeration and the initial carbon/nitrogen ratio on the biodegradation of polylactic acid under controlled conditions

Plastic pollution is primarily caused by the accumulation of petroleum-derived plastics, as they tend to degrade slowly. Sustainable alternatives to these materials are bio-based and biodegradable plastics, such as polylactic acid (PLA). In this study, we assessed how turning aeration and the initial carbon/nitrogen (C/N) ratio impact PLA biodegradation. The study was carried out under controlled composting conditions, over 180 days, with the aim of decreasing the biodegradation time of the PLA. Apple pomace, rice husk, grape pomace compost, and PLA were used as substrates in the composting process. The experiments were conducted using three types of turning aeration: without turning, one turn per week, and two turns per week. Three initial C/N ratios were used: 20, 30, and 40. A stepwise temperature ramp was designed and implemented to simulate industrial composting conditions, which influence microbial activity and thus the rate of decomposition of substrates, including PLA. The data showed behavior; hence, a nonlinear regression model based on the logistic growth equation was used to predict the PLA biodegradation at the end of the composting process. The results showed that two turns per week with an initial C/N ratio of 30 or 40 led to a 90 % biodegradation of the PLA in 130 days. This degradation was verified by Fourier-Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM).

Effect of the addition of biochar and wood vinegar on the morphology of heavy metals in composts

In the experiment, the morphology of heavy metals (Pb, Cr, Cd, and Ni, HMs) was characterized using flame atomic absorption spectroscopy. In addition, Fourier transform infrared spectroscopy (FTIR) and three-dimensional excitation-emission matrix fluorescence spectroscopy (3D-EEM) were used to characterize the correlation between environmental factors and metal morphology in the rotting compost from several angles. The results showed that the humus treated with wood vinegar solution had a high degree of humification and rich aromatic structure. FTIR spectroscopy confirmed that the degree of humus aromatization gradually increased during the composting process, which enhanced the complexation of humus (HS) with HMs but had less effect on Ni. In addition, the optimum concentration of wood vinegar (WV) was determined to be 1.75%. The results of the study showed that in the Pb passivation treatment group, the proportion of soluble (Red) and exchangeable states (Exc) converted to oxidized (Oxi) and residual states (Res) was 8%, 14%, 6%, 1%, and 12% in the CK, T1, T2, T3, and T4 treatment groups, respectively; in the Cr passivation treatment group, the proportion of Cr-Red and Cr-Exc converted to oxidized and residual states was 31%, 33%, 25%, 29%, and 25%; in the Cd passivation treatment group, the proportions of Cd-Red and Cd-Exc converted to oxidized and residual states were 5%, 15%, 4%, 9%, and 11%, respectively; whereas the Ni treatment group did not show any significant passivation effect. The proportion of Pb-Oxi was relatively stable, Cr-Oxi was converted to Cr-Res, whereas Cd showed the conversion of Cd-Oxi to Cd-Exc. SUVA254 and SUVA280 showed significant positive correlations with Pb-Res, Cr-Res and Ni-Res, and significant positive correlations with moisture content (MC); whereas MC was significantly negatively correlated with each form of HMs. Total potassium (TK), total nitrogen (TN), and both carbon (TOC) were negatively correlated with Pb-Res and Pb-Exc. Structural equation modeling verified the relationship between environmental factors and HMs, and the composting results showed that the addition of biochar (BC) and a higher percentage of WV could increase compost decomposition and passivate HMs to improve its agronomic function.

Toward the Improvement of Maleic Anhydride Functionalization in Polyhydroxybutyrate (PHB): Effect of Styrene Monomer and Sn(Oct)2 Catalyst

In this work, polyhydroxybutyrate (PHB) was maleic anhydride (MA)-grafted in the molten state, using dicumyl peroxide (DCP) as a reaction initiator. Tin(II) 2-ethylhexanoate (Sn(Oct)2) and styrene monomer (St.) were used to maximize the maleic anhydride grafting degree. When PHB was modified with MA/DCP and MA/DCP/Sn(Oct)2, viscosity was reduced, suggesting chain scission in relation to pure PHB. However, when the styrene monomer was added, the viscosity increased due to multiple grafts of MA and styrene into the PHB chain. In addition, the FTIR showed the formation of a new band at 1780 cm-1 and 704 cm-1, suggesting a multiphase copolymer PHB-g-(St-co-MA). The PHB (MA/DCP) system showed a grafting degree of 0.23%; however, the value increased to 0.39% with incorporating Sn(Oct)2. The highest grafting efficiency was for the PHB (MA/DCP/St.) system with a value of 0.91%, while the PHB (MA/DCP/St./Sn(Oct)2) hybrid mixture was reduced to 0.73%. The chemical modification process of PHB with maleic anhydride increased the thermal stability by about 20 °C compared with pure PHB. The incorporation of 0.5 phr of the Sn(Oct)2 catalyst increased the efficiency of the grafting degree in the PHB. However, the St./Sn(Oct)2 hybrid mixture caused a deleterious effect on the maleic anhydride grafting degree.

