Synergistic Effects of Co3O4-gC3N4-Coated ZnO Nanoparticles: A Novel Approach for Enhanced Photocatalytic Degradation of Ciprofloxacin and Hydrogen Evolution via Water Splitting

This research evaluates the efficacy of catalysts based on Co3O4-gC3N4@ZnONPs in the degradation of ciprofloxacin (CFX) and the photocatalytic production of H2 through water splitting. The results show that CFX experiences prompt photodegradation, with rates reaching up to 99% within 60 min. Notably, the 5% (Co3O4-gC3N4)@ZnONPs emerged as the most potent catalyst. The recyclability studies of the catalyst revealed a minimal activity loss, approximately 6%, after 15 usage cycles. Using gas chromatography-mass spectrometry (GC-MS) techniques, the by-products of CFX photodegradation were identified, which enabled the determination of the potential degradation pathway and its resultant products. Comprehensive assessments involving photoluminescence, bandgap evaluations, and the study of scavenger reactions revealed a degradation mechanism driven primarily by superoxide radicals. Moreover, the catalysts demonstrated robust performance in H2 photocatalytic production, with some achieving outputs as high as 1407 µmol/hg in the visible spectrum (around 500 nm). Such findings underline the potential of these materials in environmental endeavors, targeting both water purification from organic pollutants and energy applications.

Effect of synthesis methods on the activity of NiO/Co3O4 as an electrode material for supercapacitor: in the light of X-ray diffraction study

The formation of heterostructures by combining individual components (NiO and Co3O4) is a preferred approach to enhance electrochemical performance as it leads to improved charge transfer and surface reaction kinetics. In the present work, a NiO/Co3O4 composite was prepared by two methods. First, neat NiO and Co3O4 were prepared by adopting the hydrothermal method followed by the formation of the composite (i) by a hydrothermal route (NC-Hydro) and (ii) by a calcination route (NC-Cal). NC-Hydro composite shows a specific capacity of 176 C g-1 at 1 A g-1 of current density in the three-electrode system in a 2 M KOH solution as an electrolyte with 90% cyclic retention after 5000 cycles at 4 A g-1. NC-Cal shows a specific capacity of 111 C g-1 at 1 A g-1 with 75% cyclic retention. The coulombic efficiency of NC-Hydro was 86.3% while for NC-Cal it was 42.3%. The reason behind the superior electrochemical performance of NC-Hydro in comparison to NC-Cal may be the large interlayer spacing and lattice parameters of the former, which provide large space for redox reactions. The unit cell volume of the composites was more than that of the constituents. This study reveals that the composites prepared by the hydrothermal method have superior electrochemical properties in comparison to composites prepared by the calcination method.

Prussian blue analogue-derived hollow metal oxide heterostructure for high-performance supercapacitors

Supercapacitors (SCs) have been the subject of considerable interest because of their distinct advantages. The performance of SCs is directly affected by the electrode materials. Metal oxides derived from Prussian blue analogues (PBAs) are often used as electrode materials for SCs. Herein, we developed a multi-step strategy to fabricate ternary hollow metal oxide (CuO/NiO/Co3O4) heterostructures. The core-shell structured PBA (NiHCC@CuHCC) with Ni-based PBA (NiHCC) as the core and Cu-based PBA (CuHCC) as the shell was prepared by a crystal seed method. The ternary metal oxide (CuO/NiO/Co3O4) with a hollow structure was obtained by calcinating NiHCC@CuHCC. The prepared CuO/NiO/Co3O4 demonstrates an excellent specific capacitance of 262.5 F g-1 at 1 A g-1, which is 27.4% and 16.2% higher than those of CuO/Co3O4 and NiO/Co3O4, respectively. In addition, the material showed outstanding cycling stability with a capacitance retention of 107.9% after 3000 cycles. The two-electrode system constructed with CuO/NiO/Co3O4 and nitrogen-doped graphene hydrogel (NDGH) demonstrates a stable and high energy density of 27.1 W h kg-1 at a power density of 1037.5 W kg-1. The capacitance retention rate was 100.7% after 4000 cycles. The reason for the excellent electrochemical properties could be the synergistic effect of the introduced heterojunction of CuO/NiO, the hollow structure, and various metal oxides. This strategy can greatly inspire the construction of SC electrodes.

