Smart Bioimpedance Spectroscopy Device for Body Composition Estimation

Improving Precision of Bioimpedance Spectroscopic Analysis for Lymphedema and Lipedema Assessment

Background: Bioimpedance spectroscopy (BIS) is commonly used for the detection and monitoring of lymphedema and potentially lipedema. BIS measures limb electrical resistance, which decreases with fluid accumulation in these conditions. R0, the index of extracellular fluid and lymph accumulation, is typically estimated using Cole modeling, but technical and biological factors can affect accuracy. Methods: Participants with clinically affirmed bilateral leg lymphedema, lipedema, self-ascribed swelling, and healthy controls were included in this study. Impedance measurements were taken using a stand-on BIS device, and R0 was estimated using both the Cole modeling method and a regression approach. Quality of data fitting was assessed visually and statistically. Results: Control participants were younger and lighter compared with the clinical groups. The regression method was able to analyze 100% of participant data, whereas the Cole method was successful in only 80%-88% of cases in the lymphedema and lipedema groups. Additionally, the regression approach provided better curve fitting accuracy for all participants. Conclusion: The regression method offers a robust alternative for estimating R0 values in BIS data, especially in lower limb assessments where data analysis is challenging. The small difference between methods in absolute R0 values (2.5%) has minimal practical implications, suggesting interchangeability in data analysis. The Cole method showed poorer performance, particularly in participants with lymphedema, possibly due to differences in water proportions and limb size. Overall, the regression method can be effectively used in clinical practice for estimating R0 values in BIS data, offering a more accurate and reliable approach than traditional Cole plotting methods.

Smart Bioimpedance Device for the Assessment of Peripheral Muscles in Patients with COPD

Muscle dysfunction and muscle atrophy are common complications resulting from Chronic Obstructive Pulmonary Disease (COPD). The evaluation of the peripheral muscles can be carried out through the assessment of their structural components from ultrasound images or their functional components through isometric and isotonic strength tests. This evaluation, performed mainly on the quadriceps muscle, is not only of great interest for diagnosis, prognosis and monitoring of COPD, but also for the evaluation of the benefits of therapeutic interventions. In this work, bioimpedance spectroscopy technology is proposed as a low-cost and easy-to-use alternative for the evaluation of peripheral muscles, becoming a feasible alternative to ultrasound images and strength tests for their application in routine clinical practice. For this purpose, a laboratory prototype of a bioimpedance device has been adapted to perform segmental measurements in the quadriceps region. The validation results obtained in a pseudo-randomized study in patients with COPD in a controlled clinical environment which involved 33 volunteers confirm the correlation and correspondence of the bioimpedance parameters with respect to the structural and functional parameters of the quadriceps muscle, making it possible to propose a set of prediction equations. The main contribution of this manuscript is the discovery of a linear relationship between quadriceps muscle properties and the bioimpedance Cole model parameters, reaching a correlation of 0.69 and an average error of less than 0.2 cm regarding the thickness of the quadriceps estimations from ultrasound images, and a correlation of 0.77 and an average error of 3.9 kg regarding the isometric strength of the quadriceps muscle.

A Taxonomy for Health Information Systems

The health sector is highly digitized, which is enabling the collection of vast quantities of electronic data about health and well-being. These data are collected by a diverse array of information and communication technologies, including systems used by health care organizations, consumer and community sources such as information collected on the web, and passively collected data from technologies such as wearables and devices. Understanding the breadth of IT that collect these data and how it can be actioned is a challenge for the significant portion of the digital health workforce that interact with health data as part of their duties but are not for informatics experts. This viewpoint aims to present a taxonomy categorizing common information and communication technologies that collect electronic data. An initial classification of key information systems collecting electronic health data was undertaken via a rapid review of the literature. Subsequently, a purposeful search of the scholarly and gray literature was undertaken to extract key information about the systems within each category to generate definitions of the systems and describe the strengths and limitations of these systems.

