Highly Stretchable and Transparent Ionic Conductor with Novel Hydrophobicity and Extreme-Temperature Tolerance

Superstrong Ionogel Enabled by Coacervation-Induced Nanofibril Assembly for Sustainable Moisture Energy Harvesting

Ionogels have grabbed significant interest in various applications, from sensors and actuators to wearable electronics and energy storage devices. However, current ionogels suffer from low strength and poor ionic conductivity, limiting their performance in practical applications. Here, inspired by the mechanical reinforcement of natural biomacromolecules through noncovalent aggregates, a strategy is proposed to construct nanofibril-based ionogels through complex coacervation-induced assembly. Cellulose nanofibrils (CNFs) can bundle together with poly(ionic liquid) (PIL) to form a superstrong nanofibrous network, in which the ionic liquid (IL) can be retained to form ionogels with high liquid inclusion and ionic conductivity. The strength of the CNF-PIL-IL ionogels can be tuned by the IL content over a wide range of up to 78 MPa. The optical transparency, high strength, and hygroscopicity enabled them to be promising candidates in moist-electricity generation and applications such as energy harvesting windows and wearable power generators. In addition, the ionogels are degradable and the ionogel-based generators can be recycled through dehydration. Our strategy suggests perspectives for the fabrication of high-strength and multifunctional ionogels for sustainable applications.

Transparent, super stretchable, freezing-tolerant, self-healing ionic conductive cellulose based eutectogel for multi-functional sensors

In this study, we propose a non - toxic and low-cost fabrication of cellulose-based eutectogel through the ZnCl2/H2O/H3PO4 deep eutectic solvent (DES) to dissolve cellulose followed by free-radical polymerization of acrylamide. Particularly, the introduction of cellulose enhances the mechanical properties of eutectogels while eliminating the environmental concerns of the traditional nanocellulose fabrication process. Owing to the dynamic transfer of ions in the eutectogel network, the prepared eutectogels exhibit adjustable conductivity (0.9- 1.37 Sm-1, 15 °C) and stretching sensitivity (Gauge factor = 5.4). The resulting DES - cellulose-based eutectogels (DCEs) exhibited ultra stretchability (4086 %), high toughness (261.3 MJ/m3), excellent ionic conductivity (1.64 Sm-1, 20 °C), high transparency (>85 %), outstanding antifreezing performance (<-80 °C), and other comprehensive characteristics. The DCEs had been proven to have multiple sensitivities to external stimuli, like temperature, strain, and pressure. As a result, the DCEs can be assembled into multifunctional sensors. Moreover, this work also demonstrated the satisfactory performance of DCEs in flexible electroluminescent devices. The low cost and high efficiency made the preparation method of this experiment an efficient strategy for developing high-performance cellulose-based eutectogels, which would greatly promote the application of such materials in areas such as artificial skin for soft robots and other wearable devices.

Fluorine-Containing Ionogels with Stretchable, Solvent-Resistant, Wide Temperature Tolerance, and Transparent Properties for Ionic Conductors

Stretchable ionogels, as soft ion-conducting materials, have generated significant interest. However, the integration of multiple functions into a single ionogel, including temperature tolerance, self-adhesiveness, and stability in diverse environments, remains a challenge. In this study, a new class of fluorine-containing ionogels was synthesized through photo-initiated copolymerization of fluorinated hexafluorobutyl methacrylate and butyl acrylate in a fluorinated ionic liquid 1-butyl-3-methyl imidazolium bis (trifluoromethylsulfonyl) imide. The resulting ionogels demonstrate good stretchability with a fracture strain of ~1300%. Owing to the advantages of the fluorinated network and the ionic liquid, the ionogels show excellent stability in air and vacuum, as well as in various solvent media such as water, sodium chloride solution, and hexane. Additionally, the ionogels display impressive wide temperature tolerance, functioning effectively within a wide temperature range from -60 to 350 °C. Moreover, due to their adhesive properties, the ionogels can be easily attached to various substrates, including plastic, rubber, steel, and glass. Sensors made of these ionogels reliably respond to repetitive tensile-release motion and finger bending in both air and underwater. These findings suggest that the developed ionogels hold great promise for application in wearable devices.