Photocatalytic and Electrocatalytic Properties of Cu-Loaded ZIF-67-Derivatized Bean Sprout-Like Co-TiO2/Ti Nanostructures

ZIF-derivatized catalysts have shown high potential in catalysis. Herein, bean sprout-like Co-TiO2/Ti nanostructures were first synthesized by thermal treatment at 800 °C under Ar-flow conditions using sacrificial ZIF-67 templated on Ti sheets. It was observed that ZIF-67 on Ti sheets started to thermally decompose at around 350 °C and was converted to the cubic phase Co3O4. The head of the bean sprout structure was observed to be Co3O4, while the stem showed a crystal structure of rutile TiO2 grown from the metallic Ti support. Cu sputter-deposited Co-TiO2/Ti nanostructures were also prepared for photocatalytic and electrocatalytic CO2 reduction performances, as well as electrochemical oxygen reaction (OER). Gas chromatography results after photocatalytic CO2 reduction showed that CH3OH, CO and CH4 were produced as major products with the highest MeOH selectivity of 64% and minor C2 compounds of C2H2, C2H4 and C2H6. For electrocatalytic CO2 reduction, CO, CH4 and C2H4 were meaningfully detected, but H2 was dominantly produced. The amounts were observed to be dependent on the Cu deposition amount. Electrochemical OER performances in 0.1 M KOH electrolyte exhibited onset overpotentials of 330-430 mV (vs. RHE) and Tafel slopes of 117-134 mV/dec that were dependent on Cu-loading thickness. The present unique results provide useful information for synthesis of bean sprout-like Co-TiO2/Ti hybrid nanostructures and their applications to CO2 reduction and electrochemical water splitting in energy and environmental fields.

Enhancement of propane combustion activity over CoOx catalysts by introducing C2–C5 diols

C₂–C₅ diols effectively promote the degradation of propane by weakening the Co–O bond strength of CoO_x.

Cobalt supported on carbon nanotubes for methane chemical vapor deposition for the production of new carbon nanotubes

Well-structured CNT were produced over Co/CNT catalysts. The final products do not require a purification procedure for support catalyst removal.

Energy Storage and CO2 Reduction Performances of Co/Co2C/C Prepared by an Anaerobic Ethanol Oxidation Reaction Using Sacrificial SnO2

Co/Co2C/C hybrids were prepared employing a new synthetic route and demonstrated as materials for energy storage and CO2 recycling application. Herein, an anaerobic ethanol oxidation reaction over Co3O4 nanoparticles (NPs) was first employed to fabricate Co/Co2C/C hybrids using sacrificial SnO2. In the absence of SnO2, Co3O4 NPs were converted to alpha and beta metallic Co. On the other hand, using sacrificial SnO2 resulted in the formation of Co2C and Co embedded in the carbon matrix at approximately 450 °C, as determined by temperature-programmed mass spectrometry analysis. The newly developed materials were fully examined by X-ray diffraction crystallography, scanning electron microscopy, energy-dispersive X-ray analysis, high-resolution transmission electron microscopy, and X-ray photoelectron spectroscopy. The Co/Co2C/C hybrids showed a specific capacitance of 153 F/g at a current density of 0.5 A/g. Photocatalytic CO2 reduction experiments were performed and generated CO, CH4, and CH3OH as reduction products with yields of 47.7, 11.0, and 23.4 μmol/g, respectively. The anaerobic ethanol oxidation reaction could be a very useful method for the development of carbon-supported metal carbides, which have not been achieved by other synthetic methods. Furthermore, the demonstration tests unveiled new application areas of Co carbide materials.

Contrasting Effects of Potassium Addition on M3O4 (M = Co, Fe, and Mn) Oxides during Direct NO Decomposition Catalysis

While the promotional effect of potassium on Co3O4 NO decomposition catalytic performance is established in the literature, it remains unknown if K is also a promoter of NO decomposition over similar simple first-row transition metal spinels like Mn3O4 and Fe3O4. Thus, potassium was impregnated (0.9–3.0 wt.%) on Co3O4, Mn3O4, and Fe3O4 and evaluated for NO decomposition reactivity from 400–650 °C. The activity of Co3O4 was strongly dependent on the amount of potassium present, with a maximum of ~0.18 [(µmol NO to N2) g−1 s−1] at 0.9 wt.% K. Without potassium, Fe3O4 exhibited deactivation with time-on-stream due to a non-catalytic chemical reaction with NO forming α-Fe2O3 (hematite), which is inactive for NO decomposition. Potassium addition led to some stabilization of Fe3O4, however, γ-Fe2O3 (maghemite) and a potassium–iron mixed oxide were also formed, and catalytic activity was only observed at 650 °C and was ~50× lower than 0.9 wt.% K on Co3O4. The addition of K to Mn3O4 led to formation of potassium–manganese mixed oxide phases, which became more prevalent after reaction and were nearly inactive for NO decomposition. Characterization of fresh and spent catalysts by scanning electron microscopy and energy dispersive X-ray analysis (SEM/EDX), in situ NO adsorption Fourier transform infrared spectroscopy, temperature programmed desorption techniques, X-ray powder diffraction (XRD), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS) revealed the unique potassium promotion of Co3O4 for NO decomposition arises not only from modification of the interaction of the catalyst surface with NOx (increased potassium-nitrite formation), but also from an improved ability to desorb oxygen as product O2 while maintaining the integrity and purity of the spinel phase.