Assessment of bioimpedance spectroscopy devices: a comparative study and error analysis of gold-plated copper electrodes

Objective. Bioimpedance spectroscopy (BIS) is a non-invasive diagnostic tool to derive fluid volume compartments from frequency dependent voltage drops in alternating currents by extrapolating to the extracellular resistance (R0) and intracellular resistance (Ri). Here we tested whether a novel BIS device with reusable and adhesive single-use electrodes produces results which are (in various body positions) equivalent to an established system employing only single-use adhesive electrodes.Approach. Two BIS devices ('Cella' and the 'Body Composition Monitor' [BCM]) were compared using four dedicated resistance testboxes and by measuring 40 healthy volunteers.Invivocomparisons included supine wrist-to-ankle (WA) reference measurements and wrist-to-wrist (WW) measurements with pre-gelled silver/silver-chloride (Ag/AgCl) electrodes and WW measurements with reusable gold-plated copper electrodes.Main results. Coefficient of variation were <1% for all testbox measurements with both BIS devices. Accuracy was within ±1% of true resistance variability, a threshold which was only exceeded by the Cella device for all resistances in a testbox designed with a lowR0/Riratio.Invivo, WA-BIS differed significantly between BIS devices (p< 0.001). Reusable WW electrodes exhibited larger resistances than WW-BIS with Ag/AgCl electrodes (R0: 738.36 and 628.69 Ω;Ri: 1508.18 and 1390 Ω) and the relative error varied from 7.6% to 31.1% (R0) and -15.6% to 37.3% (Ri).Significance. Both BIS devices produced equivalent resistances measurements but different estimates of body composition bothinsilicoand in WA setupsinvivo, suggesting that the devices should not be used interchangeably. Employing WW reusable electrodes as opposed to WA and WW measurement setups with pre-gelled Ag/AgCl electrodes seems to be associated with measurement variations that are too large for safe clinical use. We recommend further investigations of measurement errors originating from electrode material and current path.

Design and Manufacturing of Equipment for Investigation of Low Frequency Bioimpedance

The purpose of this study was to highlight a method of making equipment for the investigation of low frequency bioimpedance. A constant current with an average value of I = 100 µA is injected into the human body via means of current injection electrodes, and the biological signal is taken from the electrodes of electric potential charged with the biopotentials generated by the human body. The resulting voltage, ΔU is processed by the electronic conditioning system. The mathematical model of the four-electrode system in contact with the skin, and considering a target organ, was simplified to a single equivalent impedance. The capacitive filter low passes down from the differential input of the first instrumentation amplifier together with the isolated capacitive barrier integrated in the precision isolated secondary amplifier and maintains the biological signal taken from the electrodes charged with the undistorted biopotentials generated by the human body. Mass loops are avoided, and any electric shocks or electrostatic discharges are prevented. In addition, for small amplitudes of the biological signal, electromagnetic interferences of below 100 Hz of the power supply network were eliminated by using an active fourth-order Bessel filtering module. The measurements performed for the low frequency of f = 100 Hz on the volunteers showed for the investigated organs that the bioelectrical resistivities vary from 90 Ωcm up to 450 Ωcm, and that these are in agreement with other published and disseminated results for each body zone.

Comparative Study of Measurement Methods for Embedded Bioimpedance Spectroscopy Systems

Bioimpedance spectroscopy (BIS) is an advanced measurement method for providing information on impedance changes at several frequencies by injecting a low current into a device under test and analyzing the response voltage. Several methods have been elaborated for BIS measurement, calculating impedance with a gain phase detector (GPD), IQ demodulation, and fast Fourier transform (FFT). Although the measurement method has a big influence on the measurement system performance, a systematical comparative study has not been performed yet. In this paper, we compare them based on simulations and experimental studies. To maintain similar conditions in the implementation of all methods, we use the same signal generator followed by a voltage-controlled current source (VCCS) as a signal generator. For performance analysis, three DUTs have been designed to imitate the typical behavior of biological tissues. A laboratory impedance analyzer is used as a reference. The comparison addresses magnitude measurement accuracy, phase measurement accuracy, signal processing, hardware complexity, and power consumption. The result shows that the FFT-based system excels with high accuracy for amplitude and phase measurement while providing the lowest hardware complexity, and power consumption, but it needs a much higher software complexity.