Digital Light Processing 4D Printing of Poloxamer Micelles for Facile Fabrication of Multifunctional Biocompatible Hydrogels as Tailored Wearable Sensors

The lack of both digital light processing (DLP) compatible and biocompatible photopolymers, along with inappropriate material properties required for wearable sensor applications, substantially hinders the employment of DLP 3D printing in the fabrication of multifunctional hydrogels. Herein, we discovered and implemented a photoreactive poloxamer derivative, Pluronic F-127 diacrylate, which overcomes these limitations and is optimized to achieve DLP 3D printed micelle-based hydrogels with high structural complexity, resolution, and precision. In addition, the dehydrated hydrogels exhibit a shape-memory effect and are conformally attached to the geometry of the detection point after rehydration, which implies the 4D printing characteristic of the fabrication process and is beneficial for the storage and application of the device. The excellent cytocompatibility and in vivo biocompatibility further strengthen the potential application of the poloxamer micelle-based hydrogels as a platform for multifunctional wearable systems. After processing them with a lithium chloride (LiCl) solution, multifunctional conductive ionic hydrogels with antifreezing and antiswelling properties along with good transparency and water retention are easily prepared. As capacitive flexible sensors, the DLP 3D printed micelle-based hydrogel devices exhibit excellent sensitivity, cycling stability, and durability in detecting multimodal deformations. Moreover, the DLP 3D printed conductive hydrogels are successfully applied as real-time human motion and tactile sensors with satisfactory sensing performances even in a -20 °C low-temperature environment.

Stable Flexible Electronic Devices under Harsh Conditions Enabled by Double-Network Hydrogels Containing Binary Cations

Hydrogels are increasingly used in flexible electronic devices, but the mechanical and electrochemical stabilities of hydrogel devices are often limited under specific harsh conditions. Herein, chemically/physically cross-linked double-network (DN) hydrogels containing binary cations Zn2+ and Li+ are constructed in order to address the above challenges. Double networks of chemically cross-linked polyacrylamide (PAM) and physically cross-linked κ-Carrageenan (κ-CG) are designed to account for the mechanical robustness while binary cations endow the hydrogels with excellent ionic conductivity and outstanding environmental adaptability. Excellent mechanical robustness and ionic conductivity (25 °C, 2.26 S·m-1; -25 °C, 1.54 S·m-1) have been achieved. Utilizing the DN hydrogels containing binary cations as signal-converting materials, we fabricated flexible mechanosensors. High gauge factors (resistive strain sensors, 2.4; capacitive pressure sensors, 0.82 kPa-1) and highly stable sensing ability have been achieved. Interestingly, zinc-ion hybrid supercapacitors containing the DN hydrogels containing binary cations as electrolytes have achieved an initial capacity of 52.5 mAh·g-1 at a current density of 3 A·g-1 and a capacity retention rate of 82.9% after 19,000 cycles. Proper working of the zinc-ion hybrid supercapacitors at subzero conditions and stable charge-discharge for more than 19,000 cycles at -25 °C have been demonstrated. Overall, DN hydrogels containing binary cations have provided promising materials for high-performance flexible electronic devices under harsh conditions.

Ionic Liquid/Water Binary Solvent Anti-Freezing Hydrogel for Strain and Temperature Sensors