Degradation of Polylactic Acid Polymer and Biocomposites Exposed to Controlled Climatic Ageing: Mechanical and Thermal Properties and Structure

This paper deals with the study of the degradation of polylactic acid (PLA) material structures and biocomposite systems with a PLA matrix containing ground natural particulate waste fillers, buckwheat husks and egg shells. Waste fillers were used without difficult cleaning operations to describe the effect of the raw waste material on PLA. Biocomposites with raw waste materials are increasingly coming to the forefront in car interiors and packaging products. The prepared material systems were exposed to controlled climatic ageing simulating long-term solar radiation and cyclic outdoor conditions. The degradation of the biocomposite systems was evaluated via thermal (differential scanning calorimetry) and mechanical properties (tensile and flexural tests, Charpy impact toughness). In addition to evaluating the degradation of the material structures using standardized tests, the influence and effect of controlled climatic ageing was visually assessed using SEM images (electron microscopy) of the surfaces and fracture surfaces of the test specimens.

Sustainable Valorization of Bioplastic Waste: A Review on Effective Recycling Routes for the Most Widely Used Biopolymers

Plastics-based materials have a high carbon footprint, and their disposal is a considerable problem for the environment. Biodegradable bioplastics represent an alternative on which most countries have focused their attention to replace of conventional plastics in various sectors, among which food packaging is the most significant one. The evaluation of the optimal end-of-life process for bioplastic waste is of great importance for their sustainable use. In this review, the advantages and limits of different waste management routes-biodegradation, mechanical recycling and thermal degradation processes-are presented for the most common categories of biopolymers on the market, including starch-based bioplastics, PLA and PBAT. The analysis outlines that starch-based bioplastics, unless blended with other biopolymers, exhibit good biodegradation rates and are suitable for disposal by composting, while PLA and PBAT are incompatible with this process and require alternative strategies. The thermal degradation process is very promising for chemical recycling, enabling building blocks and the recovery of valuable chemicals from bioplastic waste, according to the principles of a sustainable and circular economy. Nevertheless, only a few articles have focused on this recycling process, highlighting the need for research to fully exploit the potentiality of this waste management route.

Bioaugmentation with a defined bacterial consortium: A key to degrade high molecular weight polylactic acid during traditional composting

Polylactic acid (PLA) is commercialized as a compostable bio-thermoplastic. PLA degrades under industrial composting conditions where elevated temperatures are maintained for a long timeframe. However, these conditions cannot be achieved in a non-industrial compost pile. Therefore, this study aims to degrade high molecular weight PLA films by adding a PLA-degrading bacterial consortium (EAc) comprised of Nocardioides zeae EA12, Stenotrophomonas pavanii EA33, Gordonia desulfuricans EA63, and Chitinophaga jiangningensis EA02 during traditional composting. With EAc-bioaugmentation, PLA films (5-30% w/w) had complete disintegration (35 d), 77-82% molecular weight reduction (16 d), and higher CO₂ liberation and mineralization than non-bioaugmented composting. Bacterial community analyses showed that EAc-bioaugmentation increased the relative abundance of Schlegelella, a known polymer degrader, and interacted positively with beneficial indigenous microbes like Bacillus, Schlegelella and Thermopolyspora. The bioaugmentation also decreased compost phytotoxicity. Hence, consortium EAc shows potential in PLA-waste treatment applications, such as backyard and small-scale composting.