Preliminary study on parameterization of raw electrical bioimpedance data with 3 frequencies

This study tests the geometrical parameterization method for Electrical Bio-Impedance Spectroscopy (EBIS) readings previously proposed by one of the authors. This method uses the data of just three frequencies (therefore called 3P method). The test was carried out by the analysis of parameterization from 26 spectra (selected from 13 data sets) by the non-linear square (NLS) method, the 3P method and a combination of the two (3P-NLS). Additionally, the behaviour of the 3P method for 4 levels of noise and 3 different ways of segmenting the spectra were also explored with a MATLAB simulation of 400 spectra. Finally, a system for the classification of EBIS readings is presented, based on deviations of the raw data from the semi-circle obtained by the parameterization methods. Overall, the results suggest a very good performance of the 3P method when compared with the other two. The 3P method performs very well with levels of noise of 1 and 2%, but performs poorly with levels of noise of 5% and 10%. The results support the idea that the 3P method could be used with confidence for the parameterization of EBIS spectra, after the selection of three adequate frequencies according to specific applications.

Scientific Developments and New Technological Trajectories in Sensor Research

Scientific developments and new technological trajectories in sensors play an important role in understanding technological and social change. The goal of this study is to develop a scientometric analysis (using scientific documents and patents) to explain the evolution of sensor research and new sensor technologies that are critical to science and society. Results suggest that new directions in sensor research are driving technological trajectories of wireless sensor networks, biosensors and wearable sensors. These findings can help scholars to clarify new paths of technological change in sensors and policymakers to allocate research funds towards research fields and sensor technologies that have a high potential of growth for generating a positive societal impact.

Current Status and Progress in the Treatment of Lower Limb Lymphedema After Treatment of Gynecological Oncology

Purpose: To discuss the status and progress of treatment of lower limb lymphedema (LLL) after gynecological cancer treatment. Common gynecological malignancies include endometrial cancer, cervical cancer, ovarian cancer, and vulvar cancer. LLL is one of the common complications after gynecological cancer treatment. LLL is one of the common complications after gynecological cancer treatment, which seriously affects patients' quality of life. Methods: We searched the Medline database for literature on LLL after gynecological oncology treatment, reviewed the incidence and risk factors for LLL in different gynecological malignancies, and summarized advances in the prevention and treatment of LLL after gynecological malignancy treatment. Finally, we review data-based approaches for the treatment of LLL and discuss experimental therapies currently in development. Results: Treatment of LLL is usually combined, conservative, and surgical. Complete decongestive therapy is the gold standard for the treatment of LLL. Prevention and treatment of lymphedema of the lower extremities are important for patients with gynecological cancers. Conclusion: Clinicians should be aware of the prevention and treatment of LLL, with a precise diagnosis and effective intervention at an early stage to delay its progression and improve patients' quality of life.

Electrical Tomography Reconstruction Using Reconfigurable Waveforms in a FPGA

The principal objective of this research is to conceive a mobile system based on electrical tomography for subsurface imaging and monitoring in order to enable simultaneous recording of electrical potentials of cardiac and pulmonary activity. For an exploration of excitation waveforms in electrical tomography, specialized hardware is required. As the main principle of tomography is the measurement of electrical perturbations on an unknown object, it is crucial to synchronize excitation and sensing processes in a very precise way for the purpose of acquiring meaningful data. To cope with this problem, an FPGA device is used, with an architecture that allows us to trigger excitation signals and to read sensed data simultaneously via independent processes that share the same clock. In this way, waveform reconfiguration on frequency and shape can be provided and studied. The system is connected to a standard microcontroller SoC with a simple API that allows for IoT capabilities for on-line operation and tracking, given that the design is targeted for in vivo medical monitoring. As a result of the research work, a measuring device was developed, the surface data analyzed and the image was reconstructed using the selected configuration.

