Evaluating the efficacy of different techniques and irrigation solutions for removal of calcium hydroxide from the root canal system: A scanning electron microscope study

The Bond Strength of Root Canal Filling after Calcium Hydroxide Removal with a Simple Apical Negative Pressure Kit in Oval-Shaped Root Canal

Background

The aim of this study was to evaluate the effect of a simple irrigating device, which produced from the apical negative pressure concept, as a final irrigating method after calcium hydroxide (CH) medication on the bond strength of epoxy resin-based sealer in the oval-shaped root canal.

Methods

Forty-eight single-rooted premolars with oval-shaped canals were included in the study. The crown was decoronized and canal instrumented with Mtwo (VDW GmbH, Munich, Germany) up to size 40/04. The specimens were assigned to four groups according to the irrigation protocol after 1 week of CH medication: control group (no medication) and three experimental groups conventional needle irrigation (CNI), passive ultrasonic irrigation (PUI), and simple apical negative pressure kit (sANP). The teeth were obturated with a warm vertical technique using epoxy resin-based sealers. After 1 week, the roots were transversally sectioned at coronal, middle, and apical thirds. A push-out test was performed by a universal testing machine, and statistical analysis was performed using One-Way ANOVA with Duncan's post hoc test.

Results

The bond strength in the control group was significantly higher than the CNI group in all root canal thirds (P < 0.05). At coronal third, sANP showed lower bond strength than PUI group (P < 0.05). However, the bond strength of sANP group was comparable to the control group (P > 0.05) which was significantly higher than the PUI group at apical third (P < 0.05).

Conclusion

A sANP enhanced the bond strength of epoxy resin-based sealer in the apical third of CH-medicated root canal in the oval-shaped canal.

Endodontic cement penetration after removal of calcium hydroxide dressing using XP-endo finisher

We aimed to evaluate the penetration of endodontic cement following the removal of calcium hydroxide (Ca(OH)2) dressing using the XP-endo Finisher in association with different irrigating solutions. Sixty premolars were instrumented and applied with a Ca(OH)2 dressing. To remove Ca(OH)2, the teeth were divided into six groups, each with a different volume of sodium hypochlorite (NaOCl) and ethylenediaminetetraacetic acid (EDTA), as well as solution stirring time with XP-endo Finisher (0, 30, and 60 sec). Root canals were filled using the lateral condensation technique. Fluorescein dye was added to the cement for microscopic laser scanning analysis. In the generated images, linear measurements were taken in micrometers, and their averages were calculated. To analyze the perimeter penetration ratio of the cement, the total perimeter of the canal and the segment of the total perimeter of the canal where the endodontic cement penetrated into the dentinal tubules were measured in micrometers. We found that using an XP-endo Finisher in irrigation was more effective than using a needle and syringe during the extension and penetration of endodontic cement. Shaking with XP-endo Finisher with 17% EDTA increased the extent and perimeter of the penetration of the endodontic cement into the dentinal tubules. However, using the XP-endo Finisher with EDTA only was more efficient than using the instrument interchangeably in NaOCl and EDTA. Although XP-endo Finisher contributes to the removal of Ca(OH)2, none of the protocols or instruments used removed all Ca(OH)2 from the root system.

Effect of obturation technique with immediate and delayed post space preparation on apical voids and bond strength of apical gutta-percha

Objective

The purpose of this study was to evaluate the effect of immediate and delayed post space preparation on the sealing ability of two root canal obturation techniques by using micro-computed tomography imaging and a push-out test.

Methods

The root canals of 40 human maxillary premolar teeth were instrumented and divided into four groups: (A) single cone (SC) followed by immediate post space preparation, (B) continuous wave of condensation (CWC) followed by immediate post space preparation, (C) SC followed by delayed post space preparation, and (D) CWC followed by delayed post space preparation. Micro-CT scans were performed for volumetric analysis of voids and filling materials in the apical 4-mm portion. A push-out test was performed, and failure modes (adhesive, cohesive, or mixed) were assessed. Data were analyzed using the Kruskal-Wallis test and one-way analysis of variance.

Results

No significant differences were observed among the four groups in terms of the percentage volume of voids of the apical 4 mm or the bond strength of apical gutta-percha.

Conclusions

The percentage volume of voids and bond strength of apical gutta-percha were similar and were not significantly influenced by the timing of post space preparation or the obturation technique.