Particle Fabrication Using Inkjet Printing onto Hydrophobic Surfaces for Optimization and Calibration of Trace Contraband Detection Sensors

pH effects on capture efficiency and deposition patterns in sessile droplet immunoassays: An XDLVO analysis

Immunosensors are crucial for various applications, with capture efficiency and detection time as key performance parameters. Sessile droplets on functionalized substrates have demonstrated potential as micro-reactors for antibody-antigen binding, reducing detection time and analyte volume due to the presence of convective currents. Tuning the surface charges by adjusting buffer pH can modulate antigen capture efficiency. While the impact of pH has been studied on antibody-antigen binding in flow and non-flow systems, the use of sessile droplets and the specific impact of buffer pH on the capture efficiency of surface-functionalized antibodies remains understudied. Understanding how pH affects capture and deposition patterns is vital for optimizing immunosensor design. Additionally, the mechanisms governing internal flow within the droplet and dominant driving forces require further investigation. We investigated the effect of varying buffer pH on prostate-specific antigen (PSA) capture by anti-PSA functionalized polydimethylsiloxane substrates. Capture efficiency was measured using the Brown-Anson model applied to cyclic voltammetry, validated with electrochemical impedance spectroscopy. pH significantly influenced PSA capture by surface-immobilized anti-PSA IgG. The extended Derjaguin-Landau-Verwey-Overbeek theory explained the interplay between pH and internal flow. Micro-particle image velocimetry (PIV) confirmed internal flow, primarily driven by Marangoni flow from solute concentration gradients. Controlling buffer pH in biosensors offers higher capture efficiency and desired deposition patterns. These insights advance immunosensor design and hold potential for biomedical and diagnostic applications.

Raman Spectroscopy of Disperse Systems with Varying Particle Sizes and Correction of Signal Losses

In this paper, a dispersion of glass beads of different sizes in an ammonium nitrate solution is investigated with the aid of Raman spectroscopy. The signal losses caused by the dispersion are quantified by an additional scattered light measurement and used to correct the measured ammonium nitrate concentration. Each individual glass bead represents an interface at which the excitation laser is deflected from its direction causing distortion in the received Raman signal. It is shown that the scattering losses measured with the scattered light probe correlate with the loss of the Raman signal, which means that the data obtained can be used to correct the measured values. The resulting correction function considers different particle sizes in the range of 2-99 µm as well as ammonium nitrate concentrations of 0-20 wt% and delivers an RMSEP of 1.952 wt%. This correction provides easier process access to dispersions that were previously difficult or impossible to measure.

Raman Spectroscopy of Glass Beads in Ammonium Nitrate Solution and Compensation of Signal Losses

In the present study, the influence of disperse systems on Raman scattering was investigated. How an increasing particle concentration weakens the quantitative signal of the Raman spectrum is shown. Furthermore, the change in the position of the optimal measurement point in the fluid was considered in detail. Additional transmission measurements can be used to derive a simple and robust correction method that allows the actual concentration of the continuous phase to be determined with a standard deviation of 2.6%.

New Conceptional Study of a Portable Highly Sensitive Photometric Raman Sensor

Quality control and reaction monitoring are necessary to ensure the consistency of any kind of mixing or reaction process. In this context, a novel portable high-sensitivity sensor prototype based on the Raman effect is presented in this study. The elongated probe head is designed for (but not limited to) monitoring high temperature batch processes for quality assurance. Thanks to the highly sensitive special detectors, concentration differences of up to 50 mmol/L can currently be detected, which facilitates compliance with high product quality standards. In addition, seamless reaction tracking is possible. Small individual adjustments through simple, intuitive mechanical components provide a high degree of flexibility in reaction selection by the end user. Specially developed software automates the evaluation process and gives the user visual signals about the current status and progress of the batch as well as an emergency stop if temperature limits could damage individual components. By using all the individual components developed, the problem of the limited integration times of previous spectrometric measuring instruments could be reduced. The prototype was validated using concentration measurements of various substances that occur as standard in batch processes. In addition, this article provides an outlook on the fact that Raman measurements can also be carried out successfully and reliably in explosive environments in the future with the prototype presented.

DART-MS Spectral Similarity of Infrared Thermally Desorbed Solid Particulate and Solution Cast Propellant Samples

Security and forensic applications employ test and reference materials to develop, calibrate, and validate analytical instrumentation such as mass spectrometry for the trace detection and chemical analysis of target analytes. An emerging class of target analytes includes homemade fuel oxidizer explosives based on pyrotechnics, propellants, and powder mixtures. Test materials for these compounds must appropriately and accurately embody the physical and chemical nature of the threat. Precision liquid deposition methods have long been employed for creation of trace level test materials. Mass spectral similarity and chemical signature differences between solid particulate and solution cast (i.e., liquid deposited) propellant samples were investigated by infrared thermal desorption direct analysis in real time mass spectrometry (IRTD-DART-MS). Differences in the mass spectra and ion distributions of solid and liquid deposited black powders and black powder substitutes were observed. These differences were attributed to chemical processes (e.g., degradation) and physical differences in the crystal formation, spatial distribution, morphology, and size. The production and deposition of test and reference materials remain critical to developing new technologies and detecting evolving threats.

Drying of Ethanol/Water Droplets Containing Silica Nanoparticles

The evaporation of colloidal drop on a substrate with a pinned contact line usually results in a ring stain (the so-called coffee-ring effect). In this paper, we present an investigation of the evaporation of sessile picoliter droplets of binary solvent mixtures containing fumed silica nanoparticles (NPs). The internal flows in ethanol/water droplets are suppressed, and a uniform deposit morphology is achieved with a low loading (0.2-0.5 vol %) of hydrophobic fumed silica NPs. The effective control of the particle deposit morphology is based on a rapid sol-gel transition assisted by preferential evaporation of ethanol. For droplets of dilute suspensions, the fumed silica NPs tend to agglomerate and form an elastic network quickly, starting from the region close to the three-phase contact line and below the gas-liquid interface and growing toward the interior of the droplet as the solvents evaporate and the surface descends. Higher silica particle concentrations, lower ethanol concentrations, and weaker Marangoni flows all contribute to the sol-gel transition and hence to the suppression of the coffee-ring effect.

Combining Inkjet Printing with Emulsion Solvent Evaporation to Pattern Polymeric Particles

We demonstrate a concept to produce deposits of polymer in the form of particles by inkjet printing an emulsion in which the discrete phase evaporates preferentially. An oil/water emulsion with polymer contained inside the oil phase is used as ink for printing. Circular deposits of spherical polymer particles with uniform thickness are obtained. The effects of the hydrophobicity of substrates and the physical properties of the oil on the morphology of the deposits are explored. The deposit of aggregated polymeric particles can be transformed into a uniform film by annealing if required. This strategy for the patterning of polymer materials in the form of either particles or a film works for mixtures of polymers and functional cargoes.