Hydrogels are widely applied in the flexible wearable electronic devices field owing to their skin-like stretchability, superb biocompatibility, and high conductivity retention under mechanical deformations. Nevertheless, hydrogels are prone to freezing at low temperatures and losing water at high temperatures, which seriously limits their practical applications. Herein, a binary solvent system of ionic liquid (1-ethyl-3-methylimidazolium chloride) and water was prepared to endow the ionic hydrogel high ionic conductivity (0.28 S m-1 at 25 °C), high transparency (94.26%), and superior freezing tolerance (-50 °C). The multiple hydrogen bonds formed among polymer chains, water, and ionic liquids significantly improved the mechanical properties of the ionic hydrogel, enabling excellent tensile properties (strain >1800%) and durability (1000 times at 100% strain). Moreover, the ionic hydrogel was further assembled into a dual-response sensor, which exhibited satisfactory sensitivity to both tension (gauge factor = 2.15 at 200% strain) and temperature (temperature coefficient of resistance = -1.845%/°C) and can be applied for human motion and body temperature monitoring. This study provides a versatile method for preparing multifunctional hydrogels with a wide range of applications and lays the groundwork for human movement detection and smart health care.

Hydrogen Bonds Reinforced Ionogels with High Sensitivity and Stable Autonomous Adhesion as Versatile Ionic Skins

Flexible wearable sensors have demonstrated enormous potential in various fields such as human health monitoring, soft robotics, and motion detection. Among them, sensors based on ionogels have garnered significant attention due to their wide range of applications. However, the fabrication of ionogels with high sensitivity and stable autonomous adhesion remains a challenge, thereby limiting their potential applications. Herein, we present an advanced ionogel (PACG-MBAA) with exceptional performances based on multiple hydrogen bonds, which is fabricated through one-step radical polymerization of N-acryloylglycine (ACG) in 1-ethyl-3-methylimidazolium ethyl sulfate (EMIES) in the presence of N,N'-methylenebis(acrylamide) (MBAA). Compared with the ionogel (PAA-MBAA) formed by polymerization of acrylic acid (AA) in EMIES, the resulting ionogel exhibits tunable mechanical strength (35-130 kPa) and Young's modulus comparable to human skin (60-70 kPa) owing to the multiple hydrogen bonds formation. Importantly, they demonstrate stable autonomous adhesion to various substrates and good self-healing capabilities. Furthermore, the ionogel-based sensor shows high sensitivity (with a gauge factor up to 6.16 in the tensile range of 300-700%), enabling the detection of both gross and subtle movements in daily human activities. By integration of the International Morse code, the ionogel-based sensor enables the encryption, decryption, and transmission of information, thus expanding its application prospects.

Hydrophobic deep eutectic solvent-based eutectogels for underwater sensing

Eutectogels derived from deep eutectic solvents (DESs) exhibit great potential for the fabrication of flexible sensors. However, the hygroscopicity of eutectogels hinders their applications in underwater sensing. In this work, a hydrophobic eutectogel with exceptional long-term underwater stability is produced through one-step polymerization of lauryl methacrylate and glycidyl methacrylate in a hydrophobic DES. The hydrophobic gel network and hydrophobic DES fulfill the eutectogel with outstanding water resistance (water contact angle > 110°) and excellent mechanical properties in an aqueous environment, thus leading to extraordinary durability (over 1000 testing cycles). Additionally, based on this eutectogel, underwater strain and pressure sensors with high sensitivity, rapid responsiveness, and superior durability were fabricated for accurate real-time monitoring of human activity. Furthermore, it has been demonstrated that the eutectogel sensor can transmit information through Morse code, performing as a wearable underwater communicator. This research provides an exemplary way for a demonstration method of hydrophobic eutectogel for durable underwater applications.

Recent Progress in Self-Healable Hydrogel-Based Electroluminescent Devices: A Comprehensive Review

Flexible electronics have gained significant research attention in recent years due to their potential applications as smart and functional materials. Typically, electroluminescence devices produced by hydrogel-based materials are among the most notable flexible electronics. With their excellent flexibility and their remarkable electrical, adaptable mechanical and self-healing properties, functional hydrogels offer a wealth of insights and opportunities for the fabrication of electroluminescent devices that can be easily integrated into wearable electronics for various applications. Various strategies have been developed and adapted to obtain functional hydrogels, and at the same time, high-performance electroluminescent devices have been fabricated based on these functional hydrogels. This review provides a comprehensive overview of various functional hydrogels that have been used for the development of electroluminescent devices. It also highlights some challenges and future research prospects for hydrogel-based electroluminescent devices.

