Temperature Assessment of a Novel Pulsed Thulium Solid-State Laser Compared with a Holmium:Yttrium-Aluminum-Garnet Laser

Purpose: To compare a novel Thulium laser device with the commonly used Holmium:Yttrium-Aluminum-Garnet (Ho:YAG) laser in terms of the in vitro temperatures generated. Methods: Our study investigated and compared an evaluation model of a solid-state Thulium laser with a Medilas H Solvo 35 Holmium laser device, both by Dornier (Dornier MedTech Laser GmbH, Wessling, Germany). Our in vitro model consisted of a 20 mL test tube placed in a 37°C water bath. Constant irrigation was set at 50 mL/minute with a Reglo Z Digital pump (Cole Parmer, Chicago, IL). Four hundred micrometers of Dornier laser fibers were used. The temperature was measured with a type K thermocouple and a real-time data logger from Pico (PICO Technology, Cambridgeshire, United Kingdom). Power settings between 2 and 30 W were investigated. Each measurement lasted 120 seconds and was repeated five times. The data were evaluated by MATLAB^® (The Mathworks, Inc., Natick, MA). Results: The resulting temperatures were directly proportional to the power supplied. When comparing Holmium with Thulium, we observed maximum deviations of ≤0.82 K in temperatures at 120 seconds. The highest investigated laser power of 30 W yielded maximum temperatures differing by 6.7 K from the initial value. Out of the five comparisons, Thulium showed marginally yet significantly lower end temperatures in four cases and slightly lower cumulative equivalent minutes at 43°C (CEM₄₃) values in three cases. Conclusion: The Thulium laser resembles the Holmium device in the temperatures generated during in vitro application. An increase in laser power, thus, leads to equivalent increases in temperature that are largely independent of frequency, pulse duration, and single pulse energy. Pulsed Thulium:Yttrium-Aluminum-Garnet (Tm:YAG), Ho:YAG, and Thulium fiber laser seem to share a similar risk profile for patients in terms of temperature development. Intrarenal power outputs exceeding 10 W during clinical application should be compensated by ensuring sufficient irrigation.

Thermal effects of Ho:YAG laser lithotripsy during retrograde intrarenal surgery and percutaneous nephrolithotomy in an ex vivo porcine kidney model

PURPOSE

To evaluate the thermal effect of high-power holmium:yttrium-aluminum-garnet (Ho:YAG) laser lithotripsy in flexible/semirigid ureteroscopy (fURS/sURS) and percutaneous nephrolithotomy (PNL) in a standardized ex vivo porcine kidney model with real-time temperature assessment.

METHODS

The experimental setup consisted of three models designed to evaluate the thermal effects of Ho:YAG laser lithotripsy in fURS, sURS and PNL, respectively. In all setups, a postmortem porcine kidney was placed in a 37 °C water bath. Three thermocouples were inserted into the renal parenchyma while a flexible thermocouple was placed 3-4 mm proximal to the laser fiber to measure temperature variations in the collecting system. The thermal impact was evaluated in relation to laser power between 5 and 100 W and various irrigation rates (37 °C, 0-100 ml/min).

RESULTS

In all three experimental setups, sufficient irrigation was required to prevent potentially damaging temperatures into the renal pelvis and parenchyma. Even 5 W in fURS can lead to a potentially harming temperature rise if insufficient irrigation is applied. Particularly, high-power settings ≥ 30 W carry an elevated risk for critical temperature rises. The results allow the definition of a specific irrigation threshold for any power setting to prevent critical temperatures in the present study design.

CONCLUSIONS

Ho:YAG laser lithotripsy bears the risk of thermal damages to the urinary tract even at low-power settings if inadequate irrigation is applied. Sufficient irrigation is mandatory to perform safe Ho:YAG laser lithotripsy. Based on the results, we developed a formula calculating the approximate ΔT for irrigation rates ≥ 30 ml/min: ΔT = 15 K × (power [W]/irrigation [ml/min]).

Thermal effects of Ho: YAG laser lithotripsy: real-time evaluation in an in vitro model

PURPOSE

To evaluate the thermal effect of Ho:YAG laser lithotripsy in a standardized in vitro model via real-time temperature measurement.

METHODS

Our model comprised a 20 ml test tube simulating the renal pelvis that was immersed in a 37 °C water bath. Two different laser fibers [FlexiFib (15-45 W), RigiFib 1000 (45-100 W), LISA laser products OHG, Katlenburg-Lindau, Germany] were placed in the test tube. An Ho:YAG 100 W laser was used in all experiments (LISA). Each experiment involved 120 s of continuous laser application, and was repeated five times. Different laser settings (high vs. low frequency, high vs. low energy, and long vs. short pulse duration), irrigation rates (0 up to 100 ml/min, realized by several pumps), and human calcium oxalate stone samples were analyzed. Temperature data were acquired by a real-time data logger with thermocouples (PICO Technology, Cambridgeshire, UK). Real-time measurements were assessed using MatLab^®.

RESULTS

Laser application with no irrigation results in a rapid increase in temperature up to ∆28 K, rising to 68 °C at 100 W. Low irrigation rates yield significantly higher temperature outcomes. Higher irrigation rates result immediately in a lower temperature rise. High irrigation rates of 100 ml/min result in a temperature rise of 5 K at the highest laser power setting (100 W).

CONCLUSIONS

Ho:YAG laser lithotripsy might be safe provided that there is sufficient irrigation. However, high power and low irrigation resulted in potentially tissue-damaging temperatures. Laser devices should, therefore, always be applied in conjunction with continuous, closely monitored irrigation whenever performing Ho:YAG laser lithotripsy.