The Influence of Plasticizers and Accelerated Ageing on Biodegradation of PLA under Controlled Composting Conditions

The overall performance of plasticizers on common mechanical and physical properties, as well as on the processability of polylactic acid (PLA) films, is well-explored. However, the influence of plasticizers on biodegradation is still in its infancy. In this study, the influence of natural-based dicarboxylic acid-based ester plasticizers (MC2178 and MC2192), acetyl tributyl citrate (ATBC Citroflex A4), and polyethylene glycol (PEG 400) on the biodegradation of extruded PLA films was evaluated. Furthermore, the influence of accelerated ageing on the performance properties and biodegradation of films was further investigated. The biodegradation of films was determined under controlled thermophilic composting conditions (ISO 14855-1). Apart from respirometry, an evaluation of the degree of disintegration, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM) of film surfaces was conducted. The influence of melt-processing with plasticizers has a significant effect on structural changes. Especially, the degree of crystallinity has been found to be a major factor which affects the biodegradation rate. The lowest biodegradation rates have been evaluated for films plasticized with PEG 400. These lower molecular weight plasticizers enhanced the crystallinity degrees of the PLA phase due to an increase in chain mobility. On the contrary, the highest biodegradation rate was found for films plasticized with MC2192, which has a higher molecular weight and evoked minimal structural changes of the PLA. From the evaluated results, it could also be stated that migration of plasticizers, physical ageing, and chain scission of films prompted by ageing significantly influenced both the mechanical and thermal properties, as well as the biodegradation rate. Therefore, the ageing of parts has to be taken into consideration for the proper evolution of the biodegradation of plasticized PLA and their applications.

The Physical Properties and Crystallization Kinetics of Biocomposite Films Based on PLLA and Spent Coffee Grounds

In the context of today's needs for environmental sustainability, it is important to develop new materials that are based on renewable resources and biodegrade at the end of their life. Bioplastics reinforced by agricultural waste have the potential to cause a revolution in many industrial applications. This paper reports the physical properties and crystallization kinetics of biocomposite films based on poly(L-lactic acid) (PLLA) and 10 wt.% of spent coffee grounds (SCG). To enhance adhesion between the PLLA matrix and SCG particles, a compatibilizing agent based on itaconic anhydride (IA)-grafted PLLA (PLLA-g-IA) was prepared by reactive extrusion using dicumyl peroxide (DCP). Furthermore, due to the intended application of the film in the packaging industry, the organic plasticizer acetyl tributyl citrate (ATBC) is used to improve processing and increase ductility. The crystallization behavior and thermal properties were observed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Crystallinity degree increased from 3,5 (neat PLLA) up to 48% (PLLA/PLLA-g-IA/ATBC/SCG) at the highest cooling rate. The physical properties were evaluated by tensile testing and dynamic mechanical analysis (DMA). The combination of the compatibilizer, SCG, and ATBC led to a synergistic effect that positively influenced the supramolecular structure, internal damping, and overall ductility of the composite films.

Additive Manufacturing of Anatomical Poly(d,l-lactide) Scaffolds

Poly(lactide) (PLA) is one of the most investigated semicrystalline polymers for material extrusion (MEX) additive manufacturing (AM) techniques based on polymer melt processing. Research on its application for the development of customized devices tailored to specific anatomical parts of the human body can provide new personalized medicine strategies. This research activity was aimed at testing a new multifunctional AM system for the design and fabrication by MEX of anatomical and dog-bone-shaped PLA samples with different infill densities and deposition angles. In particular, a commercial PLA filament was employed to validate the computer-aided design (CAD) and manufacturing (CAM) process for the development of scaffold prototypes modeled on a human bone defect. Physical-chemical characterization of the obtained samples by 1H-NMR spectroscopy, size exclusion chromatography (SEC), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) demonstrated a small reduction of polymer molecular weight (~5%) due to thermal processing, as well as that the commercial polymer employed was a semicrystalline poly(d,l-lactide). Mechanical characterization highlighted the possibility of tuning elastic modulus and strength, as well as the elongation at break up to a 60% value by varying infill parameters.