Multimaterial Three-Dimensional Printing of Ultraviolet-Curable Ionic Conductive Elastomers with Diverse Polymers for Multifunctional Flexible Electronics

Ionic conductive elastomers (ICEs) are emerging stretchable and ionic conductive materials that are solvent-free and thus demonstrate excellent thermal stability. Three-dimensional (3D) printing that creates complex 3D structures in free forms is considered as an ideal approach to manufacture sophisticated ICE-based devices. However, the current technologies constrain 3D printed ICE structures in a single material, which greatly limits functionality and performance of ICE-based devices and machines. Here, we report a digital light processing (DLP)-based multimaterial 3D printing capability to seemly integrate ultraviolet-curable ICE (UV-ICE) with nonconductive materials to create ionic flexible electronic devices in 3D forms with enhanced performance. This unique capability allows us to readily manufacture various 3D flexible electronic devices. To demonstrate this, we printed UV-ICE circuits into polymer substrates with different mechanical properties to create resistive strain and force sensors; we printed flexible capacitive sensors with high sensitivity (2 kPa^-1) and a wide range of measured pressures (from 5 Pa to 550 kPa) by creating a complex microstructure in the dielectric layer; we even realized ionic conductor-activated four-dimensional (4D) printing by printing a UV-ICE circuit into a shape memory polymer substrate. The proposed approach paves a new efficient way to realize multifunctional flexible devices and machines by bonding ICEs with other polymers in 3D forms.

Tough Ionogels: Synthesis, Toughening Mechanisms, and Mechanical Properties-A Perspective

Polymeric ionogels are polymer networks swollen with ionic liquids (i.e., salts with low melting points). Ionogels are interesting due to their unique features such as nonvolatility, high thermal and electrochemical stability, excellent ionic conductivity, and nonflammability. These properties enable applications such as unconventional electronics, energy storage devices (i.e., batteries and supercapacitors), sensors and actuators. However, the poor mechanical performance of ionogels (e.g., fracture strength < 1 MPa, modulus < 0.1 MPa, and toughness < 1000 J m^-2) have limited their use, thus motivating the need for tough ionogels. This Perspective summarizes recent advances toward tough ionogels by highlighting synthetic methods and toughening mechanisms. Opportunities and promising applications of tough ionogels are also discussed.

Mechanically Strong, Wet Adhesive, and Self-Healing Polyurethane Ionogel Enhanced with a Semi-interpenetrating Network for Underwater Motion Detection

The gel-based sensors have developed rapidly in recent years toward multifunctionality. However, there are still some challenges that need to be solved, such as poor mechanical properties and inaccessibility to wet or water environments. To address these issues, we have developed an ionogel with a semi-interpenetrating network structure by adopting poly(vinylidene fluoride-co-hexafluoropropylene) as the linear non-cross-linked network, a double-bonded ionic liquid and double-bonded capped polyurethane as the cross-linked network, and an ionic liquid as the conductive media. The obtained ionogel exhibits tunable mechanical properties (3.67-8.76 MPa) and excellent sensing properties (IG-20, GF = 8.2). The superb environmental stability and self-healing properties of the ionogel were also demonstrated. Meanwhile, adhesion, self-healing, and sensing performance were guaranteed for underwater due to the presence of a large number of C-F bonds. We strongly believe that this ionogel with excellent mechanical properties and underwater communication is expected for monitoring the health of the human body and information transmission in the future.

