[High accuracy measuring device for dental cast--using device with flat laser beam]

Reliability of linear and angular dental measurements with the OrthoMechanics Sequential Analyzer

INTRODUCTION

The aim of this study was to evaluate the reliability of newly developed software in the assessment of orthodontic tooth movement 3 dimensionally.

METHODS

The sample consisted of pretreatment and posttreatment computed tomography scans and plaster dental models of 20 orthodontic patients treated with a hyrax palatal expander as a part of their comprehensive orthodontic treatment. Dental-arch measurements, including arch widths, tooth inclinations, and angulation parameters, were measured on the scans using InvivoDental 3D imaging software (version 5.1; Motionview, Hixson, Tenn). The plaster dental models were laser scanned and superimposed, and measurements were obtained digitally using the new software. Agreement between the digital models and the computed tomography measurements was evaluated with intraclass correlation coefficients, paired t tests, and Bland-Altman plots. A P value of ≤0.05 was considered statistically significant.

RESULTS

High agreement, a nonsignificant paired t test, and no indication of agreement discrepancies were observed for most of the measured parameters.

CONCLUSIONS

The results confirmed that the new software program offers a reliable tool for dental-arch measurements obtained from 3-dimensional laser-scanned models.

Accuracy evaluation of a new three-dimensional reproduction method of edentulous dental casts, and wax occlusion rims with jaw relation

The article introduces a new method for three-dimensional reproduction of edentulous dental casts, and wax occlusion rims with jaw relation by using a commercial high-speed line laser scanner and reverse engineering software and evaluates the method's accuracy in vitro. The method comprises three main steps: (i) acquisition of the three-dimensional stereolithography data of maxillary and mandibular edentulous dental casts and wax occlusion rims; (ii) acquisition of the three-dimensional stereolithography data of jaw relations; and (iii) registration of these data with the reverse engineering software and completing reconstruction. To evaluate the accuracy of this method, dental casts and wax occlusion rims of 10 edentulous patients were used. The lengths of eight lines between common anatomic landmarks were measured directly on the casts and occlusion rims by using a vernier caliper and on the three-dimensional computerized images by using the software measurement tool. The direct data were considered as the true values. The paired-samples t-test was used for statistical analysis. The mean differences between the direct and the computerized measurements were mostly less than 0.04 mm and were not significant (P>0.05). Statistical significance among 10 patients was assessed using one-way analysis of variance (P<0.05). The result showed that the 10 patients were considered statistically no significant. Therefore, accurate three-dimensional reproduction of the edentulous dental casts, wax occlusion rims, and jaw relations was achieved. The proposed method enables the visualization of occlusion from different views and would help to meet the demand for the computer-aided design of removable complete dentures.

Measuring 3-dimensional tooth movement with a 3-dimensional surface laser scanner

INTRODUCTION

Our aims in this study were to (1) develop a method of measuring 3-dimensional (3D) tooth movement using a 3D surface laser scanner, (2) test the accuracy of this method, and (3) compare the measurements with those from cephalometric radiographs.

METHODS

A method of superimposing pretreatment and posttreatment models on the palatal rugae was developed, and an experimental model was prepared to evaluate the accuracy and reliability of the laser scanner. Records were obtained from a prospective longitudinal randomized clinical trial evaluating anchorage loss with headgears and midpalatal osseointegrated implants as a source of anchorage in Chesterfield, United Kingdom. The pretreatment and posttreatment study models were analyzed by using a 3D laser scanner to measure the 3D tooth movement.

RESULTS

The laser scanner was accurate to 0.0235 mm for anteroposterior measurements and 0.0071 mm for buccolingual movements for every 0.5 mm of movement. The study model analysis showed that mesial molar movements were 1.38 mm on the right side and 1.11 mm on the left side for the implant group, and 2.24 mm on right side and 1.63 mm on left side for the headgear group, with no statistically significant difference between the groups. The results for vertical movement of molars showed extrusion on both sides in both groups but no statistically significant difference between the groups. In the transverse plane, the results were not statistically significantly different between the groups. The results from superimposition of lateral cephalograms were similar to those obtained from the scanner.

CONCLUSIONS

The 3D laser scanner provides accurate and reliable measurements of tooth displacement and can be considered an alternative to cephalometric radiographs.