The Influence of Additives and Environment on Biodegradation of PHBV Biocomposites

The biodegradation of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) ternary biocomposites containing nature-based plasticizer acetyl tributyl citrate (ATBC), heterogeneous nucleation agents-calcium carbonate (CaCO₃) and spray-dried lignin-coated cellulose nanocrystals (L-CNC)-in vermicomposting, freshwater biotope, and thermophilic composting have been studied. The degree of disintegration, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and the evaluation of surface images taken by scanning electron microscopy (SEM) were conducted for the determination influence of different environments and additives on the biodegradation of PHBV. Furthermore, the method adapted from ISO 14855-1 standard was used for thermophilic composting. It is a method based on the measurement of the amount of carbon dioxide evolved during microbial degradation. The highest biodegradation rate was observed in the thermophilic condition of composting. The biodegradation level of all PHBV-based samples was, after 90 days, higher than 90%. Different mechanisms of degradation and consequently different degradation rate were evaluated in vermicomposting and freshwater biotope. The surface enzymatic degradation, observed during the vermicomposting process, showed slightly higher biodegradation potential than the hydrolytic attack of freshwater biotope. The application of ATBC plasticizers in the PHBV matrix caused an increase in biodegradation rate in all environments. However, the highest biodegradation rate was achieved for ternary PHBV biocomposites containing 10 wt. % of ATBC and 10 wt. % of CaCO₃. A considerable increase in the degree of disintegration was evaluated, even in freshwater biotope. Furthermore, the slight inhibition effect of L-CNC on the biodegradation process of ternary PHBV/ATBC/L-CNC could be stated.

Water-soluble polyvinyl alcohol composite films with nanodiamond particles modified with polyethyleneimine

Nanodiamond particles modified with polyethyleneimine were added to polyvinyl alcohol matrices to obtain composites with good thermal and mechanical properties.

Recent progress of preparation of branched poly(lactic acid) and its application in the modification of polylactic acid materials

Poly (lactic acid) (PLA) with branched structure has abundant terminal groups, high melt strength, good rheological properties, and excellent processability; it is a new research and application direction of PLA materials. This study mainly summarizes the molecular structure design, preparation methods, basic properties of branched PLA, and its application in modified PLA materials. The structure and properties of branched PLA prepared by ring-opening polymerization of monomer, functional group polycondensation, and chain extender in the processing process were introduced. The research progress of in situ formation of branched PLA by initiators, multifunctional monomers/additives through dynamic vulcanization, and irradiation induction was described. The effect of branched PLA on the structure and properties of linear PLA materials was analyzed. The role of branched PLA in improving the crystallization behavior, phase morphology, foaming properties, and mechanical properties of linear PLA materials was discussed. At the same time, its research progress in biomedicine and tissue engineering was analyzed. Branched PLA has excellent compatibility with PLA, which has important research value in regulating the structure and properties of PLA materials.

End of Life of Biodegradable Plastics: Composting versus Re/Upcycling

Nowadays the issues related to the end of life of traditional plastics are very urgent due to the important pollution problems that plastics have caused. Biodegradable plastics can help to try to mitigate these problems, but even bioplastics need much attention to carefully evaluate the different options for plastic waste disposal. In this Minireview, three different end-of-life scenarios (composting, recycling, and upcycling) were evaluated in terms of literature review. As a result, the ability of bioplastics to be biodegraded by composting has been related to physical variables and materials characteristics. Hence, it is possible to deduce that the process is mature enough to be a good way to minimize bioplastic waste and valorize it for the production of a fertilizer. Recycling and upcycling options, which could open up many interesting new scenarios for the production of high-value materials, are less studied. Research in this area can be strongly encouraged.

Polylactic acid production from biotechnological routes: A review

Polylactic acid (PLA) has been highlighted as an important polymer due to its high potential for applicability in various areas, such as in the chemical, medical, pharmaceutical or biotechnology field. Very recently, studies have reported its use as a basic component for the production of personal protective equipment (PPE) required for the prevention of Sars-Cov-2 contamination, responsible for the cause of coronavirus disease, which is currently a major worldwide sanitary and social problem. PLA is considered a non-toxic, biodegradable and compostable plastic with interesting characteristics from the industrial point of view, and it emerges as a promising product under the concept of "green plastic", since most of the polymers produced currently are petroleum-based, a non-renewable raw material. Biotechnology routes have been mentioned as potential methodologies for the production of this polymer, especially by enzymatic routes, in particular by use of lipases enzymes. The availability of pure lactic acid isomers is a fundamental aspect of the manufacture of PLA with more interesting mechanical and thermal properties. Due to the technological importance that PLA-based polymers are acquiring, as well as their characteristics and applicability in several fields, especially medical, pharmaceutical and biotechnology, this review article sought to gather very recent information regarding the development of research in this area. The main highlight of this study is that it was carried out from a biotechnological point of view, aiming at a totally green bioplastic production, since the obtaining of lactic acid, which will be used as raw material for the PLA synthesis, until the degradation of the polymer obtained by biological routes.