Patterned Magnetofluids via Magnetic Printing and Photopolymerization for Multifunctional Flexible Electronic Sensors

Liquid conductor-based flexible sensors with high mechanical deformability and reliable electrical reversibility have aroused great interest in electronic skin, soft robotics, environmental monitoring, and other fields. Herein, we develop a novel strategy to fabricate liquid conductor-based flexible sensors by combining ionic liquid-based magnetofluids (IL-MFs), magnetic printing, and photopolymerization techniques. The as-prepared sensors exhibit excellent electromechanical properties, such as a wide detection range, low hysteresis, fast response time, good durability, etc. Moreover, the gauge factors (GFs) of the sensor could be easily adjusted by changing the modulators with different line widths or patterns, and the strain sensors can also be designed for anisotropic monitoring. Apart from serving as strain sensors, the magnetofluid-based flexible sensors can be used to detect external pressure, human activities, and changes in temperature, illumination, and magnetic field as well. This work provides a facile strategy to fabricate liquid conductor-based multifunctional sensors. Such a magnetofluid-based sensor has a great promising future.

Wearable Sensors Adapted to Extreme Environments Based on the Robust Ionogel Electrolytes with Dual Hydrogen Networks

Nonvolatile ionogels are promising soft electrolyte materials for flexible electronics, but it is challenging to fabricate stable electrolytes with mechanical robustness. Here, through rationally optimizing the chemical structure of polymer matrix and ionic liquids, the high-performance ionogel electrolytes with mechanical robustness and stability were fabricated. There are double hydrogen bonding networks in the as-prepared ionogel electrolytes, one of which exists between the polymer chains while the other one existing between the polymer chains and ionic liquid molecules. By adjusting the content of the ionic liquid and the ratio of the two hydrogen bonding networks, the prepared ionogel electrolytes exhibit tunable properties with an elasticity of 1.3-30 kPa, a stretchability of more than 1800%, a fracture energy of 125.8-548.3 KJ m^-3, and a coordinated self-healing efficiency of 6.2-37.9% to satisfy the needs of different application scenarios. The assembled wearable sensors based on the high-performance ionogel electrolytes can be attached to a part of the human body, detecting various motions and body temperature. Benefiting from the nonvolatile and hydrophobic properties of the ionogel electrolytes, the wearable sensors can be operated under extreme environments including high/low temperature (-15^-100 °C) and high humidity (100% relative humidity). It is believed that this work provides prospects for the application of wearable electronic devices.

Tough and stretchable ionogels by in situ phase separation

Ionogels are compelling materials for technological devices due to their excellent ionic conductivity, thermal and electrochemical stability, and non-volatility. However, most existing ionogels suffer from low strength and toughness. Here, we report a simple one-step method to achieve ultra-tough and stretchable ionogels by randomly copolymerizing two common monomers with distinct solubility of the corresponding polymers in an ionic liquid. Copolymerization of acrylamide and acrylic acid in 1-ethyl-3-methylimidazolium ethyl sulfate results in a macroscopically homogeneous covalent network with in situ phase separation: a polymer-rich phase with hydrogen bonds that dissipate energy and toughen the ionogel; and an elastic solvent-rich phase that enables for large strain. These ionogels have high fracture strength (12.6 MPa), fracture energy (~24 kJ m^-2) and Young's modulus (46.5 MPa), while being highly stretchable (~600% strain) and having self-healing and shape-memory properties. This concept can be applied to other monomers and ionic liquids, offering a promising way to tune ionogel microstructure and properties in situ during one-step polymerization.

Hierarchical Response Network Boosts Solvent-Free Ionic Conductive Elastomers with Extreme Stretchability, Healability, and Recyclability for Ionic Sensors

