The Demulsification Properties of Cationic Hyperbranched Polyamidoamines for Polymer Flooding Emulsions and Microemulsions

Demulsification of Crude Oil Emulsions Using Versatile and Eco-Friendly Demulsifiers Based on Cellulose Decorated with Imidazolium-Bearing Triazole Moiety

Water in the crude oil forms emulsions that must be broken before refining processes. Here, the novel and versatile derivatives of imidazolium ionic liquids (ILs) containing triazole moiety [SIm-TazCn][Br] were synthesized via click chemistry and then grafted onto the cellulose (CEL) to prepare eco-friendly demulsifiers for breaking water-in-oil (W/O) emulsions. The prepared compounds with two kinds of alkyl chains named CEL[SIm-TazC6][Br] and CEL[SIm-TazC10][Br] were characterized and employed for demulsifying W/O (30:70 and 50:50 vol %) emulsions. Also, the effect of the type and concentration of each demulsifier on the phase separation and dehydration efficiency (DE) were investigated through the bottle test. According to the bottle test results, the CEL[SIm-TazC6][Br] derivative at 4000 ppm showed a good DE of 79% after 5 min, which increased to 82% after 24 h. The interfacial tension (IFT) of derivatives at different concentrations was measured. The minimum IFT value of 16.3 mN/m was obtained for CEL[SIm-TazC6][Br] with a shorter alkyl chain at 4000 ppm after 24 h. The green and efficient CEL-based surfactants significantly demulsified the W/O emulsions because of the collaboration between imidazolium and triazole moieties.

Investigation of Dioctyl Sodium Sulfosuccinate in Demulsifying Crude Oil-in-Water Emulsions

This research investigated the performance of dioctyl sodium sulfosuccinate (DSS), a double-chain anionic surfactant, in breaking crude oil-in-water emulsions. The response surface methodology was used to consider the effect of the DSS concentration, oil concentration, and shaking time on demulsification efficiency and obtain optimum demulsification conditions. Further single-factor experiments were conducted to investigate the effects of salinity, crude oil conditions (fresh and weathered), and gravity separation settling time. The results showed that DSS efficiently demulsified stable emulsions under different oil concentrations (500-3000 mg/L) within 15 min shaking time. Increasing DSS concentration to 900 mg/L (critical micelle concentration) increased the demulsification efficiency to 99%. DSS not only improved the demulsification efficiency but also did not impede the demulsifier interfacial adsorption at the oil-water interface due to the presence of the double-chain structure. The low molecular weight enables the homogeneous distribution of DSS molecules in the emulsion, leading to a high demulsification efficiency within 15 min. Analysis of variance results indicated the importance of considering the interaction of oil concentration and shaking time in demulsification. DSS could reduce the total extractable petroleum hydrocarbons in the separated water to <10 mg/L without gravity separation and could achieve promising demulsification performance at high salinity (36 g/L) and various concentrations of fresh and weathered oil. The demulsification mechanism was explained by analyzing the microscopic images and the transmittance of the emulsion. DSS could be an efficient double-chain anionic surfactant in demulsifying stable oil-in-water emulsions.

Demulsification Treatment of Spent Metalworking Fluids by Metal Cations: The Synergistic Effect and Efficiency Evaluation

In this paper, various metal ions were utilized for the demulsification of spent metalworking fluids discharged from an automobile parts workshop. Five types of metal ions, i.e., Fe3+, Al3+, Fe2+, Ca2+ and Mg2+, combined with coagulant were systematically evaluated, and the synergistic effect as well as the optimum operating conditions were studied. The results indicated that the Ca2+ as well Mg2+ possessed hardly efficiency for the demulsification, on the contrary, Fe2+ reduced the yield of the by-product sludge and lowered the SV30 ratio, and Al3+ boosted the CODCr removal. Furthermore, Fe3+ and Al3+ had a significant synergistic effect to achieve a better transmittance and a higher CODCr/SV30 ratio which revealed that more CODCr was removed, as well as less by-product sludge was generated. For a better demulsification of spent metalworking fluids, the optimum operating conditions were gathered as follows: the dosage of metal ions was 0.08 mol/L with Al3+:Fe3+ ratio was 1.5:1, the reaction pH was 6.00, the reaction time was 18.00 min and the temperature was 323.00 K. Based on this, the CODCr removal, the SV30 ratio and the transmittance and CODCr/SV30 ratio of the spent metalworking fluids were 80.21%, 40.00%, 95.20% and 128.33 mg/mL, respectively. This combined metal ion demulsification method possessed an advantageous minimization of spent metalworking fluids, which greatly benefited the automobile parts workshops in cutting down the operating cost in environmental protection.

Progressive Applications of Hyperbranched Polymer Based on Diarylamine: Antimicrobial, Anti-Biofilm and Anti-Aerobic Corrosion

New generations of hyperbranched aramids were synthesized from diarylamine and methyl acrylate using an AB₂ monomer approach in a straightforward one-pot preparation. The chemical structure of hyperbranched Phenylenediamine/Methyl Acrylate HB(PDMA was confirmed by Fourier Transform Infrared (FTIR) and Nuclear Magnetic Resonance (¹HNMR) spectroscopy. In addition, the particle’s size and distribution were recorded using Dynamic Light Scattering (DLS). Moreover, the synthesized HB(PDMA)s displayed broad-spectrum antimicrobial activities against Gram-positive and Gram-negative bacteria as well as yeast strains and anti-biofilm activity where the highest activity was attributed to HB(PDMA)G₄ at the lowest Minimum Inhibitory, Minimum Bactericidal, and Fungicidal Concentrations (MIC, MBC, and MFC, respectively). Furthermore, the HB(PDMA)s expressed anti-bacterial activity against isolated Pseudomonas sp. (R301) at a salinity of 35,000 ppm (NaCl). In addition, they revealed different corrosion inhibition efficiencies at the cultivated medium salinity at the estimated minimum bactericidal concentrations. The highest metal corrosion inhibition efficiencies were 59.5 and 94.3% for HB(PDMA)G₄ at the Minimum Bactericidal Concentrations (MBCs) and two times Minimum Bactericidal Concentrations (2XMBCs), respectively, in comparison to both negative and positive controls.