Maxillary Anterior Tooth Size and Arch Dimensions in Unilateral Cleft Lip and Palate

Objective:

To investigate differences in size of the maxillary permanent anterior teeth and arch dimensions between individuals with repaired unilateral cleft lip and palate (UCLP) and a matched control group representing the general population.

Design:

Retrospective study cast review.

Participants:

Study casts of 30 subjects due to commence orthodontic treatment following an alveolar bone graft (ABG) were collected from the Cleft Lip and Palate Units in South Yorkshire. Thirty control subjects were collected from a previously validated control group of white individuals in South Yorkshire.

Main Outcome Measures:

Casts were analyzed with an image analysis system to measure the dimensions of the maxillary permanent anterior teeth, incisor chord lengths, and the intercanine and intermolar widths. The results were analyzed statistically using paired t-tests and two-way univariate analysis of variance (ANOVA).

Results:

The mesiodistal widths of maxillary anterior teeth in the study group were smaller than the noncleft control group (p < .01). The dimensions of the cleft side maxillary incisors and incisor chord length were smaller (p < .05 and p < .01 respectively) compared with the noncleft side. The study group maxillary cleft side incisor chord length and maxillary intercanine width were narrower than the control group (p < .0001).

Conclusions:

(1) Anterior teeth are smaller mesiodistally in individuals with UCLP. (2) Maxillary incisors are smaller on the cleft side than the noncleft side. (3) UCLP subjects had smaller maxillary cleft side incisor chord lengths and intercanine widths than the control group despite pre-ABG expansion.

Use of an ultrahigh-speed laser scanner for constructing three-dimensional shapes of dentition and occlusion

STATEMENT OF PROBLEM

Acquisition of the 3-dimensional shape of dental casts is useful for quantitative evaluation of the diagnosis and treatment of occlusion.

PURPOSE

This study demonstrated the acquisition of data through the use of an ultrahigh-speed laser scanner and an originally developed goniometer, the use of these tools to measure the entire 3-dimensional shape of the dental cast from multiple directions, and the connection of the data measurements to reconstruct the cast's occlusion with the use of a computer.

MATERIAL AND METHODS

A commercially available apparatus that emits a line laser and completes 1 scan in only 0.6 seconds was used. To compensate for the unmeasured region, the cast was measured from 4 directions on the original goniometer, and the connection of data to obtain the entire image was carried out. Further, the reconstruction of the occlusion between the upper and lower casts was attempted by transferring the upper cast data to the lower cast.

RESULTS

By the data connection, the entire shape of the upper and lower casts was constructed, and the characteristic structure was reproduced. The data connections were satisfactory for the flat surfaces but less accurate for the inclined surfaces. Reconstruction of the occlusion between the upper and lower casts was accomplished. It was then possible to visualize the occlusion from arbitrary directions and sections with computer graphics.

CONCLUSION

The construction of the entire 3-dimensional shape of a dental cast and the reconstruction of the occlusion were accomplished using an ultrahigh-speed measurement system and original goniometer. These results will be useful for clinical applications such as computerized diagnoses and treatment of occlusion, and for the replacement of the stone casts in the dental office by computerized data.

Three-dimensional dental cast analyzing system using laser scanning

The purpose of this article is to introduce the outline of our newly developed three-dimensional dental cast analyzing system with laser scanning, and its preliminary clinical applications. The system is composed of a measuring device with a slit-ray laser projector and two sets of coupled charged devised video cameras, an image processing unit, a 16-bit personal computer as a controller, and an engineering workstation as a post processor. The dental cast is projected and scanned with a slit-ray laser beam. The raster coordinates of the target are determined with an image processor. Triangulation is applied to determine the location of each point. Generation of three-dimensional graphics of the dental cast takes approximately 40 minutes. About 90,000 sets of X, Y, Z coordinates are stored in the main memory of the microcomputer. The measurement error is less than 0.05 mm. Besides the conventional linear and angular measurements of the dental cast, we are also able to demonstrate the size of the palatal surface area and the volume of the oral cavity. The advantage of this system is that it facilitates the otherwise complicated and time-consuming mock surgery necessary for treatment planning in orthognathic surgery.