The construction of solvent-free ionic conductive elastomers with high mechanical stretchability and large dynamic reversibility of chain segments is highly desired yet challenging. Here, a hierarchical response network strategy is presented for preparing highly stretchable yet mechanical robust ionic conductive elastomer composites (ICECs), among which poly(ethylene oxide) (PEO) microcrystalline serves as a physical cross-linking site providing high mechanical strength and elasticity, while dense hydrogen bonds endow superior mechanical toughness and dynamic reversibility. Due to the formation of the hierarchical response network, the resultant ICECs exhibit intrinsically high stretchability (>1500%), large tensile strength (∼2.1 MPa), and high fracture toughness (∼28 MJ m^-3). Intriguingly, due to the high reversibility of hydrogen-bonded networks, the ICECs after being crushed are capable of healing and recycling by simple hot-pressing for multiple cycles. Moreover, the ICECs are dissolvable under an alkaline condition and easily regenerated in an acid solution for manifold cycles. Importantly, the healed, recycled, and regenerated ICECs are capable of maintaining their initial mechanical elasticity and ionic conducting performance. Due to the integration of high stretchability, fatigue resistance, and ionic conductivity, the ICECs can readily work as a stretchable ionic conductor for skin-inspired ionic sensors for real-time and accurately sensing complex human motions. This study thus provides a promising strategy for the development of healable and renewable ionic sensing materials with high stretchability and mechanical robustness, demonstrating great potential in soft ionotronics.

Highly Stretchable, Fast Self-Healing, and Waterproof Fluorinated Copolymer Ionogels with Selectively Enriched Ionic Liquids for Human-Motion Detection

The development of waterproof ionogels with high stretchability and fast self-healing performance is essential for stretchable ionic conductors in sophisticated skin-inspired wearable sensors but can be rarely met in one material. Herein, a semicrystalline fluorinated copolymer ionogel (SFCI) with extremely high stretchability, underwater stability, and fast self-healability was fabricated, among which hydrophobic ionic liquids ([BMIM][TFSI]) were selectively enriched in fluoroacrylate segment domains of the fluorinated copolymer matrix through unique ion-dipole interactions. Benefiting from the reversible ion-dipole interactions between the [BMIM][TFSI] and fluoroacrylate segment domains as well as the physical cross-linking effects of semicrystalline oligoethylene glycol domains, the SFCI exhibited ultrastretchability (>6000%), fast room-temperature self-healability (>96% healing efficiency after cutting and self-healing for 30 min), and outstanding elasticity. In addition, the representative SFCI also exhibited high-temperature tolerance up to 300 °C, antifreezing performance as low as -35 °C, and high transparency (>93% visible-light transmittance). As a result, the as-obtained SFCI can readily be used as a highly stretchable ionic conductor in skin-inspired wearable sensors with waterproof performance for real-time detecting physiological human activities. These attractive features illustrate that the developed ultrastretchable and rapidly self-healable ionogels with unique waterproofness are promising candidates especially for sophisticated wearable strain sensing applications in complex and extreme environments.

Highly Transparent, Stretchable, and Conductive Supramolecular Ionogels Integrated with Three-Dimensional Printable, Adhesive, Healable, and Recyclable Character

In this work, we report the easy fabrication of highly transparent (optical transmittance above 93%), stretchable (1500-2500% elongation at break), and conductive (up to 2.25 S m^-1 at 25 °C) supramolecular ionogels that simultaneously integrate with three-dimensional (3D) printable, healable, adhesive, and recyclable character. The supramolecular ionogel is designed using a linear amphiphilic poly(urethane-urea) (PUU) copolymer and ionic liquid (IL) as the elastic scaffold and electrolyte, respectively, via a simple cosolvent method. Intriguingly, the 3D-printed highly conductive (2.25 S m^-1 at 25 °C) supramolecular ionogel structure shows record-high mechanical performance with a breaking tensile strain and stress of 945% and 1.51 MPa, respectively, and is able to lift 3400× or bear 10000× its weight without fracture. Furthermore, both the solution casting and 3D-printed ionogel films show high sensitivity and reliability for sensing a wide range of strains, including various human motions. The results present some new insights into the structural, mechanical, and functional design of novel multifunctional ionogels with distinguished mechanical performance and tractable processability, which will extend them to a wide range of flexible electronic applications, including artificial intelligence, wearable/conformable electronics, human/machine interactions, soft robotics, etc.