Synthesis of 2D cobalt oxide nanosheets using a room temperature liquid metal

Room temperature liquid metals based on Ga can be used as a synthesis medium for the creation of metal oxide nanomaterials, however one thermodynamic limitation is that metals that are more easily oxidised than Ga are required to ensure their preferential formation. In this work we demonstrate a proof of principle approach whereby exposing the liquid metal alloyed with the required metal to acidic conditions circumvents preferential formation of Ga₂O₃ and allows for the formation of the required 2D transition metal oxide nanosheets. The synthesis procedure is straightforward in that it only requires bubbling oxygen gas through the liquid metal alloy into a solution of 10 mM HCl. We show that the formation of thin nanosheets of ca. 1 nm in thickness of CoO is possible. The material is characterised using transmission electron microscopy, atomic force microscopy, X-ray photoelectron and Raman spectroscopy. The electrocatalytic activity of the CoO nanosheets was investigated for the oxygen evolution reaction where the nanosheet thickness was found to be a factor influencing the activity. This proof of principle offers a route to the possible formation of many other 2D transition metal oxides from metals that are less readily oxidised than Ga by taking advantage of the interesting properties of room temperature liquid metals.

A RT liquid metal based on Ga can be used as a synthesis medium for creation of 2D nanosheets of cobalt oxide via expulsion of the sheets from the liquid metal surface into an acidic aqueous solution. The 2D nanosheets are shown to be active for OER.

Hierarchical Mesoporous/Macroporous Co-Doped NiO Nanosheet Arrays as Free-Standing Electrode Materials for Rechargeable Li-O2 Batteries

Lithium-oxygen (Li-O₂) batteries have been widely recognized as appealing power systems for their extremely high energy density versus common Li-ion batteries. However, there are still lots of issues that need to be addressed toward the practical application. Here, free-standing Co-doped NiO three-dimensional nanosheets were prepared by a hydrothermal synthesis method and directly employed as the air-breathing cathode of the Li-O₂ battery. The morphological phenomenon and electrochemical performance of the as-prepared cathode material were characterized by high-resolution scanning electron microscopy, X-ray diffraction, cyclic voltammetry, galvanostatic charge-discharge tests, and electrochemical impedance spectroscopy measurements. The Co-doped NiO electrode delivered a maximum discharge capacity of around 12 857 mA h g^-1 with a low overpotential (0.82 V) at 200 mA g^-1. Under upper-limit specific capacities of 500 mA h g^-1 at 400 mA g^-1, the Li-O₂ batteries exhibited a long cycle life of 165 cycles. Compared with the undoped NiO electrode, the Li-O₂ battery based on the Co-doped NiO cathode showed significantly higher oxygen reduction reaction and oxygen evolution reaction activities. This superior electrochemical performance is because of the partial substitution of Ni²⁺ in the NiO matrix by Co²⁺ to improve the p-type electronic conductivity of NiO. In addition, the morphology and specific surface area of NiO are affected by Co doping, which can expand the electrode-electrolyte contact area and lead to sufficient space for Li₂O₂ deposition. This approach harnesses the great potential of Co-doped NiO nanosheets for practical applications as advanced electrodes for rechargeable Li-O₂ batteries.