Cole-Impedance Model Representations of Right-Side Segmental Arm, Leg, and Full-Body Bioimpedances of Healthy Adults: Comparison of Fractional-Order

The passive electrical properties of a biological tissue, referred to as the tissue bioimpedance, are related to the underlying tissue physiology. These measurements are often well-represented by a fractional-order equivalent circuit model, referred to as the Cole-impedance model. Objective: Identify if there are differences in the fractional-order (α) of the Cole-impedance parameters that represent the segmental right-body, right-arm, and right-leg of adult participants. Hypothesis: Cole-impedance model parameters often associated with tissue geometry and fluid (R∞, R1, C) will be different between body segments, but parameters often associated with tissue type (α) will not show any statistical differences. Approach: A secondary analysis was applied to a dataset collected for an agreement study between bioimpedance spectroscopy devices and dual-energy X-ray absoptiometry, identifying the Cole-model parameters of the right-side body segments of N=174 participants using a particle swarm optimization approach. Statistical testing was applied to the different groups of Cole-model parameters to evaluate group differences and correlations of parameters with tissue features. Results: All Cole-impedance model parameters showed statistically significant differences between body segments. Significance: The physiological or geometric features of biological tissues that are linked with the fractional-order (α) of data represented by the Cole-impedance model requires further study to elucidate.

Bioimpedance Sensor and Methodology for Acute Pain Monitoring

The paper aims to revive the interest in bioimpedance analysis for pain studies in communicating and non-communicating (anesthetized) individuals for monitoring purpose. The plea for exploitation of full potential offered by the complex (bio)impedance measurement is emphasized through theoretical and experimental analysis. A non-invasive, low-cost reliable sensor to measure skin impedance is designed with off-the-shelf components. This is a second generation prototype for pain detection, quantification, and modeling, with the objective to be used in fully anesthetized patients undergoing surgery. The 2D and 3D time-frequency, multi-frequency evaluation of impedance data is based on broadly available signal processing tools. Furthermore, fractional-order impedance models are implied to provide an indication of change in tissue dynamics correlated with absence/presence of nociceptor stimulation. The unique features of the proposed sensor enhancements are described and illustrated here based on mechanical and thermal tests and further reinforced with previous studies from our first generation prototype.

Physical Validation of a Residual Impedance Rejection Method during Ultra-Low Frequency Bio-Impedance Spectral Measurements

Accurate and reliable measurement of the electrical impedance spectrum is an essential requirement in order to draw relevant conclusions in many fields and a variety of applications; in particular, for biological processes. Even in the state-of-the-art methods developed for this purpose, the accuracy and efficacy of impedance measurements are reduced in biological systems, due to the regular occurrence of parameters causing measurement errors such as residual impedance, parasitic capacitance, generator anomalies, and so on. Recent observations have reported the necessity of decreasing such inaccuracies whenever measurements are performed in the ultra-low frequency range, as the above-mentioned errors are almost entirely absent in such cases. The current research work proposes a method which can reject the anomalies listed above when measuring in the ultra-low frequency range, facilitating data collection at the same time. To demonstrate our hypothesis, originating from the consideration of the determinant role of the measuring frequency, a physical model is proposed to examine the effectiveness of our method by measuring across the commonly used vs. ultra-low frequency ranges. Validation measurements reflect that the range of frequencies and the accuracy is much greater than in state-of-the-art methods. Using the proposed new impedance examination technique, biological system characterization can be carried out more accurately.

Special Issue "Body Sensors Networks for E-Health Applications"

Body Sensor Networks (BSN) have emerged as a particularization of Wireless Sensor Networks (WSN) in the context of body monitoring environments, closely linked to healthcare applications. These networks are made up of smart biomedical sensors that allow the monitoring of physiological parameters and serve as the basis for e-Health applications. This Special Issue collects some of the latest developments in the field of BSN related to new developments in biomedical sensor technologies, the design and experimental characterization of on-body/in-body antennas and new communication protocols for BSN, including some review studies.