Dense Hydrogen-Bonding Network Boosts Ionic Conductive Hydrogels with Extremely High Toughness, Rapid Self-Recovery, and Autonomous Adhesion for Human-Motion Detection

The construction of ionic conductive hydrogels with high transparency, excellent mechanical robustness, high toughness, and rapid self-recovery is highly desired yet challenging. Herein, a hydrogen-bonding network densification strategy is presented for preparing a highly stretchable and transparent poly(ionic liquid) hydrogel (PAM-r-MVIC) from the perspective of random copolymerization of 1-methyl-3-(4-vinylbenzyl) imidazolium chloride and acrylamide in water. Ascribing to the formation of a dense hydrogen-bonding network, the resultant PAM-r-MVIC exhibited an intrinsically high stretchability (>1000%) and compressibility (90%), fast self-recovery with high toughness (2950 kJ m⁻³), and excellent fatigue resistance with no deviation for 100 cycles. Dissipative particle dynamics simulations revealed that the orientation of hydrogen bonds along the stretching direction boosted mechanical strength and toughness, which were further proved by the restriction of molecular chain movements ascribing to the formation of a dense hydrogen-bonding network from mean square displacement calculations. Combining with high ionic conductivity over a wide temperature range and autonomous adhesion on various surfaces with tailored adhesive strength, the PAM-r-MVIC can readily work as a highly stretchable and healable ionic conductor for a capacitive/resistive bimodal sensor with self-adhesion, high sensitivity, excellent linearity, and great durability. This study might provide a new path of designing and fabricating ionic conductive hydrogels with high mechanical elasticity, high toughness, and excellent fatigue resilience for skin-inspired ionic sensors in detecting complex human motions.

Hierarchical Network-Augmented Hydroglasses for Broadband Light Management

Light management is essential for military stealth, optical information communication, and energy-efficient buildings. However, current light management materials face challenges of limited optical modulation range and poor mechanical properties. Herein, we report a locally confined polymerization (LCP) approach to develop hierarchical network-augmented hydroglasses (HNAH) based on poly(methacrylic acid) for broadband light management as well as mechanical enhancement. The dynamic geometry of the networks ranging from nano- to micro-scale enables to manage the light wavelength over three orders of magnitude, from the ultraviolet (UV) to infrared (IR) band, and reversibly switches transmittance in the visible region. A smart hydroglass window is developed with elasticity, outstanding robustness, self-healing, notch resistance, biosafety by blocking UV radiation, and high solar energy shielding efficacy with a temperature drop of 13°C. Compared to current inorganic glasses and Plexiglas, the hydroglass not only is a promising and versatile candidate but also provides novel insights into the molecular and structural design of broadband light management and optimized mechanical properties.

Stretchable, Stable, and Room-Temperature Gas Sensors Based on Self-Healing and Transparent Organohydrogels

Conductive hydrogels have emerged as promising candidate materials for fabricating wearable electronics because of their fascinating stimuli-responsive and mechanical properties. However, the inherent instability of hydrogels seriously limits their application scope. Herein, the stable, ultrastretchable (upon to 1330% strain), self-healing, and transparent organohydrogel was exploited as a novel gas-responsive material to fabricate NH₃ and NO₂ gas sensors for the first time with extraordinary performance. A facile solvent substitution method was employed to convert the unstable hydrogel into the organohydrogel with a remarkable moisture retention (avoid drying within a year), frost resistance (freezing point below -130 °C), and unimpaired mechanical and gas sensing properties. First-principles simulations were performed to uncover the mechanisms of antidrying and antifreezing effects of organohydrogels and the interactions between NH₃/NO₂ and organohydrogels, revealing the vital role of hydrogen bonds in enhancing the stability and the adsorption of NH₃/NO₂ on the organohydrogel. The organohydrogel gas sensor displayed high sensitivity, ultralow theoretical limit of detection (91.6 and 3.5 ppb for NH₃ and NO₂, respectively), reversibility, and fast recovery at room temperature. It exhibited the capabilities to work at a highly deformed state with nondegraded sensing performance and restore all the electrical, mechanical, and sensing properties after mechanical damage. The gas sensing mechanism was understood by considering the gas adsorption on functional groups, dissolution in the solvent, and the hindering effect on the transport of ions.