Co3O4-CuCoO2 Nanomesh: An Interface-Enhanced Substrate that Simultaneously Promotes CO Adsorption and O2 Activation in H2 Purification

Nanomaterials are widely used as redox-type reaction catalysts, while reactant adsorption and O₂ activation are hardly to be promoted simultaneously, restricting their applications in many important catalytic fields such as preferential CO oxidation (CO-PROX) in H₂-rich stream. In this work, an interface-enhanced Co₃O₄-CuCoO₂ nanomesh was initially synthesized by a hydrothermal process using aluminum powder as a sacrificial agent. This nanomesh is systematically characterized by powder X-ray diffraction, scanning electron microscopy, transmission electron microscopy, N₂ adsorption, X-ray photoelectron spectroscopy, UV-vis absorption spectroscopy, Raman spectroscopy, X-ray absorption near-edge spectroscopy, hydrogen temperature-programmed reduction, and oxygen temperature-programmed desorption. It is demonstrated that the nanomesh possesses high-density nanopores, enabling a large number of CO adsorption sites exposed to the surface. Meanwhile, electron transfer from O^2- to Co³⁺/Co²⁺ and the weakened bonding strength of Co-O bond at surfaces promoted the oxygen activation and redox ability of Co₃O₄. When tested as a catalyst for CO-PROX, this nanomesh with an optimized pore structure and a surface electronic structure, exhibits a strikingly high catalytic oxidation activity at low temperatures as well as a broader operation temperature window (i.e., CO conversion >99.0%, 100-200 °C) in the CO selective oxidation reaction. The present finding should be highly useful in promoting the quest for better CO-PROX catalysts, a hot topic for proton exchange membrane fuel cells and automotive vehicles.

Boosting photochemical activity by Ni doping of mesoporous CoO nanoparticle assemblies

Mesoporous Ni-implanted CoO nanoparticle assemblies possessing a suitable electronic structure and large mesoporosity deliver highly efficient photocatalytic Cr(vi) reduction and water oxidation activity.

Robust hierarchical 3D carbon foam electrode for efficient water electrolysis

Herein we report a 3D heterostructure comprising a hierarchical macroporous carbon foam that incorporates mesoporous carbon nanotubes decorated with cobalt oxide nanoparticles as an unique and highly efficient electrode material for the oxygen evolution reaction (OER) in electrocatalytic water splitting. The best performing electrode material showed high stability after 10 h, at constant potential of 1.7 V vs. RHE (reversible hydrogen electrode) in a 0.1 M KOH solution and high electrocatalytic activity in OER with low overpotential (0.38 V vs RHE at 10 mA cm⁻²). The excellent electrocatalytic performance of the electrode is rationalized by the overall 3D macroporous structure and with the firmly integrated CNTs directly grown on the foam, resulting in a large specific surface area, good electrical conductivity, as well as an efficient electrolyte transport into the whole electrode matrix concurrent with an ability to quickly dispose oxygen bubbles into the electrolyte. The eminent properties of the three-dimensional structured carbon matrix, which can be synthesized through a simple, scalable and cost effective pyrolysis process show that it has potential to be implemented in large-scale water electrolysis systems.

Role of Hydrogen and Oxygen Activation over Pt and Pd-Doped Composites for Catalytic Hydrogen Combustion

Removal of excess amount of hydrogen in a catalytic route is a safety measure to be implemented in fuel cell technologies and in nuclear power plants. Hydrogen and oxygen activation are crucial steps for hydrogen combustion that can be achieved by modifying supports with suitable noble metals. In the present study, Pt- and Pd-substituted Co₃O₄-ZrO₂ (CZ) were synthesized using PEG-assisted sonochemical synthesis. Ionic states of Pt and Pd in CZ supports were analyzed by X-ray photoelectron spectroscopy. Pd and Pt improved H₂ and O₂ activation extensively, which reduced the temperature of 50% conversion (T_50%) to 33 °C compared with the support (CZ). The activation energy of PdCZ catalyst was decreased by more than 2 folds (13.4 ± 1.2 kJ mol^-1) compared with CZ (34.3 ± 2.3 kJ mol^-1). The effect of oxygen vacancies in the reaction mechanism is found to be insignificant with Pt- and Pd-substituted CZ supports. However, oxygen vacancies play an important role when CZ alone was used as catalyst. The importance of hydrogen and oxygen activation as well as the oxygen vacancies in mechanism was studied by H₂-TPD, H₂-TPR, and in situ FTIR spectroscopy.

One for all: cobalt-containing polymethacrylates for magnetic ceramics, block copolymerization, unexpected electrochemistry, and stimuli-responsiveness

Functional cobalt-containing homo and block polymers are probed with respect to their redox-induced switchability and as preceramic materials.

A bubble-template approach for assembling Ni–Co oxide hollow microspheres with an enhanced electrochemical performance as an anode for lithium ion batteries

A bubble-template approach was developed to assemble Ni–Co oxide hollow microspheres with an enhanced electrochemical performance as an anode for lithium ion batteries.